Platoons of connected vehicles can double throughput in urban roads

Intersections are the bottlenecks of the urban road system because an intersection’s capacity is only a fraction of the maximum flows that the roads connecting to the intersection can carry. This capacity can be increased if vehicles cross the intersections in platoons rather than one by one as they do today. Platoon formation is enabled by connected vehicle technology. This paper assesses the potential mobility benefits of platooning. It argues that saturation flow rates, and hence intersection capacity, can be doubled or tripled by platooning. The argument is supported by the analysis of three queuing models and by the simulation of a road network with 16 intersections and 73 links. The queuing analysis and the simulations reveal that a signalized network with fixed time control will support an increase in demand by a factor of (say) two or three if all saturation flows are increased by the same factor, with no change in the control. Furthermore, despite the increased demand vehicles will experience the same delay and travel time. The same scaling improvement is achieved when the fixed time control is replaced by the max pressure adaptive control. Part of the capacity increase can alternatively be used to reduce queue lengths and the associated queuing delay by decreasing the cycle time. Impediments to the control of connected vehicles to achieve platooning at intersections appear to be small.     

Modeling Capacity Reliability of Minor Roads at At-Grade Un-Signalized Intersections for Potential Performance Evaluation

Abstract

Given stochastic features of the demands on both the major road and the minor road at an at-grade un-signalized intersection, the capacity of the minor road is viewed as the vulnerable and critical part impacting on the overall capacity of the intersection. To facilitate the analysis of intersection performance reliability, the capacity reliability of the minor road is defined as the probability that the capacity of the minor road can accommodate a certain traffic demand at a certain degree of saturation. The headway distribution of traffic stream on major road is reflected by three types of distributions, namely, exponential distribution, shifted exponential distribution, and Cowan's M3 distribution. Based on field observations, the volumes on both major roads and minor roads are treated as correlated normal random variables. This paper presents the methods for modeling capacity reliability of the minor road at an at-grade un-signalized priority intersection. A method based on first-order reliability method is used to model the capacity reliability index. As important associated factors of capacity reliability analysis, the methods for modeling and analyzing capacity sensitivity of the minor road and reserve capacity of the priority intersection are also presented. A procedure for evaluating the intersection potential performance using capacity reliability, sensitivity and reserve capacity is developed and demonstrated with a numerical example. Finally, some new findings from the case studies are summarized.     

Network-wide adaptive tolling for connected and automated vehicles

This article proposes Δ-tolling, a simple adaptive pricing scheme which only requires travel time observations and two tuning parameters. These tolls are applied throughout a road network, and can be updated as frequently as travel time observations are made. Notably, Δ-tolling does not require any details of the traffic flow or travel demand models other than travel time observations, rendering it easy to apply in real-time. The flexibility of this tolling scheme is demonstrated in three specific traffic modeling contexts with varying traffic flow and user behavior assumptions: a day-to-day pricing model using static network equilibrium with link delay functions; a within-day adaptive pricing model using the cell transmission model and dynamic routing of vehicles; and a microsimulation of reservation-based intersection control for connected and autonomous vehicles with myopic routing. In all cases, Δ-tolling produces significant benefits over the no-toll case, measured in terms of average travel time and social welfare, while only requiring two parameters to be tuned. Some optimality results are also given for the special case of the static network equilibrium model with BPR-style delay functions.     

How to best address aviation’s full climate impact from an economic policy point of view? – Main results from AviClim research project

The interdisciplinary research project AviClim (Including Aviation in International Protocols for Climate Protection) has explored the feasibility for including aviation’s full climate impact, i.e., both long-lived CO₂ and short-lived non-CO₂ effects, in international protocols for climate protection and has investigated the economic impacts. Short-lived non-CO₂ effects of aviation are NO_x emissions, H₂O emissions or contrail cirrus, for instance.Four geopolitical scenarios have been designed which differ concerning the level of international support for climate protecting measures. These scenarios have been combined alternatively with an emissions trading scheme on CO₂ and non-CO₂ species, a climate tax and a NO_x emission charge combined with CO₂ trading and operational measures (such as lower flight altitudes). Modelling results indicate that a global emissions trading scheme for both CO₂ and non-CO₂ emissions would be the best solution from an economic and environmental point of view. Costs and impacts on competition could be kept at a relatively moderate level and effects on employment are moderate, too. At the same time, environmental benefits are noticeable.     

A multiclass cell transmission model for shared human and autonomous vehicle roads

Autonomous vehicles have the potential to improve link and intersection traffic behavior. Computer reaction times may admit reduced following headways and increase capacity and backwards wave speed. The degree of these improvements will depend on the proportion of autonomous vehicles in the network. To model arbitrary shared road scenarios, we develop a multiclass cell transmission model that admits variations in capacity and backwards wave speed in response to class proportions within each cell. The multiclass cell transmission model is shown to be consistent with the hydrodynamic theory. This paper then develops a car following model incorporating driver reaction time to predict capacity and backwards wave speed for multiclass scenarios. For intersection modeling, we adapt the legacy early method for intelligent traffic management (Bento et al., 2013) to general simulation-based dynamic traffic assignment models. Empirical results on a city network show that intersection controls are a major bottleneck in the model, and that the legacy early method improves over traffic signals when the autonomous vehicle proportion is sufficiently high.     

Assessing carbon emissions from road transport through traffic flow estimators

Carbon emissions from road transport are one of the main issues related to modern transport planning. To address them adequately, the acquisition of reliable data about traffic flow is an essential prerequisite. However, the large quantity and the heterogeneity of available information often cause problems; missing or incomplete data are one of the most critical aspects. This paper discusses how technology handles imperfect information in order to obtain more accurate quantification of CO₂ emissions. First, an analysis of single estimators and combination models is provided, highlighting their main characteristics. Then, the TANINO model (Tool for the Analysis of Non-conservative Carbon Emissions In TraNspOrt) is presented, jointly developed at the University of Seville and at the IUAV University of Venice. It consists of two different modules: the first is a combination model that optimizes the results of three traffic flow single estimators, while the second is a macro-model of carbon evaluation, which takes into account road infrastructure, vehicle type and traffic conditions. TANINO is then tested to calculate CO₂ emissions along the ring road of the Spanish city of Seville, showing its more efficient performance, compared to the single estimators normally adopted for such aims. Transport planning can benefit from the adequate knowledge of traffic flows and related CO₂ emissions, since it allows a more reliable monitoring of the progresses granted by specific carbon policies.     

Characterising Green Light Optimal Speed Advisory trajectories for platoon-based optimisation

Conceptually, a Green Light Optimal Speed Advisory (GLOSA) system suggests speeds to vehicles, allowing them to pass through an intersection during the green interval. In previous papers, a single speed is computed for each vehicle in a range between acceptable minimum and maximum values (for example between standstill and the speed limit). This speed is assumed to be constant until the beginning of the green interval, and sent as advice to the vehicle. The goal is to optimise for a particular objective, whether it be minimisation of emissions (for environmental reasons), fuel usage or delay. This paper generalises the advice given to a vehicle, by optimising for delay over the entire trajectory instead of suggesting an individual speed, regardless of initial conditions – time until green, distance to intersection and initial speed. This may require multiple acceleration manoeuvres, so the advice is sent as a suggested acceleration at each time step. Such advice also takes into account a suitable safety constraint, ensuring that vehicles are always able to stop before the intersection during a red interval, thus safeguarding against last-minute signal control schedule changes. While the algorithms developed primarily minimise delay, they also help to reduce fuel usage and emissions by conserving kinetic energy. Since vehicles travel in platoons, the effectiveness of a GLOSA system is heavily reliant on correctly identifying the leading vehicle that is the first to be given trajectory advice for each cycle. Vehicles naturally form a platoon behind this leading vehicle. A time loop technique is proposed which allows accurate identification of the leader even when there are complex interactions between preceding vehicles. The developed algorithms are ideal for connected autonomous vehicle environments, because computer control allows vehicles’ trajectories to be managed with greater accuracy and ease. However, the advice algorithms can also be used in conjunction with manual control provided Vehicle-to-Infrastructure (V2I) communication is available.     

A linear programming formulation for autonomous intersection control within a dynamic traffic assignment and connected vehicle environment

This paper develops a novel linear programming formulation for autonomous intersection control (LPAIC) accounting for traffic dynamics within a connected vehicle environment. Firstly, a lane based bi-level optimization model is introduced to propagate traffic flows in the network, accounting for dynamic departure time, dynamic route choice, and autonomous intersection control in the context of system optimum network model. Then the bi-level optimization model is transformed to the linear programming formulation by relaxing the nonlinear constraints with a set of linear inequalities. One special feature of the LPAIC formulation is that the entries of the constraint matrix has only {−1, 0, 1} values. Moreover, it is proved that the constraint matrix is totally unimodular, the optimal solution exists and contains only integer values. It is also shown that the traffic flows from different lanes pass through the conflict points of the intersection safely and there are no holding flows in the solution. Three numerical case studies are conducted to demonstrate the properties and effectiveness of the LPAIC formulation to solve autonomous intersection control.     

The symmetric intersection design and traffic control optimization

It is well recognized that the left-turning movement reduces the intersection capacity significantly, because exclusive left turn phases are needed to discharge left turn vehicles only. This paper proposes the concept of Left-Hand Traffic (LHT) arterial, on where vehicles follow left-hand traffic rules as in England and India. The unconventional intersection where a LHT arterial intersects with a Right-Hand Traffic (RHT) arterial is named as symmetric intersection. It is only need three basic signal phases to separate all conflicts at symmetric intersection, while it at least need four signal phases at a conventional intersection. So, compared with the conventional intersection, the symmetric intersection can provide longer green time for the left-turning and the through movement, which can increase the capacity significantly. Through-movement waiting areas (TWAs) can be set at the symmetric intersection effectively, which can increase the capacity and short the cycle length furthermore. And the symmetric intersection is Channelized to improve the safety of TWAs. The Binary-Mixed-Integer-Linear-Programming (BMILP) model is employed to formulate the capacity maximization problem and signal cycle length minimization problem of the symmetric intersection. The BMILP model can be solved by standard branch-and-bound algorithms efficiently and outputs the lane allocation, signal timing decisions, and other decisions. Experiments analysis shows that the symmetric intersection with TWAs can increase the capacity and short the signal cycle length.     

Isolated intersection control for various levels of vehicle technology: Conventional,connected, and automated vehicles

Connected vehicle technology can be beneficial for traffic operations at intersections. The information provided by cars equipped with this technology can be used to design a more efficient signal control strategy. Moreover, it can be possible to control the trajectory of automated vehicles with a centralized controller. This paper builds on a previous signal control algorithm developed for connected vehicles in a simple, single intersection. It improves the previous work by (1) integrating three different stages of technology development; (2) developing a heuristics to switch the signal controls depending on the stage of technology; (3) increasing the computational efficiency with a branch and bound solution method; (4) incorporating trajectory design for automated vehicles; (5) using a Kalman filter to reduce the impact of measurement errors on the final solution. Three categories of vehicles are considered in this paper to represent different stages of this technology: conventional vehicles, connected but non-automated vehicles (connected vehicles), and automated vehicles. The proposed algorithm finds the optimal departure sequence to minimize the total delay based on position information. Within each departure sequence, the algorithm finds the optimal trajectory of automated vehicles that reduces total delay. The optimal departure sequence and trajectories are obtained by a branch and bound method, which shows the potential of generalizing this algorithm to a complex intersection.Simulations are conducted for different total flows, demand ratios and penetration rates of each technology stage (i.e. proportion of each category of vehicles). This algorithm is compared to an actuated signal control algorithm to evaluate its performance. The simulation results show an evident decrease in the total number of stops and delay when using the connected vehicle algorithm for the tested scenarios with information level of as low as 50%. Robustness of this algorithm to different input parameters and measurement noises are also evaluated. Results show that the algorithm is more sensitive to the arrival pattern in high flow scenarios. Results also show that the algorithm works well with the measurement noises. Finally, the results are used to develop a heuristic to switch between the different control algorithms, according to the total demand and penetration rate of each technology.     

The influence of e-carsharing schemes on electric vehicle adoption and carbon emissions: An emerging economy study

Moving toward sustainable mobility, the sharing economy business model emerges as a prominent practice that can contribute to the transition to sustainability. Using a system dynamics modeling approach, this paper investigates the impacts of an e-carsharing scheme in carbon emissions and in electric vehicle adoption. We study the VAMO scheme located in Fortaleza, Brazil, as the first e-carsharing scheme in the country. We study two policies combined: a VAMO planned growth policy and a retirement policy for conventional vehicles. Our results show that the VAMO incentive policy is an important factor to reduce emissions and to increase awareness of electric vehicles, highlighting the role of the government as an institutional entrepreneur, stimulating and sustaining the VAMO scheme. The retirement policy in combination with the VAMO incentive policy obtained the best results in our simulations, reducing 29% of CO₂ emissions and increasing 36% electric vehicle adoption, when compared to the business-as-usual scenario. The main conclusions are that such e-carsharing schemes offer direct and indirect benefits to urban mobility (specially to electric vehicle adoption) and that they depend on how the government supports them.     

Paradoxes of reservation-based intersection controls in traffic networks

Reservation-based intersection control is a revolutionary idea for using connected autonomous vehicle technologies to improve intersection controls. Vehicles individually request permission to follow precise paths through the intersection at specific times from an intersection manager agent. Previous studies have shown that reservations can reduce delays beyond optimized signals in many demand scenarios. The purpose of this paper is to demonstrate that signals can outperform reservations through theoretical and realistic examples. We present two examples that exploit the reservation protocol to prioritize vehicles on local roads over vehicles on arterials, increasing the total vehicle delay. A third theoretical example demonstrates that reservations can encourage selfish route choice leading to arbitrarily large queues. Next, we present two realistic networks taken from metropolitan planning organization data in which reservations perform worse than signals. We conclude with significantly positive results from comparing reservations and signals on the downtown Austin grid network using dynamic traffic assignment. Overall, these results indicate that network-based analyses are needed to detect adverse route choices before traffic signals can be replaced with reservation controls. In asymmetric intersections (e.g. local road-arterial intersections), reservation controls can cause several potential issues. However, in networks with more symmetric intersections such as a downtown grid, reservations have great potential to improve traffic.     

Mitigating negative impacts of near-side bus stops on cars

Bus stops are often placed short distances upstream of signalized intersections. Buses that dwell at one of these so-called near-side stops can impede queued cars upstream from discharging through the intersection during green times. Residual car queues can form at the intersection as a result. The smaller the distance between a stop and its intersection, the greater the problem can be.Models are formulated to address this problem using kinematic wave theory. The models can be used to determine where to place a near-side stop to achieve a target level of residual car queueing. In addition, the models are used herein to develop a scheme for mitigating residual car queues by briefly detaining some buses from reaching the stop. The scheme can be applied selectively, so that the times that detained buses depart from the stop are not postponed. The buses are therefore not delayed over the longer run. Analysis indicates that this bus-holding scheme can significantly reduce car delays and queueing. Our models for placing stops and holding buses are shown to be robust to systematic and random changes in car flow.     

Simultaneous control of traffic lights and bus departure for priority operation

This article presents a bus priority method for traffic light control based on two modes of operation: immediate and controlled departure. The immediate departure mode is a standard procedure in which the intersection controller grants priority upon request of the bus. Controlled departure acts to avoid a second stop of the bus at the end of the queue formed during red by holding the bus at the bus stop, while still granting priority to the bus lane. Selection of one of the two modes is based on intersection cost that includes bus delay and the impact on the overall traffic near the intersection. The method is applied in a constant cycle scenario where green recall and green extension can only be granted within certain limits. Numerical examples illustrate the application of the approach.     

Development of a delay model for unsignalized intersections applicable to traffic assignment

Abstract

This paper develops a model for estimating unsignalized intersection delays which can be applied to traffic assignment (TA) models. Current unsignalized intersection delay models have been developed mostly for operational purposes, and demand detailed geometric data and complicated procedures to estimate delay. These difficulties result in unsignalized intersection delays being ignored or assumed as a constant in TA models.

Video and vehicle license plate number recognition methods are used to collect traffic volume data and to measure delays during peak and off-peak traffic periods at four unsignalized intersections in the city of Tehran, Iran. Data on geometric design elements are measured through field surveys. An empirical approach is used to develop a delay model as a function of influencing factors based on 5- and 15-min time intervals. The proposed model estimates delays on each approach based on total traffic volumes, rights-of-way of the subject approach and the intersection friction factor. The effect of conflicting traffic flows is considered implicitly by using the intersection friction factor. As a result, the developed delay model guarantees the convergence of TA solution methods.

A comparison between delay models performed using different time intervals shows that the coefficients of determination, R ², increases from 43.2% to 63.1% as the time interval increases from 5- to 15-min. The US Highway Capacity Manual (HCM) delay model (which is widely used in Iran) is validated using the field data and it is found that it overestimates delay, especially in the high delay ranges.     

Self-organizing traffic signals using secondary extension and dynamic coordination

Actuated traffic signal control logic has many advantages because of its responsiveness to traffic demands, short cycles, effective use of capacity leading to and recovering from oversaturation, and amenability to aggressive transit priority. Its main drawback has been its inability to provide good progression along arterials. However, the traditional way of providing progression along arterials, coordinated–actuated control with a common, fixed cycle length, has many drawbacks stemming from its long cycle lengths, inflexibility in recovering from priority interruptions, and ineffective use of capacity during periods of oversaturation. This research explores a new paradigm for traffic signal control, “self-organizing signals,” based on local actuated control but with some additional rules that create coordination mechanisms. The primary new rules proposed are for secondary extensions, in which the green may be held to serve an imminently arriving platoon, and dynamic coordination, in which small groups of closely spaced signals communicate with one another to cycle synchronously with the group’s critical intersection. Simulation tests in VISSIM performed on arterial corridors in Massachusetts and Arizona show overall delay reductions of up to 14% compared to an optimized coordinated–actuated scheme where there is no transit priority, and more than 30% in scenarios with temporary oversaturation. Tests also show that with self-organizing control, transit signal priority can be more effective than with coordinated–actuated control, reducing transit delay by about 60%, or 12 to 14 s per intersection with little impact on traffic delay.     

Efficient intersection control for minimally guided vehicles: A self-organised and decentralised approach

An important question for the practical applicability of the highly efficient traffic intersection control is about the minimal level of intelligence the vehicles need to have so as to move beyond the traffic light control. We propose an efficient intersection traffic control scheme without the traffic lights, that only requires a majority of vehicles on the road to be equipped with a simple driver assistance system. The algorithm of our scheme is completely decentralised, and takes into full account the non-linear interaction between the vehicles at high density. For vehicles approaching the intersection in different directions, our algorithm imposes simple interactions between vehicles around the intersection, by defining specific conditions on the real-time basis, for which the involved vehicles are required to briefly adjust their dynamics. This leads to a self-organised traffic flow that is safe, robust, and efficient. We also take into account of the driver comfort level and study its effect on the control efficiency. The scheme has low technological barrier, minimal impact on the conventional driving behaviour, and can coexist with the traffic light control. It also has the advantages of being easily scalable, and fully compatible with both the conventional road systems as well as the futuristic scenario in which driverless vehicles dominate the road. The mathematical formulation of our scheme permits large scale realistic numerical simulations of busy intersections, allowing a more complete evaluation of the control performance, instead of just the collision avoidance at the intersection.     

长途跨线高速列车直达与中转选择问题

我国快速客运网基本形成,长途跨线列车直达与中转选择对于高速列车开行方案设计至关重要。为提升长途跨线高速列车开行效益和服务品质,按长途跨线列车直达与中转方式对比的思路,以旅客出行需求、基础设施能力、移动设备能力等多方面因素对长途跨线列车开行方式的影响为约束条件,研究长途跨线列车直达与中转选择模型及求解方法。选取2025年15个长途跨线起讫点为对象进行案例研究,提出D站—E站、F站—D站等9个起迄点之间开行长途跨线直达列车的建议方案,研究表明直达与中转换乘选择模型能够解决长途跨线列车开行方案编制问题。     

Combining Intermodal Transport With Electric Vehicles: Towards More Sustainable Solutions

Abstract

This paper analyses the feasibility of incorporating electric or hybrid vehicles in intermodal transport for the transportation of containers in the pre- and post haulage (PPH) operation. In Europe, the intermodal transport market is being strongly supported, as it is seen as one of the keystones of a sustainable mobility system policy. The introduction of environmentally friendly electric/hybrid vehicles for the pre- and post haulage operation would mean a further enhancement leading to a more complete ecological intermodal transport chain. PPH operations are usually no longer than 30 km, and, hence, could possibly be handled by electric or hybrid vehicles.

Hybrid electric vehicles (HEV) combine electric and other drive systems, such as internal combustion engines, gas turbines and fuel cells. Hybrid electric vehicles merge the zero pollution and high efficiency benefits of electric traction with the high fuel energy density benefits of an energy source or thermal engine. The use of electrically driven vehicles for goods distribution has already been successfully proven in international demonstration projects, such as ELCIDIS. Transport of intermodal units (such as ISO containers), however, requires electric/hybrid heavy-duty goods vehicles, which are not readily available on the market, but for which the technology exists.

Different possibilities are assessed as to their technical, financial, organizational and environmental feasibility and suitability. This analysis is based on a typical mission for pre-and post haulage operations, such as type of trips, distance, frequency, urban/suburban, etc.