基于神经网络的无信号路口人车交通行为预测分析

以无信号灯路口人车交通行为为研究对象,对行人和机动车辆在无信号灯路口的整体交通行为进行分类预测。在对路口现场交通情况进行拍摄后,用电脑的分帧技术对所需要的数据进行提取和分类,而后建立BP神经网络模型,确定神经网络的输入变量与输出变量。将样本数据导入神经网络并进行训练和测试后,得出行人和车辆过街类型的分类准确率,并且通过准确率所达到的标准来证明了BP神经网络模型的可行性。     

Specification and calibration of a microscopic model for pedestrian dynamic simulation at signalized intersections: A hybrid approach

Macroscopic pedestrian models for bidirectional flow analysis encounter limitations in describing microscopic dynamics at crosswalks. Pedestrian behavior at crosswalks is typically characterized by the evasive effect with conflicting pedestrians and vehicles and the following effect with leading pedestrians. This study proposes a hybrid approach (i.e., route search and social force-based approach) for modeling of pedestrian movement at signalized crosswalks. The key influential factors, i.e., leading pedestrians, conflict with opposite pedestrians, collision avoidance with vehicles, and compromise with traffic lights, are considered. Aerial video data collected at one intersection in Beijing, China were recorded and extracted. A new calibration approach based on a genetic algorithm is proposed that enables optimization of the relative error of pedestrian trajectory in two dimensions, i.e., moving distance and angle. Model validation is conducted by comparison with the observed trajectories in five typical cases of pedestrian crossing with or without conflict between pedestrians and vehicles. The characteristics of pedestrian flow, speed, acceleration, pedestrian-vehicle conflict, and the lane formation phenomenon were compared with those from two competitive models, thus demonstrating the advantage of the proposed model.     

Microscopic modeling of large‐scale pedestrian–vehicle conflicts in the city of Madinah,Saudi Arabia

This paper presents a micro‐simulation modeling framework for evaluating pedestrian–vehicle conflicts in crowded crossing areas. The framework adopts a simulation approach that models vehicles and pedestrians at the microscopic level while satisfying two sets of constraints: (1) flow constraints and (2) non‐collision constraints. Pedestrians move across two‐directional cells as opposed to one‐dimensional lanes as in the case of vehicles; therefore, extra caution is considered when modeling the shared space between vehicles and pedestrians. The framework is used to assess large‐scale pedestrian–vehicle conflicts in a highly congested ring road in the City of Madinah that carries 20 000 vehicles/hour and crossed by 140 000 pedestrians/hour after a major congregational prayer. The quantitative and visual results of the simulation exhibits serious conflicts between pedestrians and vehicles, resulting in considerable delays for pedestrians crossing the road (9 minutes average delay) and slow traffic conditions (average speed <10 km/hour). The model is then used to evaluate the following three mitigating strategies: (1) pedestrian‐only phase; (2) grade separation; and (3) pedestrian mall. A matrix of operational measures of effectiveness for network‐wide performance (e.g., average travel time, average speed) and for pedestrian‐specific performance (e.g., mean speed, mean density, mean delay, mean moving time) is used to assess the effectiveness of the proposed strategies. Copyright © 2012 John Wiley & Sons, Ltd.     

A dynamic evacuation model for pedestrian–vehicle mixed-flow networks

In urban emergency evacuation, a potentially large number of evacuees may depend either on transit or other modes, or need to walk a long distance, to access their passenger cars. In the process of approaching the designated pick-up points or parking areas for evacuation, the massive number of pedestrians may cause tremendous burden to vehicles in the roadway network. Responsible agencies often need to contend with congestion incurred by massive vehicles emanating from parking garages, evacuation buses generated from bus stops, and the conflicts between evacuees and vehicles at intersections. Hence, an effective plan for such evacuation needs to concurrently address both the multi-modal traffic route assignment and the optimization of network signal controls for mixed traffic flows. This paper presents an integrated model to produce the optimal distribution of vehicle and pedestrian flows, and the responsive network signal plan for massive mixed pedestrian–vehicle flows within the evacuation zone. The proposed model features its effectiveness in accounting for multiple types of evacuation vehicles, the interdependent relations between pedestrian and vehicle flows via some conversion locations, and the inevitable conflicts between intersection turning vehicle and pedestrian flows. An illustrating example concerning an evacuation around the M&T stadium area has been presented, and the results indicate the promising properties of our proposed model, especially on reflecting the complex interactions between vehicle and pedestrian flows and the favorable use of high-occupancy vehicles for evacuation operations.     

A model of pedestrians’ intended waiting times for street crossings at signalized intersections

For the purposes of both traffic-light control and the design of roadway layouts, it is important to understand pedestrian street-crossing behavior because it is not only crucial for improving pedestrian safety but also helps to optimize vehicle flow. This paper explores the mechanism of pedestrian street crossings during the red-man phase of traffic light signals and proposes a model for pedestrians’ waiting times at signalized intersections. We start from a simplified scenario for a particular pedestrian under specific traffic conditions. Then we take into account the interaction between vehicles and pedestrians via statistical unconditioning. We show that this in general leads to a U-shaped distribution of the pedestrians’ intended waiting time. This U-shaped distribution characterizes the nature of pedestrian street-crossing behavior, showing that in general there are a large proportion of pedestrians who cross the street immediately after arriving at the crossing point, and a large proportion of pedestrians who are willing to wait for the entire red-man phase. The U-shaped distribution is shown to reduce to a J-shaped or L-shaped distribution for certain traffic scenarios. The proposed statistical model was applied to analyze real field data.     

Multi-modal traffic signal control with priority,signal actuation and coordination

Both coordinated-actuated signal control systems and signal priority control systems have been widely deployed for the last few decades. However, these two control systems are often conflicting with each due to different control objectives. This paper aims to address the conflicting issues between actuated-coordination and multi-modal priority control. Enabled by vehicle-to-infrastructure (v2i) communication in Connected Vehicle Systems, priority eligible vehicles, such as emergency vehicles, transit buses, commercial trucks, and pedestrians are able to send request for priority messages to a traffic signal controller when approaching a signalized intersection. It is likely that multiple vehicles and pedestrians will send requests such that there may be multiple active requests at the same time. A request-based mixed-integer linear program (MILP) is formulated that explicitly accommodate multiple priority requests from different modes of vehicles and pedestrians while simultaneously considering coordination and vehicle actuation. Signal coordination is achieved by integrating virtual coordination requests for priority in the formulation. A penalty is added to the objective function when the signal coordination is not fulfilled. This “soft” signal coordination allows the signal plan to adjust itself to serve multiple priority requests that may be from different modes. The priority-optimal signal timing is responsive to real-time actuations of non-priority demand by allowing phases to extend and gap out using traditional vehicle actuation logic. The proposed control method is compared with state-of-practice transit signal priority (TSP) both under the optimized signal timing plans using microscopic traffic simulation. The simulation experiments show that the proposed control model is able to reduce average bus delay, average pedestrian delay, and average passenger car delay, especially for highly congested condition with a high frequency of transit vehicle priority requests.     

Evaluating effects of traffic and vehicle characteristics on vehicular emissions near traffic intersections

Urban air quality is generally poor at traffic intersections due to variations in vehicles’ speeds as they approach and leave. This paper examines the effect of traffic, vehicle and road characteristics on vehicular emissions with a view to understand a link between emissions and the most likely influencing and measurable characteristics. It demonstrates the relationships of traffic, vehicle and intersection characteristics with vehicular exhaust emissions and reviews the traffic flow and emission models. Most studies have found that vehicular exhaust emissions near traffic intersections are largely dependent on fleet speed, deceleration speed, queuing time in idle mode with a red signal time, acceleration speed, queue length, traffic-flow rate and ambient conditions. The vehicular composition also affects emissions. These parameters can be quantified and incorporated into the emission models. There is no validated methodology to quantify some non-measurable parameters such as driving behaviour, pedestrian activity, and road conditions     

The use of gait parameters to evaluate pedestrian behavior at scramble phase signalized intersections

Pedestrian scramble phasing is usually implemented to reduce pedestrian‐vehicle conflicts and therefore increase the safety of the intersection. However, to adequately determine the benefits of scramble phasing, it is necessary to understand how pedestrians react to such an unconventional design. This study investigates changes in pedestrian crossing behavior following the implementation of a scramble phase by examining the spatiotemporal gait parameters (step length and step frequency). This detailed microscopic‐level analysis provides insight into changes in pedestrian walking mechanisms as well as the effect of various pedestrian and intersection characteristics. The study uses video data collected at a scramble phase signalized intersection in Oakland, California. Gait parameters were found to be influenced by pedestrian gender, age, group size, crosswalk length, and pedestrian signal indications. Both average step length and walking speed were significantly higher for diagonally crossing pedestrians compared with pedestrians crossing on the conventional crosswalks. Pedestrians were found to have the tendency to increase their step length more than their step frequency to increase walking speed. It was also found that, compared with men, women generally increase their walking speed by increasing their step frequency more than step length. However, when in non‐compliance with signal indications, women increase their walking speed by increasing their step length more than step frequency. It was also found that older pedestrians do not significantly change their walking behavior when in non‐compliance with signal indications. Copyright © 2014 John Wiley & Sons, Ltd.     

Pedestrian gap acceptance for mid-block street crossing

Abstract

This paper investigates pedestrians' traffic gap acceptance for mid-block street crossing in urban areas. A field survey was carried out at an uncontrolled mid-block location in Athens, Greece. Pedestrians' decisions and traffic conditions were videotaped in terms of the size of traffic gaps rejected or accepted, waiting times and crossing attempts and vehicle speeds. A lognormal regression model was developed to examine pedestrian gap acceptance. It was found that gap acceptance was better explained by the distance from the incoming vehicle, rather than its speed. Other significant effects included illegal parking, presence of other pedestrians and incoming vehicles’ size. A binary logistic regression model was developed to examine the effect of traffic gaps and other parameters on pedestrians' decisions to cross the street or not. The results reveal that this decision is affected by the distance from the incoming vehicles and the waiting times of pedestrians.     

Impacts of driving patterns on tank-to-wheel energy use of plug-in hybrid electric vehicles

We evaluate the implications of a range of driving patterns on the tank-to-wheel energy use of plug-in hybrid electric vehicles. The driving patterns, which reflect short distance, low speed, and congested city driving to long distance, high speed, and uncongested highway driving, are estimated using an approach that involves linked traffic assignment and vehicle motion models. We find substantial variation in tank-to-wheel energy use of plug-in hybrid electric vehicles across driving patterns. Tank-to-wheel petroleum energy use on a per kilometer basis is lowest for the city and highest for the highway driving, with the opposite holding for a conventional internal combustion engine vehicle.     

Developments of CO2-emissions and costs for small electric and combustion engine vehicles in Germany

Electric vehicles have the potential to lower emissions in the mobility sector, but especially high costs might hinder their market development. This paper aims to access environmental and economic impacts and potentials by comparing CO₂-emissions and costs of small vehicles. Considering actual data it is analysed, if and under which conditions electric vehicles are financially competitive for private consumers and under which conditions emissions can be saved. For this, a multiple-stage approach is focusing on (1) emissions during production and operation, (2) private costs and (3) external costs of emissions. A model of total cost of ownership is applied for the analysis of private and external costs.Results show that emissions of electric vehicles exceed emissions of combustion engine vehicles in the production phase, but electric vehicles cause fewer emissions during operation. Total emissions can be saved by electric vehicles even with low annual driving distances (2500–5500 km/a today). Results highly depend on the form of electricity production.Today, private costs of electric vehicles exceed the costs of combustion engine vehicles. Due to cost decreases electric vehicles can gain financial advantages in the future. External costs are high, especially for combustion engine vehicles (up to 15% of private costs), but in none of the considered cases high enough to give electric vehicles a financial advantage today. This picture will change in the future.     

Acceptability of audible pedestrian signal noise

This paper considers the impact on local residents of audible pedestrian signals (APS) that provide cues to the visually handicapped pedestrians on the onset of the various signal phases at a signalized crosswalk. We investigate the extent of the noise intrusion problem of APS through understanding the acceptability by the general public. From the perception surveys conducted, vehicle engine/braking sound, neighbor talking/playing and vehicle alarm are the top three irritating noises experienced while sleeping whereas audible signals is ranked at 21st position. The maximum sound level of the signals found to be acceptable indoors is close to 60 dBA.     

Multi-objective signal control of urban junctions – Framework and a London case study

This paper presents an approach to multi-objective signal control using fuzzy logic. The signal control uses fuzzy logic where the membership functions are optimised according to the Bellman–Zadeh principle of fuzzy decision-making. This approach is both practical for the decision-maker and efficient, as it leads directly to a Pareto-optimal solution. Signal control priorities are ultimately a political decision. Therefore the tool developed in this research allows the traffic engineer to balance the objectives easily by setting acceptability and unacceptability thresholds for each objective. Particular attention is given in the example to pedestrian delays. The membership functions of the fuzzy logic are optimised by a genetic algorithm coupled to the VISSIM microscopic traffic simulator. The concept is illustrated with a case study of the Marylebone Road–Baker Street intersection in London at which pedestrians as well as vehicle flows are high. The results prove the feasibility of the framework and show the vehicle delays for a more pedestrian friendly signal control strategy.     

Evaluation of pedestrian crosswalk level of service (LOS) in perspective of type of land-use

In India pedestrians usually cross the road at mid-block crosswalks due to ease of access to their destination or the development of adjacent land use types such as shopping, business areas, school and residential areas. The behaviour of pedestrian will change with respect to different land use type and this change in behaviour of pedestrian further reflects change in perceived level of service (LOS). So, it is important to evaluate the quality of service of such crossing facilities with respect to different land-use type under mixed traffic conditions. In this framework, pedestrian perceived LOS were collected with respect to different land-use type such as shopping, residential and business areas. The ordered probit (OP) model was developed by using NLOGIT software package, with number of vehicles encountered, road crossing difficulty as well as safety considered as primary factors along with pedestrian individual factors (gender and age), land-use type and roadway geometry. From the model results, it has been concluded that perceived safety, crossing difficulty, land-use condition, number of vehicles encountered, median width and number of lanes have significant effect on pedestrian perceived LOS at unprotected (un-signalized) mid-block crosswalks in mixed traffic scenario. The inferences of these results highlights the importance of land use planning in designing a new set of pedestrian access facilities for unprotected mid-block crosswalks under mixed traffic conditions. Also the study results would be useful for evaluating pedestrian accessibility taking into account different land-use type and planning required degree of segregation with vehicular movement at unprotected mid-block crosswalk locations.     

Prohibited–permitted right-turn phasing strategy based on capacity analysis of right-turn movements

In traffic-crowded metropolitan areas, such as Shanghai and Beijing in China, right-turn vehicles that operate with a permitted phase at signalized intersections are normally permitted to filter through large numbers of pedestrians and bicycles. To alleviate such conflicts and improve safety, traffic engineers in Shanghai introduced a prohibited–permitted right-turn operation, adding a subphase to the permitted phase in which right-turns are prohibited. Unfortunately, the prohibited subphase would reduce the capacity of right-turn movements when it prohibits right turns even if there are few pedestrians and bicycles crossing the street. This paper aims at quantifying the impact of both non-vehicular flows and the prohibited subphase on the right-turn capacity, and then proposes a strategy to determine appropriate prohibited–permitted right-turn operation that minimizes the capacity reduction caused by the prohibited subphase. To achieve this goal, we improved the pedestrian and bicycle adjustment factor described in the Highway Capacity Manual by taking into account: (1) the variety in space competition between pedestrians and bicycles, and (2) the effect of two conflict zones in each phase on right-turn operation. In addition, we revised the capacity estimation model in the Highway Capacity Manual, and developed a model based on bicycle/pedestrian volume fluctuation to describe the capacity reduction due to both non-vehicular flows and the prohibited subphase. Furthermore, we proposed a timing strategy for the onset and duration of appropriate prohibited subphase. When bicycle and pedestrian volumes are low, the actuated strategy turns to the permitted phase. When these volumes are moderate, the strategy turns to the prohibited–permitted operation. With the volumes increasing, the prohibited subphase onset advances and duration increases. In these two scenarios, the new strategy has higher right-turn capacity than the current pretimed prohibited–permitted operation. Unfortunately, when bicycle and pedestrian volumes are high, the strategy yields similar right-turn capacity. However, the new prohibited subphase has less potential vehicle–bicycle and vehicle–pedestrian conflicts.     

Modeling pedestrians’ road crossing behavior in traffic system micro-simulation in China

In many Chinese cities, pedestrian’s road crossing behavior is different from that of pedestrians in developed countries. This paper presents a pedestrian model for traffic system micro-simulation in China. Considering the high rate of signal non-compliance, we classify pedestrians into two types: law-obeying ones and opportunistic ones. Opportunistic ones decide whether to violate traffic signal during red man, depending on the states of some external factors (like policeman, vehicle flow and other pedestrians’ behaviors). Questionnaires were used to determine the proportions of these two types of pedestrians under different circumstances. In addition, a time gap distribution extracted from videotape were used to determine the criterion for pedestrians to decide whether to walk or wait when they conflict with vehicle flows. However, simulation results deviate from the data extracted from videotape in some degree. By adjusting the parameters on the basis of analyzing the occurrence of the deviations, the simulation results agree with the field results better. This model has represented the high rate of pedestrians’ red light running and the mixed characteristics of traffic flows in Chinese cities, and it may be applicable in the micro-simulation of traffic system in other developing cities.     

Investigating the applicability of exclusive pedestrian phase at two‐phase actuated controlled intersections

The exclusive pedestrian phase (EPP) has been used in many countries to promote walking around downtown areas by increasing the ease and convenience of pedestrian crossing. However, its applicability has not been systematically demonstrated, especially when an intersection is operated in actuated mode. This paper presents an extensive simulation‐based analysis of the applicability of EPP as compared with a normal concurrent pedestrian‐phase pattern at an isolated intersection controlled by actuated logic. Actuated signal control logics for EPP‐actuated and conventional concurrent pedestrian phase‐actuated controls are developed. Both of these control logics consider pedestrian crossing demands and can adapt to changes in vehicle traffic to reduce vehicle delay as well. A simulation model of a two‐phase controlled intersection is built and calibrated based on field data using VISSIM (PTV Planung Transport Verkehr AG in Karlsruhe, Germany). Extensive analysis is conducted to reveal fully the applicable EPP domain in terms of vehicle traffic demand, pedestrian demand, vehicle turning ratio, and pedestrian diagonal crossing ratio. The results show that the performance and applicable domain of EPP are jointly determined by those five factors. EPP significantly outperforms concurrent pedestrian phase if the vehicle turning ratio is greater than 0.6 and the pedestrian diagonal crossing ratio is greater than 0.6. These results can help traffic engineers in choosing the appropriate pedestrian‐phase patterns at actuated signalized intersections. Copyright © 2015 John Wiley & Sons, Ltd.     

The growing gap in pedestrian and cyclist fatality rates between the United States and the United Kingdom,Germany, Denmark,and the Netherlands, 1990–2018

ABSTRACT

Using official national data for each country, this article calculates trends in walking and cycling fatalities per capita and per km in the USA, the UK, Germany, the Netherlands, and Denmark. From 1990 to 2018, pedestrian fatalities per capita fell by 23% in the USA vs. 66%–80% in the other countries; cyclist fatalities per capita fell by 22% in the USA vs. 55%–68% in the other countries. In 2018, pedestrian fatality rates per km in the USA were 5–10 times higher than in the other four countries; cyclist fatality rates per km in the USA were 4–7 times higher. The gap in walking and cycling fatality rates between the USA and the other countries increased over the entire 28-year period, but especially from 2010 to 2018. Over that 8-year period, per-capita fatality rates in the USA rose by 19% for pedestrians and 11% for cyclists; per-km fatality rates rose by 17% for pedestrians and 33% for cyclists. By comparison, fatality rates either fell or remained stable in the four European countries. We reviewed the relevant literature to identify factors that might help explain the much lower walking and cycling fatality rates in Europe compared to the USA. Possible explanatory factors include better walking and cycling infrastructure; lower urban speed limits; fewer vehicle km travelled; smaller and less powerful personal motor vehicles; and better traffic training, testing, and enforcement of traffic regulations. We recommend that the USA consider implementing an integrated package of mutually reinforcing safety measures such as those that have been successfully implemented in the Netherlands, Denmark, and Germany to reduce pedestrian and cyclist fatality rates.     

A real-time adaptive signal control in a connected vehicle environment

The state of the practice traffic signal control strategies mainly rely on infrastructure based vehicle detector data as the input for the control logic. The infrastructure based detectors are generally point detectors which cannot directly provide measurement of vehicle location and speed. With the advances in wireless communication technology, vehicles are able to communicate with each other and with the infrastructure in the emerging connected vehicle system. Data collected from connected vehicles provides a much more complete picture of the traffic states near an intersection and can be utilized for signal control. This paper presents a real-time adaptive signal phase allocation algorithm using connected vehicle data. The proposed algorithm optimizes the phase sequence and duration by solving a two-level optimization problem. Two objective functions are considered: minimization of total vehicle delay and minimization of queue length. Due to the low penetration rate of the connected vehicles, an algorithm that estimates the states of unequipped vehicle based on connected vehicle data is developed to construct a complete arrival table for the phase allocation algorithm. A real-world intersection is modeled in VISSIM to validate the algorithms. Results with a variety of connected vehicle market penetration rates and demand levels are compared to well-tuned fully actuated control. In general, the proposed control algorithm outperforms actuated control by reducing total delay by as much as 16.33% in a high penetration rate case and similar delay in a low penetration rate case. Different objective functions result in different behaviors of signal timing. The minimization of total vehicle delay usually generates lower total vehicle delay, while minimization of queue length serves all phases in a more balanced way.     

Fuel economy improvements for urban driving: Hybrid vs. intelligent vehicles

The quest for more fuel-efficient vehicles is being driven by the increasing price of oil. Hybrid electric powertrains have established a presence in the marketplace primarily based on the promise of fuel savings through the use of an electric motor in place of the internal combustion engine during different stages of driving. However, these fuel savings associated with hybrid vehicle operation come at the tradeoff of a significantly increased initial vehicle cost due to the increased complexity of the powertrain. On the other hand, telematics-enabled vehicles may use a relatively cheap sensor network to develop information about the traffic environment in which they are operating, and subsequently adjust their drive cycle to improve fuel economy based on this information – thereby representing ‘intelligent’ use of existing powertrain technology to reduce fuel consumption. In this paper, hybrid and intelligent technologies using different amounts of traffic flow information are compared in terms of fuel economy over common urban drive cycles. In order to develop a fair comparison between the technologies, an optimal (for urban driving) hybrid vehicle that matches the performance characteristics of the baseline intelligent vehicle is used. The fuel economy of the optimal hybrid is found to have an average of 20% improvement relative to the baseline vehicle across three different urban drive cycles. Feedforward information about traffic flow supplied by telematics capability is then used to develop alternative driving cycles firstly under the assumption there are no constraints on the intelligent vehicle’s path, and then taking into account in the presence of ‘un-intelligent’ vehicles on the road. It is observed that with telematic capability, the fuel economy improvements equal that achievable with a hybrid configuration with as little as 7 s traffic look-ahead capability, and can be as great as 33% improvement relative to the un-intelligent baseline drivetrain. As a final investigation, the two technologies are combined and the potential for using feedforward information from a sensor network with a hybrid drivetrain is discussed.