Effect of internal flow on vortex-induced vibration dynamics of a flexible mining riser in external shear current

Vortex-induced vibration (VIV) of flexible risers with both internal and external flows has received much attention recently. Hence, VIV dynamics of a fluid-conveying flexible riser subjected to external shear current is investigated. The effect of internal flow velocity and fluid density on VIV response is mainly examined and analyzed. A time domain model is introduced and elaborated. Then the finite element method is adopted to discretize the governing equations. Firstly, the model is validated based on the comparison between the numerical and experimental results. Then the influence of the internal flow velocity and fluid density on VIV dynamics is studied. The results show that multi-frequency response occurs when the flexible riser with various internal flow velocities and densities is subjected to external shear current. Under same shear current velocity, the IL mean deflection is enlarged with the increase of the internal flow velocity and fluid density. In addition, the internal flow velocity and fluid density have an evident effect on the vibrating frequency and the root mean square (RMS) displacement in both in-line (IL) and cross-flow (CF) directions. Moreover, mode and frequency transitions can be observed under different internal flow velocities and fluid densities.     

计及海底井口影响的隔水管涡激振动响应特性试验

在靠近海底井口位置,隔水管周围流场受井口系统的影响发生变化,流固耦合下涡激振动可能诱发隔水管在横流向(CF方向)更为剧烈的振动。为了研究受管土装置影响的隔水管涡激振动响应特性,使用自主设计的管土装置模拟海底井口,采用8 m柔性立管,进行了均匀流下单管和受管土装置影响的涡激振动对比试验。试验通过FBG光纤应变片测得应变信息,使用模态叠加法、FFT变换处理分析试验数据,对比分析2组隔水管的主导频率、应变时历与幅值谱、无因次振幅以及激励力系数等参数沿管径的分布情况。结果发现管土装置影响下,隔水管主导频率减小;CF方向涡激振动增大,振幅沿径向呈非对称特征;涡激振动振幅更大,隔水管受流场的激励与阻尼更为剧烈。     

剪切来流下柔性立管涡激振动抑制装置试验研究

文章针对柔性立管螺旋列板抑制装置在剪切流场中的涡激振动响应特性进行了试验研究,试验过程中通过旋转臂架从而形成相对剪切来流。通过测试得到的应变数据,基于模态叠加法,可得到立管的位移响应等参数。试验中针对螺旋列板的螺距和鳍高的变化进行了分析,系统地研究了不同螺旋列板状态下立管的主导频率、主导模态、无量纲振幅比以及疲劳损伤等参数。研究结果表明：螺旋列板可以很好地抑制立管的涡激振动响应;与螺距相比,鳍高对立管涡激振动响应会带来更大的影响;剪切流场中立管螺距恒定为5.0D（D为立管外径）时,鳍高为0.15D时的立管具有最好的抑制效果。     

表面粗糙度对立管涡激振动响应影响的试验研究

应用模型试验的方法,研究了表面粗糙度对立管涡激振动响应特性的影响规律,对不同粗糙度条件下立管所受拖曳力、升力、端部张力、漩涡泄放频率、结构振动响应频率、位移响应等参数的变化规律进行了对比分析。结果表明：与立管横向振动相比,立管流向振动更早出现锁定现象,因此当折合速度较低时,立管流向振动的涡激振动响应要大于横向振动。立管张力均存在两个峰值频率,其中一个峰值频率为主导频率,与拖曳力主导频率吻合,由流向涡激振动所产生;另一个峰值频率为主导频率的一半,与升力主导频率吻合,由横向涡激振动所产生。因此可以看出：横向涡激振动与流向涡激振动通过张力作用而相互影响。与光滑立管相比,表面粗糙度降低了立管的涡激振动位移响应,减小了涡激振动的锁定区域,但提高了漩涡泄放频率。对于不同粗糙度下的粗糙立管,随着粗糙度的增加,立管的锁定区域开始点逐渐提前,锁定结束点逐渐推迟,锁定区域逐渐变宽。     

振荡来流下柔性立管涡激振动响应特性试验研究

在顶部浮体的带动下,悬链线立管的动力响应会诱发其周围产生相对来流,而这种振荡来流将激励立管悬垂段产生“间歇性”的涡激振动。文章在海洋工程水池中对不同最大约化速度URmax、KC数组合下的振荡来流作用下的柔性立管开展模型试验研究,利用光纤应变片测量模型的涡激振动响应。结合模态分析与小波变换对试验数据进行分析,讨论并总结了最大约化速度URmax以及KC数对涡激振动位移幅值响应特性的影响规律。文中进一步分析发现振荡来流下的涡激振动响应还存在“迟滞”及“高阶谐频”现象。     

平台运动对深水钻井隔水管非线性动力响应的影响

文章建立了波浪、海流和船体运动等载荷综合作用下的深水钻井隔水管非线性时域动力响应模型,模型考虑了顶部张力和隔水管内部泥浆对隔水管动力响应的影响,计人了张力沿隔水管长度的变化,并采用有限差分法求解了四阶偏微分运动方程.计算了随机波浪和规则波浪下船体运动对深水钻井隔水管非线性动力响应的影响,研究分析了船体平均偏移以及波频响应和低频响应的周期和幅值对深水钻井隔水管动力响应的影响.结果表明,船体运动对深水钻井隔水管动力响应有较大的影响,在随机波浪和海流作用下,考虑船体运动时,隔水管上部最大弯矩增大了59%.船体的平均偏移主要影响底部最大弯矩.船体波频运动对上部最大弯矩有较大影响,随着波频响应的周期和幅值的变化,上部最大弯矩变化较快,而低频响应的则主要影响隔水管上部弯矩.     

并联布置立管涡激振动抑制装置试验研究

针对分隔板、控制杆和减振器3种涡激振动抑制装置,在波流水槽中进行不同间距下并联布置立管的裸管试验以及抑振管涡激振动试验研究,对比分析3种抑制装置的抑制效果。试验结果表明:在同一流速条件下,附加抑振装置后立管的振动振幅与裸管相比明显降低,所采用的3种抑振装置在不同程度上均抑制海洋立管的涡激振动;从横向振动最优抑制效果来讲,控制杆的效果最好;从顺流向振动最优抑制效果来讲,控制杆和分隔板的效果好,减振器的效果较弱。综合比较不同工况下各个间距和振动方向的最优抑制效果发现,控制杆的最优抑制效果最好,能够对并联立管横向和顺流向的振动起到很好的抑制效果。     

非粘结柔性立管静态分析

海洋柔性立管因材料和结构上的复杂性在设计分析中存在许多技术难题。本文在变形能原理和能量守恒的基础上,推导出了柔性立管各层的刚度矩阵。将各层刚度矩阵进行叠加,得到柔性立管总体刚度矩阵,并用总体刚度矩阵求解静载荷作用下立管变形响应。同时基于ABAQUS软件建立八层非粘结柔性立管有限元模型,并将有限元计算结果和刚度矩阵计算结果进行比较。结果分析表明：运用推导得到的刚度矩阵求解静态载荷下立管的变形是一种简便且准确的方法。     

串列双立管涡激振动抑制研究

实际工程中深海立管常以管群的方式出现,当立管彼此相互靠近时,会发生流场干涉效应。为研究立管间相互干涉作用及螺旋侧板抑制双立管涡激振动的效果,本文基于Ansys Workbench平台,采用双向流固耦合技术对Re=7800均匀来流下长径比为482的串列双立管进行三维数值模拟。结果表明,立管轴间距为5D时立管间有完整的涡旋脱落,下游立管在上游立管的尾流诱导下产生振动,双立管横向振动锁定在二阶模态,且振动方向相反。附加螺旋侧板能有效削弱双立管振动频率,降低上游立管横向振动幅值,但下游立管两向位移响应变化不大。     

Mechanical model and characteristics of deep-water drilling riser-wellhead system under internal solitary waves

Internal solitary waves with a huge amount of energy easily trigger the large dynamic responses of riser-wellhead system and threaten its structural safety. However, previous studies have only focused on the dynamic response of the riser under internal solitary waves. The riser may experience excessive traction from the platform, especially from the mooring platform, in response to the arrival of internal solitary waves. The bottom of the riser connects to the wellhead system, which in turn exerts a reaction force on the riser. To address this problem, a coupled dynamic model of deep-water drilling mooring platform-riser-wellhead system under internal solitary waves is developed in this paper. A dynamic response analysis method based on the fourth-order Runge-Kutta method and finite element method is also proposed for the mooring platform-riser-wellhead system. A dynamical solver for the coupled system is then developed using MATLAB. The dynamic response characteristics of the riser-wellhead system under internal solitary waves are calculated. Results show that the displacement and bending moment of the system initially increases and then decreases along with the propagation of internal solitary waves, and finally reach equilibrium position. The displacement and bending moment reach their peak before the trough of internal solitary waves passes through the riser-wellhead system. The dynamic responses of the riser-wellhead system under the influence of internal solitary wave loads are much larger than those without the effect of internal solitary wave loads. The riser system experiences shearing loads at the interface of internal solitary waves, which trigger a step-like bending moment variation. The bending moment of the conductor under the mudline is greatly increased by the internal solitary waves.     

细长海洋结构物涡激振动研究综述

随着世界范围内深海石油开采的需要,近年来关于海洋结构物涡激振动的研究越来越受到重视.虽然此问题在数值模拟和实验方面都已取得了一定的进展,但是还有许多问题尚待解决.同时,新型海洋结构物的引入给涡激振动的预报方法和抑振手段提出了新的挑战.因此,细长海洋结构物的涡激振动仍将是未来几年里备受关注的研究课题.本文在介绍有关涡激振动基本概念和理论背景的基础上,总结了近年来关于以深水立管为代表的海洋结构物涡激振动的研究与进展,包括对现有涡激振动分析工具的分类与评估;对柱体及海洋结构物涡激振动的实验研究;对深水立管与涡激振动相关的疲劳评估准则的研究;海洋结构物的横向、流向及轴向涡激振动的耦合作用研究;关于海洋结构物涡激振动的抑振措施和设备的理论及实验研究.本文着重介绍了计算流体力学方法在海洋结构物涡激振动研究中的应用和进展.最后,对海洋结构物涡激振动相关的研究热点的现状进行了总结并对今后工作提出了展望.     

参激振动对顺应式垂直通路立管涡激振动的影响

顺应式垂直通路立管(CVAR)是目前处于研究阶段的一种新型的立管类型,在海流作用下产生涡激振动,在平台垂荡运动作用下产生参数激励振动。为了研究参数激励的影响,本文引入尾流振子模型模拟漩涡脱落对立管的作用,同时考虑浮式平台升沉运动产生的参数激励,建立了CVAR参激-涡激联合振动方程,获取联合作用下的动力响应,并与纯涡激振动响应进行对比。结果表明,在相同的流速下CVAR中部涡激振动幅值最大,流速的增大会导致涡激振动的频率增大,发生高阶锁振,高阶锁振振动幅值比低阶锁振振动幅值小。考虑参数激励之后,较纯涡激振动而言,立管的振动幅值增大;当参激频率与涡激振动频率接近时,立管的振动幅值最大。     

柔性立管涡激振动响应轨迹特性研究

为了深入研究细长柔性立管的涡激振动响应特性,进行了柔性立管的拖曳水池试验。由拖车拖动立管产生相对来流,根据应变测试得到的应变数据,基于模态叠加法得到位移响应。试验分析前,通过数值方法先针对刚性立管的涡激振动响应轨迹特性进行了分析。紧接着,通过试验方法对柔性立管的单模态以及多模态涡激振动响应轨迹特性进行了深入的分析和讨论。通过分析发现:柔性立管在低速下具有与刚性立管类似的轨迹响应特性,均呈现经典的8字形状;柔性立管在高速下,其轨迹开始变得混乱,这主要是由位移的多模态响应特性所产生。     

两自由度不同截面形式柱体涡激振动的CFD数值模拟

文章采用计算流体力学（CFD）方法,结合SST k-棕湍流模型,对低质量比柱体进行两自由度涡激振动数值模拟,得到了柱体升力、曳力系数的时程曲线,并观察了柱体进入锁振状态的幅值变化,研究了不同截面形式柱体在外流速处于0.1-1.0 m/s范围内的振动响应。将圆柱体在不同流速下两向振动的CFD数值模拟与实验数据进行比较,得到了较为满意的结果。通过分析不同截面柱体在不同外流速下的振动幅值发现,带有抑振装置的柱体截面形式能够有效地减小涡激振动,其中,板状截面柱体抑振效果较好。     

螺旋侧板的高度对VIV影响的CFD分析

深水立管在来流作用下容易产生流向和横向的周期性位移振动(VIV),这种流固耦合作用会加剧立管结构疲劳,最终导致其功能失效。之前的研究发现螺旋侧板可以有效的抑制VIV的影响,其中侧板高度和螺距等几何参数决定其抑制效率。文章主要基于CFD对不同高度螺旋侧板的立管的尾流场进行数值模拟。结果表明:在研究范围内,螺旋侧板随高度增大抑制VIV效果越好,在H=0.25D(D为立管直径)时作用最佳,但拖曳力系数明显增大,同时来流方向和螺旋侧板的夹角也会影响其抑制效率。     

耦合非线性三维海洋立管的边界控制(英文)

This paper presents a design of boundary controllers implemented at the top end for global stabilization of a marine riser in a three dimensional space under environmental loadings. Based on the energy approach, nonlinear partial differential equations of motion, including bending-bending and longitudinal-bending couplings for the risers are derived. The couplings cause mutual effects between the three independent directions in the riser’s motions, and make it difficult to minimize its vibrations. The Lyapunov direct method is employed to design the boundary controller. It is shown that the proposed boundary controllers can effectively reduce the riser’s vibration. Stability analysis of the closed-loop system is performed using the Lyapunov direct method. Numerical simulations illustrate the results.     

水下压缩空气储能系统柔性立管响应特性分析（英文）

With the rapid development of marine renewable energy technologies, the demand to mitigate the fluctuation of variable generators with energy storage technologies continues to increase. Offshore compressed air energy storage(OCAES) is a novel flexible-scale energy storage technology that is suitable for marine renewable energy storage in coastal cities, islands, offshore platforms, and offshore renewable energy farms. For deep-water applications, a marine riser is necessary for connecting floating platforms and subsea systems. Thus, the response characteristics of marine risers are of great importance for the stability and safety of the entire OCAES system. In this study, numerical models of two kinds of flexible risers, namely, catenary riser and lazy wave riser, are established in OrcaFlex software. The static and dynamic characteristics of the catenary and the lazy wave risers are analyzed under different environment conditions and internal pressure levels. A sensitivity analysis of the main parameters affecting the lazy wave riser is also conducted. Results show that the structure of the lazy wave riser is more complex than the catenary riser; nevertheless, the former presents better response performance.     

Application of analytical model in the prediction of dynamic responses and fatigue damage of flexible risers: Part II – Dynamic analysis of flexible risers in large-scale domain using a direct moment correction method

In recent years, the dynamic responses of flexible risers have been the focus of many researchers. Most flexible risers undergo a substantial level of irregular motion from environmental loadings, which involves a continuous slip of helical wires. The slip of helical wires especially leads to a hysteretic effect by reducing the bending stiffness, making it hard to predict the dynamic responses of flexible risers. The current study, as an extension to Part I, presents a new large-scale dynamic analysis method for flexible risers. The suggested method creates a large-scale model for the dynamic analysis that considers a geometric and bending nonlinearity of flexible risers. The kinematics of each beam element is formulated based on a Green-Lagrangian strain and the interaction with the seabed, providing a realistic analysis of flexible risers. In particular, the current study introduces a direct moment correction method that modifies the internal force vector using an improved analytical model. The improved analytical model is assigned at each node of the large-scale model and estimates an accurate bending hysteresis curve considering the effect of shear deformation and varying tension. The suggested method corrects the bending moment and shear force of all beam elements based on the bending hysteresis curves obtained from the improved analytical model, by which a complex bending behavior of flexible risers is reflected in a large-scale domain. As a result, this study achieves a more accurate prediction of the dynamic responses and fatigue damage of flexible risers. A new dynamic analysis program, called OPFLEX, is developed herein based on the suggested analysis method. Using the developed program, the current study conducts several numerical investigations to identify the effect of the shear deformation and varying tension. Consequently, it is confirmed that the shear deformation of internal layers reduces the fatigue damage of helical wires by delaying the increase of internal stress. It is also identified that the effect of varying tension deteriorates the fatigue life of flexible risers through a continuous change of contact pressure during bending.     

超深水钻井隔水管动力分析理论研究与数值模拟

随着钻井作业向深水(500～1 500m)和超深水(1 500m以上)发展,在交变海洋环境载荷波浪力、海流力和浮式钻井平台运动的共同作用下,隔水管的动态响应更加显著.文中探讨了隔水管侧向振动的数学模型、动态特性分析中的结构与环境载荷建模技术及其非线性动力分析方法,研究并对比了不同分析方法在计算效率、计算精度和工程适用性等方面的差异.介绍了时域内应用ABAQUS软件进行超深水钻井隔水管非确定性动力分析的算法与详细流程,算例比较了不同边界条件对深水钻井隔水管动态特性的影响.研究表明,时域非确定性分析最为精确但需要时间最长,且只能采用线性AIRY波浪理论;理论上,海流主要引起隔水管动态响应的时不变部分,但该时不变部分不等同于海流引起的隔水管静态响应,一种简化方法只将海浪与钻井船运动作为动载荷而不考虑海流对动态响应的贡献;钻井船运动和波浪载荷是隔水管动态响应分析主要的动载荷,对于超深水隔水管来说,钻井船运动是首要的动载荷,其慢漂运动对隔水管性能有重要影响,而波浪仅对隔水管局部产生作用.     

考虑内流和海床作用的柔性立管和钢悬链线立管非线性分析(英文)

Flexible risers and steel catenary risers often provide unique riser solutions for today’s deepwater field development. Accurate analysis of these slender structures, in which there are high-speed HP/HT internal flows, is critical to ensure personnel and asset safety. In this study, a special global coordinate-based FEM rod model was adopted to identify and quantify the effects of internal flow and hydrostatic pressure on both flexible and deepwater steel catenary risers, with emphasis on the latter. By incorporating internal flow induced forces into the model, it was found that the internal flow contributes a new term to the effective tension expression. For flexible risers in shallow water, internal flow and hydrostatic pressure made virtually no change to effective tension by merely altering the riser wall tension. In deep water the internal pressure wielded a dominant role in governing the riser effective tension and furthering the static configuration, while the effect of inflow velocity was negligible. With respect to the riser seabed interaction, both the seabed support and friction effect were considered, with the former modeled by a nonlinear quadratic spring, allowing for a consistent derivation of the tangent stiffness matrix. The presented application examples show that the nonlinear quadratic spring is, when using the catenary solution as an initial static profile, an efficient way to model the quasi-Winkler-type elastic seabed foundation in this finite element scheme.