用于海洋结构的锌矩阵/TiO_2-WO_3纳米复合涂料微结构、机械和耐腐蚀的WO_3纳米粒子负载效应（英文）

In this study, for marine application purposes, we evaluated the effect of process parameter and particle loading on the microstructure, mechanical reinforcement and corrosion resistance properties of a Zn-TiO_2-WO_3 nanocomposite produced via electrodeposition. We characterized the morphological properties of the composite coatings with a Scanning Electron Microscope(SEM) equipped with an Energy Dispersive Spectrometer(EDS). We carried out mechanical examination using a Dura Scan hardness tester and a CERT UMT-2 multi-functional tribological tester. We evaluated the corrosion properties by linear polarization in 3.5% Na Cl. The results show that the coatings exhibited good stability and the quantitative particle loading greatly enhanced the structural and morphological properties, hardness behavior and corrosion resistance of the coatings. We observed the precipitation of this alloy on steel is greatly influenced by the composite characteristics.     

Effect of pH on mechanical,physical and tribological properties of electroless Ni-P-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite deposits for marine applications

Successful co-deposition of fine particulate matter within an Electroless Nickel-Phosphorous (ENi-P) matrix is dependent on various factors like bath composition, particle compatibility with metallic matrix, bath reactivity (pH), particle size and their distribution. ENi-P deposits incorporating Al₂O₃/Alumina in a disperse phase have varied effects on properties and attributes like surface roughness (Ra), microhardness, wear resistance, corrosion resistance and surface morphology of the deposits obtained. This paper experimentally investigates the effect of alumina (1.55 g/L) on Ra, microhardness, surface morphology, deposition rate, wettability, wear resistance and corrosion resistance of ENi-P-Al₂O₃ composite deposits on mild steel substrates at bath pH 5, 7 and 9. Study reveals that optimum deposit parameters and deposition rates are achieved with bath pH. However, not much study has been undertaken concerning composite deposits obtained from higher bath pH or basic bath. This is attributable to the fact that at higher bath pH or alkaline baths, the bath gets unstable and eventually degrades or decomposes, thereby resulting in sub optimal or poor deposition. Hence, experimental investigations carried out by preparing suitable baths, operating under optimum conditions, and enabling successful composite deposition in acidic and alkaline baths have revealed that there is a significant improvement in the above mentioned properties of the as-deposited composite deposits, as the pH is increased from pH 5 to pH 9. This aspect can therefore be advantageously utilized for preparing various marine components like fasteners, nuts, bolts, washers, pipes, cables, components having relative motion etc.     

舰船高温排烟管表面纳米Al2O3-CeO2/Ni镀层的微观组织和抗高温氧化性能

为了制备具有优异抗氧化性能的复合镀层,试验采用双脉冲电源,在舰船高温排烟管试样表面沉积Al2O3-CeO2/Ni纳米复合镀层,通过抗氧化性能测试,研究了Al2O3纳米颗粒浓度和CeO2浓度对复合镀层的抗氧化性的影响。试验得出复合镀层的微观组织随着Al2O3颗粒的添加细化晶粒,当镀液中纳米CeO2颗粒浓度增加到1.5 g/L时,晶粒尺寸分布均匀,同时镀层表面平整、致密;复合镀层的抗氧化性随镀液中纳米Al2O3浓度增加而增加,随CeO2浓度的增加先降低后增加。     

Application of H∞ filtering in the initial alignment of strapdown inertial navigation system

In this paper , the principle of H∞ filtering is discussed and H∞ filter is constructed, which is used in the initial alignment of the strapdown inertial navigation systems(SINS). The error model of SINS is derived. By utilizing constructed H∞ filter, the filtering calculation to that system has been conducted. The simulation results of the misalignment angle are given under the condition of unknown noises. The results show that the process of alignment with H∞ filter is much faster and with excellent robustness.     

KG<Subscript>max</Subscript> curves associated with second generation intact stability criteria for different types of ships

Currently, second generation intact stability criteria are being developed and evaluated by the International Maritime Organization (IMO). In this paper, we briefly present levels 1 and 2 assessment methods for the criteria of pure loss of stability and parametric roll failure modes. Subsequently, we show the KG_max curves associated with these criteria. We compute these curves for five different types of ships and compare them with the curves embodied in the current regulations. The results show that the safety margin ensured by the first level-1 method of calculation for both pure loss of stability and parametric roll seems to be excessive in many cases. They also show that the KG_max given by the second level-1 method and by the level-2 method may be very similar. In some cases, the level-2 method can be more conservative than the second level-1 method, which is unanticipated by the future regulation. The KG_max curves associated with parametric roll confirm that the C11 container ship is vulnerable to this failure mode. The computation of the second check coefficient of parametric roll level 2 (C2) for all possible values of KG reveals the existence of both authorized and restricted areas on the surface formed by both the draft and KG, which may replace the classical KG_max curves. In consequence, it is not sufficient to check that C2 is lower than the maximum authorized value (R _PR0) for a fixed ship’s loading condition.     

海洋工程用铝合金表面微弧氧化膜的耐腐蚀性能

为了制备性能良好的微弧氧化膜层,以提高海洋平台用2Al2铝合金的耐磨性和耐腐蚀性。本实验采用微弧氧化技术,将不同浓度的MoS2颗粒（0 g/L、1 g/L、2 g/L、4 g/L、6 g/L和8 g/L）添加到电解液中,在2Al2铝合金表面制备微弧氧化膜层。通过扫描电子显微镜和光学显微镜对复合镀层的微观形貌、组织结构进行分析;采用摩擦磨损试验、电化学腐蚀试验等实验方法分析了镀层的耐磨性和耐腐蚀性能。实验结果表明,随着纳米MoS2颗粒含量的增加,陶瓷层表面微孔尺寸减小,微孔数量增加,并且孔洞的分布更加均匀,致密度得到了很大的提高,且膜层厚度随着纳米MoS2颗粒含量的增加先增后减;添加纳米MoS2颗粒后,使得膜层摩擦系数降低,并且基本稳定在0.45左右;当纳米MoS2颗粒含量为4g/L时,陶瓷层的耐腐蚀性能最好。     

NaOH含量对AZ91D镁合金微弧氧化膜层微观结构和耐蚀性的影响

在由15 g/L Na2SiO3、12 g/L NaAlO2、3 g/L Na2B4O7、5 mL/L C3H8O3、5 g/L C6H5Na3O7及1~4 g/L NaOH组成的硅铝复合电解液中,利用微弧氧化技术在AZ91D镁合金基体上制备了一系列陶瓷膜层.利用扫描电镜、膜层测厚仪分别研究了陶瓷膜层的微观结构及厚度;采用全浸泡实验和交流阻抗实验测试了膜层在3.5%NaCl溶液中的耐蚀性能.结果表明：随着NaOH含量的增加,微弧氧化过程中的起弧电压和终止电压均呈线性下降;膜层的耐蚀性随着NaOH含量的增加先提高后降低,膜厚的变化趋势与其耐蚀性的变化趋势基本一致;NaOH含量的变化主要影响膜层内部致密层的耐蚀性能;当NaOH含量为2 g/L时,膜层最厚,膜层较致密,因而具有较好的耐蚀性能.     

Q235钢等离子喷涂Cr2O3涂层性能研究

采用PT3X IPS-1000等离子喷涂系统在Q235钢表面制备Cr_2O_3涂层,利用金相显微镜、扫描电镜(SEM)、能谱仪(EDS)和硬度计等设备观察涂层微观形貌、测试元素组成及硬度等表面性能,采用电化学测试、盐雾试验等手段研究涂层耐腐蚀性能。结果表明:等离子喷涂Cr_2O_3涂层表面均匀,硬度比基材提高约600 HV,自腐蚀电位增加0.509 V,耐腐蚀性能显著增加,对基材形成良好保护。     

纳米Al2O3复合镀铁层的结构与性能

为提高船机零部件的耐磨性,减少零部件的磨损,通过在电镀液中添加Al2O3纳米颗粒的方法,制备出含有Al2O3纳米颗粒的复合镀铁层。对制备出的镀层进行硬度、表面形貌、元素成分和摩擦磨损性能分析。结果表明：Al2O3纳米颗粒成功进入了镀层,含有Al2O3颗粒的复合镀层相对普通镀铁层有明显提高；含有40g/L Al2O3的复合镀层的摩擦系数相对普通镀层下降了25%,磨损量也大幅下降；经过摩擦磨损后复合镀层的表面状态良好。     

The influence of route choice and operating conditions on fuel consumption and CO<Subscript>2</Subscript> emission of ships

The influence of various parameters, such as ship initial speed (full ahead and lower engine loads), loading condition, heading angle and weather conditions on ship fuel consumption and CO₂ emission is presented. A reliable methodology for estimating the attainable ship speed, fuel consumption and CO₂ emission in different sea states is described. The speed loss is calculated by taking into account the engine and propeller performance in actual seas as well as the mass inertia of the ship. The attainable ship speed is obtained as time series. Correlation of speed loss with sea states allows predictions of propulsive performance in actual seas. If the computation is used for weather routing purposes, values for various ship initial speed, loading conditions and heading angles for each realistic sea‐state must be provided. The voluntary speed loss is taken into account. The influence of the ship speed loss on various parameters such as fuel consumption and CO₂ emissions is presented. To illustrate the presented concept, the ship speed and CO₂ emissions in various routes of the Atlantic Ocean are calculated using representative environmental design data for the track of the routes where the ship will sail.     

纳米MoS2颗粒对海洋平台铝合金钻探管表面微弧氧化膜的性能影响

为了使海洋平台铝合金钻探管具有优异的耐腐蚀性能,试验采用微弧氧化技术,在海洋平台钻探管用2A12铝合金表面制备氧化铝陶瓷膜。本试验研究了纳米颗粒添加量对微弧氧化膜的微观形貌、组织结构和耐腐蚀性的影响。试验得出：MoS₂纳米颗粒添加量对微弧氧化膜的制备影响较大,随着MoS₂纳米颗粒添加量的增加,微弧氧化膜的厚度有增大的趋势,孔径先增大后减小,膜表面越来越致密光滑;随着MoS₂纳米颗粒添加量的增加,微弧氧化膜的耐腐蚀性能提高,当MoS₂纳米颗粒添加量由0.5g/L增加到2g/L时,腐蚀速率由0.00032g.(dm₂)_-1.h_-1降低至0.00024g.(dm₂)_-1.h_-1。     

pH值对用于海洋环境的Ni-P-Al_2O_3化学复合镀层的机械,物理和摩擦学属性影响效应（英文）

Successful co-deposition of fine particulate matter within an Electroless Nickel-Phosphorous(ENi-P) matrix is dependent on various factors like bath composition, particle compatibility with metallic matrix, bath reactivity(pH), particle size and their distribution. ENi-P deposits incorporating Al_2O_3/Alumina in a disperse phase have varied effects on properties and attributes like surface roughness(Ra), microhardness, wear resistance, corrosion resistance and surface morphology of the deposits obtained. This paper experimentally investigates the effect of alumina(1.55 g/L) on Ra, microhardness, surface morphology, deposition rate, wettability, wear resistance and corrosion resistance of ENi-P-Al_2O_3 composite deposits on mild steel substrates at bath pH 5, 7 and 9. Study reveals that optimum deposit parameters and deposition rates are achieved with bath pH. However, not much study has been undertaken concerning composite deposits obtained from higher bath pH or basic bath. This is attributable to the fact that at higher bath pH or alkaline baths, the bath gets unstable and eventually degrades or decomposes, thereby resulting in sub optimal or poor deposition. Hence, experimental investigations carried out by preparing suitable baths, operating under optimum conditions, and enabling successful composite deposition in acidic and alkaline baths have revealed that there is a significant improvement in the above mentioned properties of the as-deposited composite deposits, as the pH is increased from pH 5 to pH 9. This aspect can therefore be advantageously utilized for preparing various marine components like fasteners, nuts, bolts, washers, pipes, cables, components having relative motion etc.     

颜料及包覆颜料对光固化涂料耐蚀性能的影响

研究了光固化涂料中颜料和经过包覆改性后的颜料对涂层耐蚀性能的影响。交流阻抗实验测试结果表明颜料对涂层的耐蚀性有很好地增强作用,并结合扫描电镜分析了颜料对涂层耐蚀性提高的原因。此外,利用硬脂酸和硬脂酸盐对群青表面进行改性,结果表明硬脂酸包覆过的颜料涂层阻抗值最大,涂层耐腐蚀性能最好,并就包覆颜料对涂层的耐蚀机理进行了探讨。     

基于转盘测阻法的天然乳胶涂层减阻特性研究

利用转盘测阻法对天然乳胶涂层的减阻特性进行探究,确定雷诺数和柔性系数对涂层减阻效果的影响。利用喷涂法将天然乳胶和氨水混合溶液喷涂于转盘上,制成一种柔性涂层,并通过密度测定、硬度测定、力学性能测试和动态热力学分析等试验方法对涂层的物理性能与基本力学性能进行测定。试验结果显示,天然乳胶涂层密度为950 kg/m³,与水的密度接近,并且该涂层具有弹性模量低、撕裂强度大,断裂伸长率大的优点。采用转盘测阻法对涂层阻力进行测试,结果显示,当涂层厚度为0.2 mm、转速为100 r/min时达到最大减阻率15%,因此可断定天然乳胶涂层具有良好的物理机械性能,其减阻效果与水流状态及自身柔性存在一定关系,在特定情况下可实现良好的减阻效果。     

2205双相不锈钢焊接工艺及耐腐蚀性能分析

采用不同焊接工艺对2205双相不锈钢进行焊接,分析不同焊接工艺对焊接接头力学性能、微观组织及耐腐蚀性能的影响。结果显示:在晶粒无明显长大时,焊缝及热影响区冲击韧性随奥氏体质量分数的增加而升高;采用熔化极气体保护焊(Gas Metal Arc Welding,GMAW)时,保护气体中加入N2可有效提高焊接接头各区域奥氏体质量分数,从而提高焊接接头力学性能及耐腐蚀性能;2205双相不锈钢母材及焊缝腐蚀速率均明显随腐蚀液质量分数的升高而增加。优化双相不锈钢焊接工艺参数,保证其焊接接头具有良好的综合性能,对于该类材料构件及产品的制造、推广及使用意义重大。     

工艺参数对原油船用耐蚀钢DWSAW焊接接头的影响

论述前后丝模式、焊接电流、焊接电压和焊接速度对国产原油船用耐蚀钢双丝埋弧焊（Double Wire Submerged Arc Welding，DWSAW）焊缝成型的影响，开展耐蚀钢DWSAW工艺试验，分析耐蚀钢DWSAW焊接接头的力学性能和耐腐蚀性能。结果表明，国产原油船用耐蚀钢具有良好的DWSAW适应性，采用合适的焊接工艺可获得力学性能和耐腐蚀性能兼顾的焊接接头。     

n-Al2O3/Fe/SiC复合镀技术修复船舶空压机曲轴方法研究

针对目前船舶空压机曲轴等机械部件修复中存在的问题,对研制出的基于n-Al2O3/Fe/SiC纳米材料复合镀技术的修复工艺进行研究。介绍了新型纳米复合镀的应用范围、共沉积机理,对磨损的船舶空压机曲轴进行了修复试验,并对修复后的镀层进行了结合强度、耐磨性、硬度等物理机械性能试验,得出了试验结论。最后得出该纳米复合镀修复工艺能够应用于受损的机械部件。     

Analysis of corrosion risk due to chloride diffusion for concrete structures in marine environment

The chloride-induced steel corrosion is one of the main causes of deterioration for reinforced concrete structures exposed to marine environments. The chloride ingress into reinforced concrete structures is even more complex since it depends on random parameters linked to transport and chemical properties of materials, which results in variability of corrosion initiation. This variation raises the need of statistical approaches to evaluate the risk of corrosion initiation due to chloride ingress. To address this issue, we use sensitivity analysis to identify the influence of input parameters on critical length of time before corrosion initiation predicted by our chloride diffusion model. Exceedance probabilities of corrosion initiation time given that input parameters exceed certain thresholds were also calculated. Results showed that the corrosion initiation time was most sensitive to: chloride effective diffusion coefficient D_e in concrete, that is a parameter controllable by relevant stakeholders; surface chloride concentration C_s, a non-controllable parameter depending on surrounding conditions. Reducing the chloride diffusion coefficient enables us to postpone the maintenance of structures. However, the interaction between controllable parameters and non-controllable surrounding conditions was revealed influential on the reliability of results. For instance, the probability that corrosion initiation time exceeds 15 years given an effective diffusion coefficient (D_e) equal to 0.1 × 10⁻¹² m²⋅s-1 can vary from 19 to 41% according to stochastic variations of chloride concentrations (C_s) values. Postponing the corrosion initiation time was combined with a decreasing probability of its occurrence.     

舰船高温排烟管表面复合镀层氧化性能的研究

为了制备具有优异抗氧化性能的复合镀层,试验采用双脉冲电源,在舰船高温排烟管试样表面沉积Ni-Al2O3纳米复合镀层,采用抗氧化性能测试,研究工艺参数对复合镀层的抗氧化性的影响。试验得出复合镀层的抗氧化性随镀液中纳米 Al2O3浓度增加而增加,凹凸棒土的添加可以提高抗氧化性,随 CeO2浓度的增加先降低后增加,随占空比的增加先增加后降低。     

半潜平台结构件表面复合镀层耐腐蚀性的研究

为了制备具有优异耐腐蚀性能的复合镀层,试验采用双脉冲电源,在Q235半潜平台结构件表面沉积Ni-Si C纳米复合镀层,采用浸泡腐蚀试验,研究了工艺参数对复合镀层的耐腐蚀性的影响。试验得出复合镀层的腐蚀失重随镀液中纳米Si C颗粒浓度的增加而增加,随电流密度的增加而增加,且采用双脉冲镀的复合镀层耐腐蚀性能更好。