| 重载货车车钩准静态受力分析与纵向载荷分配规律 |
| |
| 引用本文： | 朱涛,尹敏轩,徐京涛,王超,肖守讷,阳光武.重载货车车钩准静态受力分析与纵向载荷分配规律[J].交通运输工程学报,2020,20(5):165-175. |
| |
| 作者姓名： | 朱涛 尹敏轩 徐京涛 王超 肖守讷 阳光武 |
| |
| 作者单位： | 西南交通大学 牵引动力国家重点实验室, 四川 成都 610031 |
| |
| 基金项目： | 四川省科技计划;牵引动力国家重点实验室自主研究项目;国家自然科学基金 |
| |
| 摘 要： | 针对重载货车车钩在车钩间隙、重力与纵向牵引力综合作用下的受力状态改变问题, 对车钩进行了准静态受力分析, 研究了其纵向载荷分配规律; 设计了钩舌上下牵引凸缘根部的应变试验, 得到了测点弹性应变随牵引力的变化关系, 分析了上下牵引凸缘承载程度变化趋势; 对车钩进行了详细的受力分析, 推导了载荷传递部位等效力解析解, 得到了车钩承受不同牵引力作用时所对应的仿真边界条件; 对车钩结构进行了仿真分析, 得到了节点应变随牵引力变化的响应曲线, 通过与应变测试试验结果的对比分析, 证明了车钩载荷传递部位等效力解析解和仿真模型的可靠性; 研究了牵引力与钩舌内腕面、上下牵引凸缘等效力的关系式中关键参数对等效力的影响规律。研究结果表明: 当牵引力小于13.5 kN时, 上受压推台受力; 牵引力为13.5~1 725.0 kN时, 车钩系统上下牵引凸缘同时承载, 随着牵引力的逐渐增大, 下牵引凸缘承载比例逐渐减小并趋近于0.53, 上牵引凸缘承载比例逐渐增大并趋近于0.47, 承载比例与系统参数有线性关系, 其中钩舌内腕面等效力作用位置对此影响极大。研究结果作为研究车钩疲劳裂纹萌生和扩展仿真的基础, 对铁路重载车钩服役安全性具有极强的指导意义和参考价值。
|
| 关 键 词： | 车辆工程 重载货车车钩 准静态受力分析 接触状态 纵向载荷分配 仿真分析 |
| 收稿时间： | 2020-05-19 |
Quasi-static force analysis and longitudinal load distribution law of heavy haul freight coupler |
| |
| ZHU Tao,YIN Min-xuan,XU Jing-tao,WANG Chao,XIAO Shou-ne,YANG Guang-wu.Quasi-static force analysis and longitudinal load distribution law of heavy haul freight coupler[J].Journal of Traffic and Transportation Engineering,2020,20(5):165-175. |
| |
| Authors: | ZHU Tao YIN Min-xuan XU Jing-tao WANG Chao XIAO Shou-ne YANG Guang-wu |
| |
| Affiliation: | State Key Laboratory of Traction Power, Southwest Jiaotong University, Chengdu 610031, Sichuan, China |
| |
| Abstract: | To evaluate the change in the force state of a heavy haul freight coupler under the combined action of coupler clearance, gravity, and longitudinal traction force, a quasi-static force analysis for the coupler was carried out and the longitudinal load distribution law was studied. A strain test at the roots of the upper and lower traction flanges of the knuckle was designed. The relationship between the elastic stain of measuring points and traction force was obtained. The change trends of bearing degrees of the upper and lower traction flanges were analyzed. A detailed force analysis of coupler was carried out. An analytical solution of equivalent forces on the load transfer sites was derived. The boundary conditions of the simulation under different traction forces of coupler were obtained. A simulation analysis of coupler was carried out. The response curve of node strain with the traction force was obtained. Through comparison to the results of strain test, the reliabilities of analytical solution of the equivalent forces on the load transfer sites and simulation model were demonstrated. The influences of some key parameters on the relationship between the traction force and equivalent force were analyzed. The equivalent forces refer to the forces acting on the inner wrist surface and upper and lower traction flanges. Research result shows that the upper shocking platform is stressed when the traction force is smaller than 13.5 kN. The upper and lower traction flanges of the coupler are loaded simultaneously when the traction force is 13.5-1 725.0 kN. With the gradual increase in the traction force, the bearing ratio of lower traction flange gradually decreases and approaches 0.53, while the bearing ratio of upper traction flange increases and approaches 0.47. The bearing ratio is linear with respect to the system parameters. The acting position of equivalent force on the inner wrist surface of knuckle has a large influence on it. These results can be used as a basis for studying the fatigue crack initiation and propagation simulations of couplers and have a high guiding significance for the couplers' service safety. |
| |
| Keywords: | |
| 本文献已被 万方数据 等数据库收录！ |
| 点击此处可从《交通运输工程学报》浏览原始摘要信息 |
|
点击此处可从《交通运输工程学报》下载全文 |
|
