船舶结构用铝—钛—钢复合过渡接头疲劳性能研究

铝－钛－钢爆炸复合板作为新型舰船结构铝合金，钢之间连接过渡接头取代传统的铆接连接具有优越的连接性能和施工工艺。本研究模拟实际应用条件，测定了其焊接前后在固定应力水平下的弯曲疲劳寿命和弯曲疲劳Ｓ－Ｎ曲线，并运用计算机得到Ｓ－Ｎ曲线的回归方程，为复合过渡接头疲劳寿命的预测和最大应力的控制等提供了依据。     

超声冲击法改善高强钢焊接接头的疲劳性能

焊接接头的疲劳强度远低于母材 ,大量试验表明疲劳裂纹主要起源于接头焊趾处。使用超声冲击法处理接头 ,以改变焊趾区几何形状、消除焊趾缺陷、调整焊趾区残余应力场 ,是改善焊接接头及结构疲劳强度的一种有效方法。利用自行研制的超声冲击装置 ,采用两种接头形式 (纵向角接接头和对接接头 )进行了 SS80 0高强钢原始焊态与超声冲击处理态的疲劳对比试验 ,结果表明 :( 1 )双面焊对接接头焊态试件的疲劳强度Δσ ( 2× 1 0 6 )为 1 5 0 MPa;单面焊对接焊态试件的疲劳强度Δσ ( 2× 1 0 6 )为 1 3 2 MPa;纵向角接焊态试件的疲劳强度Δσ ( 2× 1 0 6 )为 98MPa。 ( 2 )超声冲击处理态单面焊双面成型试件与原始焊态试件相比 ,疲劳强度提高 1 3 2 %左右 ,疲劳寿命延长了 48～ 1 3 2倍 ;双面焊接对接超声冲击处理态试件与原始焊态试件相比 ,疲劳强度提高95 %左右 ,疲劳寿命延长了 2 2～ 62倍 ;纵向角接接头超声冲击处理试件与原始焊态试件相比 ,疲劳强度提高1 73 %左右 ,疲劳寿命延长了 3 2～ 70倍。 ( 3 )超声冲击处理技术能够大幅度改善高强钢焊接接头的疲劳性能     

AH32钢T型焊接接头疲劳强度的试验与数值模拟

对AH32钢T型试件进行疲劳试验,并利用有限元软件对T型焊接接头的应力分布及疲劳寿命进行数值模拟,最终将疲劳试验结果与数值模拟结果对比分析。研究发现,T型焊接接头在焊趾附近处应力值最大,寿命最短。本文研究结果为今后船海结构物的疲劳寿命预测提供了有益参考。     

双平衡环挠性陀螺接头疲劳寿命的可靠性预计

本文以一种双平衡环挠性陀螺接头为结构模型,运用可靠性方法对挠性接头的疲劳寿命进行了分析,提出了一种预计挠性接头对于无限寿命的可靠度的方法。     

铝镁合金焊接接头疲劳性能研究

本文依据船体结构及其受力特点，提出了四种焊接接头试样，测定了ＬＦ１５、ＬＦ１６两种铝镁合金焊接接头疲劳性能，研究了结构因素及焊接缺陷对疲劳性能的影响，取得了较系统的疲劳性能研究结果，为铝船体的结构设计、疲劳强度估算、焊接工艺制定以及船体施工等提供了可靠的依据。     

DH36钢趾端焊接接头低温疲劳试验研究

常温S-N曲线无法满足极地低温环境下船海结构疲劳设计的需要,开展了-60℃条件下的船用DH36钢焊接接头低温疲劳强度试验研究。根据国标准设计DH36钢趾端焊接接头的疲劳标准试件,将试件放置在低温箱内采用热点应力方法进行疲劳热点应力测试,并与有限元计算结果进行对比分析,验证了试验测量的可靠性。试验共测量了两级应力范围水平,每级应力范围水平测量14个试件,基于测得的热点应力范围及疲劳寿命,利用单侧容限系数法得到了不同存活率下的p-S-N曲线,结果表明,低温条件下疲劳寿命符合对数正态分布,低温疲劳寿命高于常温疲劳寿命。     

新型立式铝-钢复合接头焊后性能实验研究

本文通过对新型立式铝—钢复合接头焊接后的抗拉强度、疲劳性能、抗冲击性能等实验研究，得出了新型立式铝—钢复合接头焊接后在力学性能上满足工程应用要求的结论。     

打磨处理改善焊缝疲劳性能的试验研究

由于高强度钢的使用，船舶结构许用应力水平的提高，船舶结构的疲劳强度越来越受到关注。船舶结构的疲劳寿命取决于其焊接结构的疲劳寿命。因此，了解焊缝几何参数对焊件疲劳强度的影响以及采用经济实用的方法改善船舶结构的疲劳性能是十分重要的。本文首先对焊缝几何参数对焊件疲劳寿命的影响进行了分析，在此基础上用ABS钢和945钢两种钢板做试件，分别进行了简单拉伸实验及打磨和未打磨条件下对接接头的疲劳试验。试验结果表明焊件的疲劳寿命可以通过打磨焊缝得到改善；尤其对于高强度钢焊件。试验还说明手工打磨焊缝和机械磨削焊缝对焊件疲劳强度的改善效果差别很大，疲劳寿命的分散性也很大。因此，应当对改善焊件疲劳寿命的工艺进行更详细的研究。     

焊接结构多轴疲劳寿命预测结构应力法

海洋工程焊接结构形式复杂且遭受随机波浪载荷作用,焊接接头多数处于多轴疲劳状态,而目前工程上主要采用基于单轴疲劳理论和试验的方法预测结构的疲劳寿命。为了提高焊接结构疲劳寿命预测的准确性,文章提出了一种评估焊接接头疲劳强度的新型结构应力法,并与临界面理论相结合,能够用于实际焊接结构的多轴疲劳寿命预测。通过对国际上已公开发表的疲劳试验数据进行有限元分析,证明了文中提出的结构应力法比传统的热点应力法具有更高的精度,以及该方法应用于焊接结构多轴疲劳寿命预测的可行性。最后,应用该方法对一个T型管节点进行了多轴疲劳寿命计算。     

船用钢T型接头焊趾选择优化研究

针对船体焊接构件焊趾处应力集中影响船艇结构寿命的问题,利用有限元软件建立船艇重要区域中内龙骨的有限元模型,在约束和载荷相同的情况下,对比分析不同焊趾形式及尺寸T型接头的应力分布和疲劳寿命。研究表明,对于陆军船艇而言,平面形焊趾形式应力集中程度较小,焊后加工方便,适合船艇修理实际要求;焊脚尺寸为4~6 mm的平面形焊趾形式的T型接头疲劳寿命最大,在船艇T型构件焊接时焊脚尺寸应选用此范围内。     

Weld toe versus root fatigue failure mode and governing parameters: A study of aluminum alloy load-carrying fillet joints

In load-carrying fillet welded connections, two fatigue failure modes are possible i.e. weld toe cracking and weld root cracking. The fatigue life associated with weld root cracking is typically much lower than weld toe cracking, exhibiting a wider scatter band, especially for welded aluminum alloys. This paper examines fatigue failure mode transition behaviors in load-carrying fillet welds made of aluminum and their governing parameters, among plate thickness, weld penetration, joint misalignment, weld material, and ultrasound impact peening(UIP). Through both experimental and theoretical studies, a quantitative fillet weld sizing criterion was proposed for avoiding weld root cracking in fillet-welded aluminum connections.     

Stress magnification effect of initial deformation on the notch stress field and fatigue strength of thin plate welded joints

Compared with thick plate welded joint, the welding joint of thin plate will produce initial deformation due to its low bending rigidity. The existence of initial deformation will cause the welded structure to produce secondary bending effect, which will produce greater stress magnification effect at the weld toe and seriously affect the fatigue strength of thin plate welded joints. Therefore, based on the correction formula of thick plate, considering the influence of initial deformation and geometric nonlinearity of thin plate, this paper deduces the stress magnification factor formula at the weld toe of T-shaped and cruciform specimens. The accuracy of the revised formula is further verified by comparing the notch stress calculated by the modified formula with the FE results. Finally, the modified formula is applied to the notch stress and fatigue evaluation of typical thin plate welded joints respectively. The results show that the proposed notch stress calculation formula can fully consider the stress amplification effect of thin plate structure, and can be used to quickly evaluate the notch stress field and fatigue strength of thin plate welded joints.     

T型接头焊趾表面裂纹应力强度因子的简化计算方法

T型接头是船舶与海洋结构物的典型结构形式之一,其焊趾处常常是疲劳热点区域。T型接头焊趾表面裂纹的应力强度因子是船舶与海洋结构的、基于断裂力学安全评定和疲劳寿命预测的基础。本文对T型接头表面裂纹应力强度因子的计算方法,尤其是Bow ness等人提出的T型接头焊趾表面裂纹应力强度因子的计算公式进行了分析,在此基础上导出了形式简单,物理意义明确的T型接头焊趾表面裂纹应力强度因子的简化计算公式,并和相关的应力强度因子的计算结果进行了比较,证明了本文简化方法的可行性。     

T型焊接接头疲劳性能研究

T型焊接接头在船舶与海洋工程结构中广泛应用,研究T型焊接接头的疲劳性能对于提高船舶与海洋工程结构的强度具有重要意义.针对工程中常用的四种焊趾形式的T型焊接接头,利用有限元计算和模型试验两种方法对其疲劳性能进行了研究.结果表明,平面型焊趾是较优的T型接头焊趾形式.     

铝合金表面状态对搅拌摩擦焊接头组织和性能的影响

研究了铝合金表面状态对搅拌摩擦焊焊接接头组织和性能的影响。试验结果表明:试板表面油污的存在使得焊接接头强度下降为母材的60%左右,同时显著降低接头的塑性;试板表面的氧化膜和油污还会造成焊核区及焊缝前进侧的残余间混结合线缺陷。对焊接接头拉伸断口进行扫描电镜观察发现:拉伸试样的断口中存在油污和A l2O3的聚集物,这些聚集物会成为拉伸时的裂纹源。断口和力学性能综合分析表明:铝合金表面的油污和氧化膜都会降低搅拌摩擦焊接头的强度和塑性。     

岸边集装箱桥式起重机撑管封板疲劳开裂分析

为探究岸边集装箱桥式起重机撑管封板受载情况和焊缝危险位置的疲劳寿命,对65 t/60 m岸边集装箱桥式起重机的典型载荷工况进行分析。计算门框上水平撑管的疲劳载荷幅值,研究撑管封板焊缝的受载情况,应用S-N曲线法计算焊缝的结构应力并分析焊缝危险位置的疲劳寿命。结果表明,最大von Mises应力出现在封板与节点板端部角焊缝的焊趾上。封板焊缝危险部位的疲劳寿命无法满足岸边集装箱桥式起重机安全服役30 a的要求。     

A design method of tensile triangles and low transformation temperature weld metal for reduction of stress concentration and residual stress of welded joints

Stress concentration and residual stress have a significant influence on fatigue life of welded joints. In order to reduce the stress concentration of welded joints, a mathematical design method of tensile triangles (MTT) based on bionics was applied to weld shape design. Accordingly, the stress concentration of various weld beads in the corner boxing welded joint and the fillet welded T-joint was dissected using our in-house FEM software JWRIAN. It was found that there existed a large stress concentration in the conventional welded joints, whereas those welded joints with elongated weld bead were accompanied by a lower stress concentration, especially for elongated weld bead with MTT design. Furthermore, among the weld shapes of the corner boxing fillet welded joint, the rectangle shape of weld bead had the minimum stress concentration factor (1.05). For the fillet welded T-joint with MTT design, the stress concentration of weld toe decreased dramatically with the increase of the index of designed shape, but there was a minor difference of stress concentration at weld root between the weld beads with MTT design. In addition, application of low transformation temperature (LTT) weld metal utilizing martensitic transformation to the fillet welded T-joints can produce compressive residual stress at weld toe.     

Stress analysis of a transversely loaded aluminum weldment

The analysis of welded structural details is an important component in determining life cycle estimates. As part of a project to develop guidelines for reducing cracks in aluminum ship structures, the authors performed experiments showing that the stress levels developed strongly depend on the welded connection details. To properly quantify the effects of connection details, a stress analysis of the detail is required. This investigation summarizes the analysis of a common structural detail, one that results in a transversely loaded weldment.This paper is motivated by two sets of experimental test results. The first is the stress concentration observed at the intersection of the longitudinal and transverse members in a 1.5-m×3-m aluminum bottom panel tested under uniform pressure loading. The second is the reduction in fatigue life due to weld geometry variations between manually welded and machine-welded aluminum specimens. In order to clarify these two observations, the authors completed a detailed finite element analysis of a welded aluminum T-stiffener. The results show a significant stress concentration in the weld toe area. This stress concentration is shown to be strongly dependent on the weld toe geometry.     

焊趾表面裂纹应力强度因子简化计算的比较研究

对接、T型接头与十字接头是船舶与海洋结构的典型结构形式,其大部分疲劳失效是由于焊趾引起的.各种表面裂纹的应力强度因子计算是船舶与海洋结构基于断裂力学安全评定和疲劳寿命预测的基础.Bowness等人提出了T型接头焊趾表面裂纹应力强度因子计算式,作者对其复杂的计算式进行了简化.BS7910针对对接、T型接头与十字接头提出了两套焊趾应力强度因子表达式,一是针对二维表面裂纹提出的,一是针对三维表面裂纹提出的.本文对作者给出的简化表达式以及BS7910的两套表达式进行了比较.结果表明作者给出的简化表达式不仅可以用来计算T型接头的焊趾表面裂纹应力强度因子,而且可以用来计算对接与十字接头焊趾表面裂纹的应力强度因子.同时发现在a/T＜0.05处三者的差别比较大,因此用有限元法进行了验证,结果证明作者给出的简化表达式比其他表达式更加合理.