平面齿内齿轮一次包络鼓形蜗杆传动副性能测试

陈永洪; 陈燕; 王进戈; 张光辉

doi:10.3969/j.issn.0258-2724.2015.04.023

平面齿内齿轮一次包络鼓形蜗杆传动副性能测试

doi: 10.3969/j.issn.0258-2724.2015.04.023

基金项目:

国家自然科学青年基金资助项目(51405394)

四川省科技厅应用基础计划资助项目(2014JY0129)

详细信息

作者简介:
陈永洪(1984-),男,讲师,博士,研究方向为蜗杆传动,E-mail:chenyonghongjc@163.com

计量
- 文章访问数: 796
- HTML全文浏览量: 41
- PDF下载量: 559
- 被引次数: 0
出版历程
- 收稿日期: 2014-05-19
- 刊出日期: 2015-08-25

Performance Testing of Planar Internal Gear Primary-Enveloping Crown Worm Drive

摘要

摘要: 为了获取平面齿内齿轮一次包络鼓形蜗杆传动副(以下简称鼓形蜗杆传动副)的传动性能参数,以鼓形蜗杆传动副的啮合几何学和啮合性能为基础,搭建电封闭式传动性能试验台,对鼓形蜗杆传动副样机在多工况下进行传动性能测试.测试结果为:由于存在制造误差和装配误差,鼓形蜗杆传动副样机的实际接触区为理论接触区的2/3;鼓形蜗杆传动副样机的传动效率随着转速的提高而增加,在低转速时,传动效率随着负载的增大明显降低;在高转速时,传动效率随着负载的增大而略有升高;鼓形蜗杆传动副样机在各测试工况下的最高传动效率为69.05%,最高油池温升为89.8 ℃;该鼓形蜗杆传动副具有优良的传动性能,适用于重载动力传动.
- 鼓形蜗杆传动 /
- 样机 /
- 传动性能 /
- 测试
Abstract: In order to obtain the transmission performance parameters of the planar internal gear primary-enveloping crown worm drive (hereinafter referred to as crown worm drive), an electrically enclosed transmission performance test rig was built based on the meshing geometry and meshing performance to test the transmission performance of a prototype crown worm drive in various working conditions. The test results show that the actual contact areas are only two thirds of the theoretic contact area because of the manufacture error and assembly error. The transmission efficiency of the crown worm drive increases with the rotational speed increasing: as the load increases, the transmission efficiency decreases significantly at low speed, and presents a slight rise at high speed. In various working conditions, the maximum transmission efficiency is 69.05%, and the maximum temperature rise of box oil is no more than 89.8 ℃. Therefore, the crown worm drive has an excellent transmission performance, and is suitable for heavy power transmission.
- crown worm drive /
- prototype /
- transmission performance /
- testing

HTML全文

参考文献(42)

洛阳矿山机械研究所,徐州矿山设备制造厂. 国际齿轮装置与传递会议论文选

[M]. 北京:机械工业出版社,1984: 327-338.

王进戈. 滚锥包络环面蜗杆传动的研究

万方美. 准平面二次包络环面蜗杆传动的研究

[D]. 重庆:重庆大学,1992.

张光辉. 侧隙可调式平面包络环面蜗杆传动. 中国,CN1257974A

邓星桥,王进戈,张均富,等. 无侧隙双滚子包络环面蜗杆真实啮合齿面的理论研究

王进戈,张均富,邓星桥,等. 无侧隙双滚子包络环面蜗杆传动的参数优化

[D]. 重庆:重庆大学,2001.

孙月海,段路茜,王树人,等. 基于接触线的二次包络TI蜗杆传动啮合性能分析

孙月海,卢华武,杨文彦,等. 硬齿面TI蜗杆副的研制与试验研究

[P]. 2000-06-28.

孙月海,段路茜,王树人,等. 边界条件和螺旋角对TI蜗杆传动啮合性能的影响

KUEHNLE M, PEEKEN H. The toroidal drive

[J]. 西南交通大学学报,2010,45(2): 222-226. DENG Xingqiao, WANG Jinge, ZHANG Junfu, et al. Theoretical study on real tooth surface of non-backlash double-roller enveloping hourglass worm

[J]. Journal of Southwest Jiaotong University, 2010, 45(2): 222-226.

XU Lizhong, HUANG Zhen, YANG Yulin. Contact stress for toroidal drive

XU Lizhong, HUANG Zhen, YANG Yulin. Mesh theory for toroidal drive

[J]. 机械工程学报,2010,46(21): 6-12. WANG Jinge, ZHANG Junfu, DENG Xingqiao, et al. Parameter optimization of the non-backlash double-roller enveloping hourglass worm gearing

陈永洪,张光辉,陈兵奎,等. 平面内齿轮包络凸环面蜗杆传动啮合性能分析

陈永洪,张光辉,陈兵奎,等. 平面内齿包络凸环面蜗杆齿形研究

[J]. Chinese Journal of Mechanical Engineering, 2010, 46(21): 6-12.

张彦钦,张光辉. 平面二次包络环面蜗杆传动强度计算

中华人民共和国国家质量监督检验检疫总局. GB/T16442008 平面二次包络环面蜗杆减速器

[J]. 机械工程学报,2005,41(6): 44-48. SUN Yuehai, DUAN Luqian, WANG Shuren, et al. Contact performance analysis of double enveloping TI worm gearing based on contact lines

DONG Liyang, LIU Pingyi, WEI Wenjun, et al. Study on ZI worm and helical gear drive with large transmission ratio

[J]. Chinese Journal of Mechanical Engineering, 2005, 41(6): 44-48.

[J]. 机械工程学报,2011,47(9): 182-186. SUN Yuehai, LU Huawu, YAN Wenyan, et al. A study on manufacture and experiment of hardened TI worm gearing

[J]. Chinese Journal of Mechanical Engineering, 2011, 47(9): 182-186.

[J]. 天津大学学报,2004,37(10): 918- 922. SUN Yuehai, DUAN Luqian, WANG Shuren, et al. Effects of boundary and helix angle on meshing performance of TI worm gearing

[J]. Chinese Journal of Tianjin University, 2004, 37(10): 918- 922.

[J]. Mechanical Engineering, 1981, 32(2): 32-39.

[J]. Journal of Mechanical Design, 2003, 125(1): 165-168.

[J]. Journal of Mechanical Design, 2004, 126(3): 551-557.

[J]. 重庆大学学报,2012,35(3): 1-7. CHEN Yonghong, ZHANG Guanghui, CHEN Bingkui, et al. Meshing performance analysis of planar internal gear enveloping crown worm drive

[J]. Journal of Chongqing University, 2012, 35(3): 1-7.

[J]. 中国机械工程,2012,23(16): 1891-1896. CHEN Yonghong, ZHANG Guanghui, CHEN Bingkui, et al. Study on tooth profile of planar enveloping crown worm

[J]. China Mechanical Engineering, 2012, 23(16): 1891-1896.

[J]. 西南交通大学学报,2011,46(1): 138-142. ZHANG Yanqin, ZHANG Guanghui. Strength calculation of planar double-enveloping hourglass worm gears

[J]. Journal of Southwest Jiaotong University, 2011, 46(1): 138-142.

[S]. 北京:中国标准出版社,2008.

[J]. Mechanism and Machine Theory, 2014, 74: 299- 309.

施引文献

附加材料(0)

访问统计