The Intermittent Bus Lane signals setting within an area

Intermittent Bus Lane (IBL) used for bus priority is a lane in which the status of a given section changes according to the presence or not of a bus in its spatial domain: when a bus is approaching such a section, the status of that lane is changed to BUS lane, and after the bus moves out of the section, it becomes a normal lane again, open to general traffic. Therefore when bus services are not so frequent, general traffic will not suffer much, and bus priority can still be obtained. This measure can be operating at a single city block, but if all related control parameters along bus lines are considered together, more time gains can be obtained. In this paper, the basic structure and operation of IBL around a single intersection are briefly introduced, then the construction of an objective function and its relationships with the related priority control parameters along one bus line and their simplifications are described. Finally the calculations of the priority control parameters when there are several connected bus lines within an area and some simulation results are discussed.     

Bus Priority Using pre-signals

The need to provide efficient public transport services in urban areas has led to the implementation of bus priority measures in many congested cities. Much interest has recently centred on priority at signal controlled junctions, including the concept of pre-signals, where traffic signals are installed at or near the end of a with-flow bus lane to provide buses with priority access to the downstream junction. Although a number of pre-signals have now been installed in the U.K., particularly in London, there has been very little published research into their design, operation and optimisation. This paper addresses these points through the development of analytical procedures which allow pre-implementation evaluation of specific categories of pre-signals. The paper initially sets out three categories of pre-signal, which have different operating characteristics, different requirements for signalling and different impacts on capacity and delay. Key issues concerning signalling arrangements for these categories are then discussed, together with a summary of the analytical approach adopted and the assumptions required. Equations are developed to allow appropriate signal timings to be calculated for pre-signalised intersections. Further equations are then developed to enable delays to priority and non-priority traffic, with and without pre-signals, to be estimated with delay being taken here as the key performance criterion. The paper concludes with three application examples illustrating how the equations are applied and the impacts of pre-signals in different situations.The analyses confirm the potential benefits of pre-signals, where these signals apply to non-priority traffic only. Where buses are also subject to a pre-signal, it is shown that disbenefits to buses can often occur, unless bus detectors are used to gain priority signalling.     

Simultaneous control of traffic lights and bus departure for priority operation

This article presents a bus priority method for traffic light control based on two modes of operation: immediate and controlled departure. The immediate departure mode is a standard procedure in which the intersection controller grants priority upon request of the bus. Controlled departure acts to avoid a second stop of the bus at the end of the queue formed during red by holding the bus at the bus stop, while still granting priority to the bus lane. Selection of one of the two modes is based on intersection cost that includes bus delay and the impact on the overall traffic near the intersection. The method is applied in a constant cycle scenario where green recall and green extension can only be granted within certain limits. Numerical examples illustrate the application of the approach.     

Integrated optimization of bus priority operations in connected vehicle environment

Most previous works associated with transit signal priority merely focus on the optimization of signal timings, ignoring both bus speed and dwell time at bus stops. This paper presents a novel approach to optimize the holding time at bus stops, signal timings, and bus speed to provide priority to buses at isolated intersections. The objective of the proposed model is to minimize the weighted average vehicle delays of the intersection, which includes both bus delay and impact on nearby intersection traffic, ensuring that buses clear these intersections without being stopped by a red light. A set of formulations are developed to explicitly capture the interaction between bus speed, bus holding time, and transit priority signal timings. Experimental analysis is used to show that the proposed model has minimal negative impacts on general traffic and outperforms the no priority, signal priority only, and signal priority with holding control strategies (no bus speed adjustment) in terms of reducing average bus delays and stops. A sensitivity analysis further demonstrates the potential of the proposed approach to be applied to bus priority control systems in real‐time under different traffic demands, bus stop locations, and maximum speed limits. Copyright © 2016 John Wiley & Sons, Ltd.     

Integrated optimization of transit priority operation at isolated intersections: A person-capacity-based approach

In this paper, a person-capacity-based optimization method for the integrated design of lane markings, exclusive bus lanes, and passive bus priority signal settings for isolated intersections is developed. Two traffic modes, passenger cars and buses, have been considered in a unified framework. Person capacity maximization has been used as an objective for the integrated optimization method. This problem has been formulated as a Binary Mixed Integer Linear Program (BMILP) that can be solved by a standard branch-and-bound routine. Variables including, allocation of lanes for different passenger car movements (e.g., left turn lanes or right turn lanes), exclusive bus lanes, and passive bus priority signal timings can be optimized simultaneously by the proposed model. A set of constraints have been set up to ensure feasibility and safety of the resulting optimal lane markings and signal settings. Numerical examples and simulation results have been provided to demonstrate the effectiveness of the proposed person-capacity-based optimization method. The results of extensive sensitivity analyses of the bus ratio, bus occupancy, and maximum degree of saturation of exclusive bus lanes have been presented to show the performance and applicable domain of the proposed model under different composition of inputs.     

A systematic analysis of multimodal transport systems with road space distribution and responsive bus service

A smart design of transport systems involves efficient use and allocation of the limited urban road capacity in the multimodal environment. This paper intends to understand the system-wide effect of dividing the road space to the private and public transport modes and how the public transport service provider responds to the space changes. To this end, the bimodal dynamic user equilibrium is formulated for separated road space. The Macroscopic Fundamental Diagram (MFD) model is employed to depict the dynamics of the automobile traffic for its state-dependent feature, its inclusion of hypercongestion, and its advantage of capturing network topology. The delay of a bus trip depends on the running speed which is in turn affected by bus lane capacity and ridership. Within the proposed bimodal framework, the steady-state equilibrium traffic characteristics and the optimal bus fare and service frequency are analytically derived. The counter-intuitive properties of traffic condition, modal split, and behavior of bus operator in the hypercongestion are identified. To understand the interaction between the transport authority (for system benefit maximization) and the bus operator (for its own benefit maximization), we examine how the bus operator responds to space changes and how the system benefit is influenced with the road space allocation. With responsive bus service, the condition, under which expanding bus lane capacity is beneficial to the system as a whole, has been analytically established. Then the model is applied to the dynamic framework where the space allocation changes with varying demand and demand-responsive bus service. We compare the optimal bus services under different economic objectives, evaluate the system performance of the bimodal network, and explore the dynamic space allocation strategy for the sake of social welfare maximization.     

Empirical modelling of the relationship between bus and car speeds on signalised urban networks

Vehicle speed is an important attribute for analysing the utility of a transport mode. The speed relationship between multiple modes of transport is of interest to traffic planners and operators. This paper quantifies the relationship between bus speed and average car speed by integrating Bluetooth data and transit signal priority data from the urban network in Brisbane, Australia. The method proposed in this paper is the first of its kind to relate bus speed and average car speed by integrating multi-source traffic data in a corridor-based method. Three transferable regression models relating not-in-service bus, in-service bus during peak periods and in-service bus during off-peak periods with average car speed are proposed. The models are cross-validated and the interrelationships are significant.     

Investigations of interactions between bus rapid transit and general traffic flows

Bus rapid transit (BRT) is a popular strategy to increase transit attraction because of its high‐capacity, comfortable service, and fast travel speed with the exclusive right‐of‐way. Various engineering designs of right‐of‐way and the violation enforcement influence interactions between BRT and general traffic flows. An empirical assessment framework is proposed to investigate traffic congestion and lane‐changing patterns at one typical bottleneck along a BRT corridor. The BRT bottleneck consists of bus lane, BRT station, video enforcement zone, and transit signal priority intersection. We analyze oblique cumulative vehicle counts and oblique cumulative lane‐changing maneuvers extracted from videos. The cumulative vehicle counts method widely applied in revealing queueing dynamics at freeway bottlenecks is extended to an urban BRT corridor. In the study site, we assume four lane‐changing patterns, three of which are verified by the empirical measurements. Investigations of interactions between buses and general traffic show that abnormal behaviors (such as lane violations and slow moving of the general traffic) induce 16% reduction in the saturation rate of general traffic and 17% increase in bus travel time. Further observations show that the BRT station and its induced increasing lane‐changing maneuvers increase the downstream queue discharge flows of general traffic. The empirical results also contribute to more efficient strategies of BRT planning and operations, such as alternative enforcement methods, various lane separation types, and optimized traffic operations. Copyright © 2014 John Wiley & Sons, Ltd.     

Modeling the impacts of mandatory and discretionary lane-changing maneuvers

In this paper, a novel mesoscopic multilane model is proposed to enable simultaneous simulation of mandatory and discretionary lane-changing behaviors to realistically capture multilane traffic dynamics. The model considers lane specific fundamental diagrams to simulate dynamic heterogeneous lane flow distributions on expressways. Moreover, different priority levels are identified according to different lane-changing motivations and the corresponding levels of urgency. Then, an algorithm is proposed to estimate the dynamic mandatory and discretionary lane-changing demands. Finally, the lane flow propagation is defined by the reaction law of the demand–supply functions, which can be regarded as an extension of the Incremental-Transfer and/or Priority Incremental-Transfer principles. The proposed mesoscopic multilane cell transmission model is calibrated and validated on a complex weaving section of the State Route 241 freeway in Orange County, California, showing both the positive and negative impact of lane changing maneuvers, e.g., balancing effect and capacity drop, respectively. Moreover, the empirical study verifies that the model requires no additional data other than the cell transmission model does. Thus, the proposed model can be deployed as a simple simulation tool for accessing dynamic mesoscopic multilane traffic state from data available to most management centers, and also the potential application in predicting the impact of traffic incident or lane control strategy.     

An analytical model to conduct a person-based evaluation of transit preferential treatments on signalized arterials

The complexities of urban transportation networks where multiple modes with different characteristics and needs travel in combination with constraints on space and funding make the sustainable management of these systems a challenge. In order to improve transit service, space (e.g., dedicated bus lanes) and time (e.g., transit signal priority strategies) Transit Preferential Treatments (TPT) are deployed to improve transit operations. The objective of this paper is to develop an analytical model that allows for a person-based evaluation of alternative TPTs when considered individually and in combination. In particular, the analytical model is developed to assess person delay and person discharge flow at any intersection that is part of a signalized arterial, where auto arrivals are in platoons. The performance of TPTs is evaluated using both the analytical model and through microsimulation tests on two intersections of San Pablo Avenue in Berkeley, CA. Space TPTs such as dedicated bus lanes and queue jumper lanes are beneficial in reducing bus person delay when provided in addition to the existing lanes; however, the effectiveness of time TPTs such as green extension depends on the level of auto demand in combination with signal settings. Changes in person discharge flow are not significant for any of the treatments tested with the exception of the bus lane substitution with and without green extension, which led to a significant decrease in person discharge flow. Increased bus frequency increases the effectiveness of transit signal priority in reducing total and bus person delay. The analytical model results produce ranking outcomes that are comparable with the microsimulation ones and therefore, the model may be used for a quantitative evaluation of TPTs without the need for data intensive and time consuming calibration efforts required for microsimulation models. The developed model can be used to guide infrastructure and investment decisions on where such TPTs should be implemented and under what conditions space TPTs should be combined with time TPTs to improve person mobility.     

Analytical and simulation approaches to understand combined effects of transit signal priority and road-space priority measures

Transit signal priority (TSP) may be combined with road-space priority (RSP) measures to increase its effectiveness. Previous studies have investigated the combination of TSP and RSP measures, such as TSP with dedicated bus lanes (DBLs) and TSP with queue jump lanes (QJLs). However, in these studies, combined effects are usually not compared with separate effects of each measure. In addition, there is no comprehensive study dedicated to understanding combined effects of TSP and RSP measures. It remains unclear whether combining TSP and RSP measures creates an additive effect where the combined effect of TSP and RSP measures is equal to the sum of their separate effects. The existence of such an additive effect would suggest considerable benefits from combining TSP and RSP measures. This paper explores combined effects of TSP and RSP measures, including TSP with DBLs and TSP with QJLs. Analytical results based on time-space diagrams indicate that at an intersection level, the combined effect on bus delay savings is smaller than the additive effect if there is no nearside bus stop and the traffic condition in the base case is under-saturated or near-saturated. With a near-side bus stop, the combined effect on bus delay savings at an intersection level can be better than the additive effect (or over-additive effect), depending on dwell time, distance from the bus stop to the stop line, traffic demand, and cycle length. In addition, analytical results suggest that at an arterial level, the combined effect on bus delay savings can be the over-additive effect with suitable signal offsets. These results are confirmed by a micro-simulation case study. Combined effects on arterial and side-street traffic delays are also discussed.     

Evaluation of exclusive bus lanes in a bi-modal degradable road network

In this paper, we proposed an evaluation method of exclusive bus lanes (EBLs) in a bi-modal degradable road network with car and bus transit modes. Link travel time with and without EBLs for two modes is analyzed with link stochastic degradation. Furthermore, route general travel costs are formulated with the uncertainty of link travel time for both modes and the uncertainty of waiting time at a bus stop and in-vehicle congestion costs for the bus mode. The uncertainty of bus waiting time is considered to be relevant to the degradation of the front links of the bus line. A bi-modal user equilibrium model incorporating travelers’ risk adverse behavior is proposed for evaluating EBLs. Finally, two numerical examples are used to illustrate how the road degradation level, travelers’ risk aversion level and the front link’s correlation level with the uncertainty of the bus waiting time affect the results of the user equilibrium model with and without EBLs and how the road degradation level affects the optimal EBLs setting scheme. A paradox of EBLs setting is also illustrated where adding one exclusive bus lane may decrease share of bus.     

Categorization of the lane change decision process on freeways

Traffic operations for new road layouts are often simulated using microscopic traffic simulation packages. These traffic simulation packages usually simulate traffic on freeways by a combination of a car-following model and a lane change model. The car-following models have gained attention of researchers and are well calibrated versus data. The proposed lane change models are often representations of assumed reasonable behavior, not necessarily corresponding to reality. The current simulation packages apply solely one specific type of model for car-following or lane changing for all vehicles during the simulation. This paper investigates the decision process of lane changing maneuvers for a variety of drivers based on a two-stage test-drive. Participants are asked to take a drive on a freeway in the Netherlands in a camera-equipped vehicle. Afterwards, the drivers are asked to comment on their choices related to lane and speed choice, while watching the video. This paper reveals that different drivers have completely different strategies to choose lanes, and the choices to change lane are related to their speed choice. Four distinct strategies are empirically found. These strategies differ not only in parameter values, as is currently being modeled in most simulation packages, but also in their reasoning. Most remarkably, all drivers perceive their strategy as an obvious behavior and expect all other drivers to drive in a similar way. In addition to the interviews of the participants in the test-drive, 11 people who did not take part in the experiment were interviewed and questioned on lane change decisions. Moreover, the findings of this study have been presented to various groups of audience with different backgrounds (about 150 people). Their comments and feedback on the derived driving strategies have added some value to this study. The findings in this paper form a starting point for developing a novel lane change model which considers four different driving strategies among the drivers on freeway. This is a significant contribution in the area of driving behavior modeling, since the existing microscopic simulators consider only one type of lane change models for all drivers during the simulation. This could lead to significant changes in the way lane changes on freeways are modeled.     

Establishing speed–flow–density relationships for exclusive motorcycle lanes

Abstract

The motorcycle is a popular mode of transport in Malaysia and developing Asian countries, but its significant representation in the traffic mix results in high rates of motorcycle accidents. As a result, the Malaysian Government decided to segregate motorcycle traffic along its new federal roads as an engineering approach to reduce accidents. However, traffic engineers needed to know the maximum traffic a motorcycle lane could accommodate. Despite substantial literature related to speed–flow–density relationships and capacities of various transport facilities, there is a knowledge gap regarding motorcycle lanes. This paper establishes motorcycle speed–flow–density relationships and capacities of exclusive motorcycle lanes in Malaysia. Observations of motorcycle flows and speeds were conducted along existing and experimental motorcycle lanes. Motorcycle speed–density data were aggregated and plotted for two types of observable motorcycle riding behaviour patterns that were influenced by the widths of a motorcycle lane: the headway pattern (lane width ≤ 1.7 m) and the space pattern (lane width > 1.7 m). For both riding patterns, regression analysis of motorcycle speed–density data best fits the logarithmic model and consequently the motorcycle flow–density and speed–flow models are derived. Motorcycle lane capacities for headway and space riding patterns are estimated as 3300 mc/hr/lane and 2200 mc/hr/m, respectively.     

A network wide simulation strategy of alternative fuel vehicles

This paper presents an integrated simulator “CUIntegration” to evaluate routing strategies based on energy and/or traffic measures of effectiveness for any Alternative Fuel Vehicles (AFVs). The CUIntegration can integrate vehicle models of conventional vehicles as well as AFVs developed with MATLAB-Simulink, and a roadway network model developed with traffic microscopic simulation software VISSIM. The architecture of this simulator is discussed in this paper along with a case study in which the simulator was utilized for evaluating a routing strategy for Plug-in Hybrid Electric Vehicles (PHEVs) and Electric Vehicles (EVs). The authors developed a route optimization algorithm to guide an AFV based on that AFV driver’s choice, which included; finding a route with minimum (1) travel time, (2) energy consumption or (3) a combination of both. The Application Programming Interface (API) was developed using Visual Basic to simulate the vehicle models/algorithms developed in MATLAB and direct vehicles in a roadway network model developed in VISSIM accordingly. The case study included a section of Interstate 83 in Baltimore, Maryland, which was modeled, calibrated and validated. The authors considered a worst-case scenario with an incident on the main route blocking all lanes for 30 min. The PHEVs and EVs were represented by integrating the MATLAB-Simulink vehicle models with the traffic simulator. The CUIntegration successfully combined vehicle models with a roadway traffic network model to support a routing strategy for PHEVs and EVs. Simulation experiments with CUIntegration revealed that routing of PHEVs resulted in cost savings of about 29% when optimized for the energy consumption, and for the same optimization objective, routing of EVs resulted in about 64% savings.     

An applicatoin of an optimal traffic control during lane closure periods of a two‐lane road

On two‐lane roadways, when provision should be made for alternative one‐way movement (for construction or maintenance), the traffic characteristics differ from normal operation in which no lane is closed. The purpose of this study is to derive optimal strategies for controlling, by means of traffic signals, the one lane operation (in two‐way roadways). In this study, strategies to determine the optimal length of the closed one‐lane section during construction and maintenance work are established. This length minimizes the objective function representing the tradeoff between delay cost and operational cost. Using the length value obtained by the proposed model, plus a timing methodology, the overall cost of operating the closed highway section can be minimized. The sensitivity analysis of the optimal solution for the section length is examined with respect to the input variables. This analysis shows that for very low traffic flow values (less than 100 vph per direction), the solution is very sensitive to fuel price changes, while for greater flow values, the solution is insensitive to this change. Similar results are obtained for changes in the worker's wage which is part of both the operational and the delay cost. That is, the section's length is sensitive to wage changes at low traffic flow and insensitive otherwise. Based on the results presented in this study, it is possible to establish a guideline for the section's length determination. The control measure can emerge from a pair of traffic signals that can be installed at both ends of the closed highway segment. This traffic control system is also described in the study in terms of its components and operational features and advantages.     

A Cooperative Intelligent Transport Systems (C‐ITS)‐based lane‐changing advisory for weaving sections

Weaving sections, a common design of motorways, require extensive lane‐change manoeuvres. Numerous studies have found that drivers tend to make their lane changes as soon as they enter the weaving section, as the traffic volume increases. Congestion builds up as a result of this high lane‐changing concentration. Importantly, such congestion also limits the use of existing infrastructure, the weaving section downstream. This behaviour thus affects both safety and operational aspects. The potential tool for managing motorways effectively and efficiently is cooperative intelligent transport systems (C‐ITS). This research investigates a lane‐change distribution advisory application based on C‐ITS for weaving vehicles in weaving sections. The objective of this research is to alleviate the lane‐changing concentration problem by coordinating weaving vehicles to ensure that such lane‐changing activities are evenly distributed over the existing weaving length. This is achieved by sending individual messages to drivers based on their location to advise them when to start their lane change. The research applied a microscopic simulation in aimsun to evaluate the proposed strategy's effectiveness in a one‐sided ramp weave. The proposed strategy was evaluated using different weaving advisory proportions, traffic demands and penetration rates. The evaluation revealed that the proposed lane‐changing advisory has the potential to significantly improve delay. Copyright © 2016 John Wiley & Sons, Ltd.     

A microscopic analysis of speed deviation impacts on lane-changing behavior

Driving behavior models that capture drivers’ tactical maneuvering decisions in different traffic conditions are essential to microscopic traffic simulation systems. This paper focuses on a parameter that has a great impact on road users’ aggressive overtaking maneuvers and directly affects lane-changing models (an integral part of microscopic traffic simulation models), namely, speed deviation. The objective of this research is to investigate the impacts of speed deviation in terms of performance measures (delay time, network mean speed, and travel time duration) and the number of lane-change maneuvers using the Aimsun traffic simulator. Following calibration of the model for a section of urban highway in Tehran, this paper explores the sensitivity of lane-changing maneuvers during different speed deviations by conducting two types of test. Simulation results show that, by decreasing speed deviation, the number of lane changes reduces remarkably and so network safety increases, thus reducing travel time due to an increase in network mean speed.     

Modelling lane changing and merging in microscopic traffic simulation

This paper introduces Simulation of Intelligent TRAnsport Systems (SITRAS), a massive multi-agent simulation system in which driver-vehicle objects are modelled as autonomous agents. The simulation outputs can be used for the evaluation of Intelligent Transport Systems applications such as congestion and incident management, public transport priority and dynamic route guidance. The model concepts and specifications, and the first applications of the model in the area of incident modelling in urban arterial networks were described in previous publications. This paper presents the details of the lane changing and merging algorithms developed for the SITRAS model. These models incorporate procedures for ‘forced’ and ‘co-operative’ lane changing which are essential for lane changing under congested (and incident-affected) traffic conditions. The paper describes the algorithms and presents simulation examples to demonstrate the effects of the implemented models. The results indicate that only the forced and cooperative lane changing models can produce realistic flow-speed relationships during congested conditions.     

Optimal subwork zone operational strategy for short‐term work zone projects in four‐lane two‐way freeways

Roadside trees in Singapore are regularly trimmed for the purpose of traffic safety and roadside tree‐trimming project is one typical type of short‐term work zone projects. To implement such a short‐term work zone project, contractors usually divide an entire work zone into multiple subwork zones with the uniform length. This paper aims to determine an optimal subwork zone strategy for the short‐term work zone projects in four‐lane two‐way freeways with time window and uniform subwork zone length constraints. The deterministic queuing model is employed to estimate total user delay caused by the work zone project by taking into account variable traffic speeds. Based on the user delay estimations, this paper proceeds to build a minimization model subject to time window and uniform length constraints for the optimal subwork zone strategy problem. This paper also presents a variation of the minimization model to examine the impact of unequal subwork zone length constraint. Since these minimization models belong to the mixed‐integer non‐differentiable optimization problems, an iterative algorithm embedding with the genetic simulated annealing method is thus proposed to solve these models. Finally, a numerical example is carried out to investigate the effectiveness of the proposed models. Copyright © 2010 John Wiley & Sons, Ltd.