Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

Modal analysis of real-time,real world vehicular exhaust emissions under heterogeneous traffic conditions

This study presents the characteristics of real world, real time, on-road vehicular exhaust emission namely, carbon monoxide (CO), nitric oxide (NO), hydrocarbons (HC), and carbon dioxide (CO₂) emitted under heterogeneous traffic conditions. Field experiments were performed on major category of vehicles in developing countries, i.e. two-wheelers, auto-rickshaws, cars and buses. The on-board monitoring was carried out on different corridors with varying road geometry. Results revealed that the driving cycle was dependent on the road geometry, with two lane mixed flow corridor having lot of short term events compared to that of arterial road. Vehicular emissions during idling and cruising were generally low compared to emissions during acceleration. It was also found that emissions were significantly dependent on short term events such as rapid acceleration and braking during a trip. Also, the standard emission models like COPERT and CMEM under predicted the real world emissions by 30–200% depending upon different driving modes. The on-road emissions measurements were able to capture the emission characteristics during the micro events of real world driving scenarios which were not represented by standard vehicle emission measured at laboratory conditions.     

Assessing additional fuel consumption from cabin thermal comfort and auxiliary needs on the worldwide harmonized light vehicles test cycle

Standards for fuel consumption and carbon dioxide emissions are implemented worldwide in most light-duty vehicle markets. Regulatory drive cycles, defined as specific time-speed patterns, are used to measure levels of fuel consumption and emissions. These measurements should realistically reflect real world driving performance, however there is increasing concern about their adequacy due to the discrepancies observed between certified and real world consumption and emissions values. One of the main reasons for the discrepancy is that current testing protocols do not account for non-mechanical vehicle energy needs, such as passengers’ thermal comfort needs and the use of electric auxiliaries on-board. Cabin heating and cooling can especially lead to considerable increase in vehicle energy consumption. This paper presents a simulation-based assessment framework to account for the additional fuel consumption related to the cabin thermal energy and auxiliary needs under the worldwide-harmonized light vehicles test procedure (WLTP). A vehicle cabin model is developed and the thermal comfort energy needs are derived for cooling and heating, depending on ambient external temperature under cold, moderate and warm climates. A modification to the WLTP is proposed by including the generated power profiles for thermal comfort and auxiliary needs. Dynamic programming is used to compute the fuel consumption on the modified WLTP for a rechargeable series hybrid electric vehicle (SHEV) architecture. Results show consumption increases of 20% to 96% compared to the currently adopted WLTP, depending on the considered climate.     

Analysis of real driving gaseous emissions from light-duty diesel vehicles

Increasingly strict emissions standards are providing a major impetus to vehicle manufactures for developing advanced powertrain and after-treatment systems that can significantly reduce real driving emissions. The knowledge of the gaseous emissions from diesel engines under steady-state operation and under transient operation provides substantial information to analyze real driving emissions of diesel vehicles. While there are noteworthy advances in the assessment of road vehicle emissions from real driving and laboratory measurements, detailed information on real driving gaseous emissions are required in order to predict effectively the real-time gaseous emissions from a diesel vehicle under realistic driving conditions. In this work, experiments were performed to characterize the behavior of NOx, unburned HC, CO, and CO₂ emitted from light-duty diesel vehicles that comply with Euro 6 emissions standards. The driving route fully reflected various real-world driving conditions such as urban, rural, and highway. The real-time emission measurements were conducted with a Portable Emissions Measurement System (PEMS) including a Global Positioning System (GPS). To investigate the gaseous emission characteristics, authors determined the road load coefficients of vehicle specific power (VSP) and regression coefficient between fuel use rate and VSP. Furthermore, this work revealed the correlation between the rates of average fuel use and each gaseous emission.     

Development of two driving cycles for utility vehicles

Driving cycles are used to assess vehicle fuel consumption and pollutant emissions. The premise in this article is that suburban road-work vehicles and airport vehicles operate under particular conditions that are not taken into account by conventional driving cycles. Thus, experimental data were acquired from two pickup trucks representing both vehicle fleets that were equipped with a data logger. Based on experimental data, the suburban road-work vehicle showed a mixed driving behavior of high and low speed with occasional long periods of idling. In the airport environment, however, the driving conditions were restricted to airport grounds but were characterized by many accelerations and few high speeds. Based on these measurements, microtrips were defined and two driving cycles proposed. Fuel consumption and pollutant emissions were then measured for both cycles and compared to the FTP-75 and HWFCT cycles, which revealed a major difference: at least a 31% increase in fuel consumption over FTP-75. This increased fuel consumption translates into higher pollutant emissions. When CO₂ equivalent emissions are taken into account, the proposed cycles show an increase of at least 31% over FTP-75 and illustrate the importance of quantifying fleet speed patterns to assess CO₂ equivalent emissions so that the fleet manager can determine potential gains in energy or increased pollutant emissions.     

Marginal costs of freeway traffic congestion with on-road pollution exposure externality

The health cost of on-road air pollution exposure is a component of traffic marginal costs that has not previously been assessed. The main objective of this paper is to introduce on-road pollution exposure as an externality of traffic, particularly important during traffic congestion when on-road pollution exposure is highest. Marginal private and external cost equations are developed that include on-road pollution exposure in addition to time, fuel, and pollution emissions components. The marginal external cost of on-road exposure includes terms for the marginal vehicle’s emissions, the increased emissions from all vehicles caused by additional congestion from the marginal vehicle, and the additional exposure duration for all travelers caused by additional congestion from the marginal vehicle. A sensitivity analysis shows that on-road pollution exposure can be a large portion (18%) of marginal social costs of traffic flow near freeway capacity, ranging from 4% to 38% with different exposure parameters. In an optimal pricing scenario, excluding the on-road exposure externality can lead to 6% residual welfare loss because of sub-optimal tolls. While regional pollution generates greater costs in uncongested conditions, on-road exposure comes to dominate health costs on congested freeways because of increased duration and intensity of exposure. The estimated marginal cost and benefit curves indicate a theoretical preference for price controls to address the externality problem. The inclusion of on-road exposure costs reduces the magnitudes of projects required to cover implementation costs for intelligent transportation system (ITS) improvements; the net benefits of road-pricing ITS systems are increased more than the net benefits of ITS traffic flow improvements. When considering distinct vehicle classes, inclusion of on-road exposure costs greatly increases heavy-duty vehicle marginal costs because of their higher emissions rates and greater roadway capacity utilization. Lastly, there are large uncertainties associated with the parameters utilized in the estimation of health outcomes that are a function of travel pollution intensity and duration. More research is needed to develop on-road exposure modeling tools that link repeated short-duration exposure and health outcomes.     

Eco-driving: An economic or ecologic driving style?

In this work the trade-off between economic, therefore fuel saving, and ecologic, pollutant emission reducing, driving is discussed. The term eco-driving is often used to refer to a vehicle operation that minimizes energy consumption. However, for eco-driving to be environmentally friendly not only fuel consumption but also pollutant emissions should be considered. In contrast to previous studies, this paper will discuss the advantages of eco-driving with respect to improvements in fuel consumption as well as pollutant gas emissions. Simulating a conventional passenger vehicle and applying numerical trajectory optimization methods best vehicle operation for a given trip is identified. With hardware-in-the-loop testing on an engine test bench the fuel and emissions are measured. An approach to integrate pollutant emission and dynamically choose the ecologically optimal gear is proposed.     

A statistical model for estimating oxides of nitrogen emissions from light duty motor vehicles

Motor vehicle emission rate models for predicting oxides of nitrogen (NOx) emissions are insensitive to vehicle modes of operation such as cruise, acceleration, deceleration, and idle, because they are based on average trip speed. Research has shown that NOx emissions are sensitive to engine load; hence, load-based variables need to be included in emissions models. Ongoing studies attempting to incorporate these `modal' variables have experienced difficulties with: (1) incomplete and/or non-representative data sets of emissions test data vis-a-vis the modal operating profiles of the tested vehicles; (2) lack of information for predicting on-road operating parameters of vehicles; and (3) non-representative vehicles recruited for emissions tests.The objective of this research was to develop a statistical model for predicting NOx emissions from light-duty gasoline motor vehicles. The primary end use of this model is forecasting, rather than explanation of the factors that affect NOx emissions, which brings to bear different requirements from the statistical model. The three challenges noted above are addressed by: (1) analyzing a data set of more than 13 000 hot-stabilized laboratory treadmill tests on 19 driving cycles (specific speed versus time testing conditions), and 114 variables describing vehicle, engine and test cycle characteristics; (2) making the models compatible with empirical data on how vehicles are being operated in-use; and (3) developing statistical weights to account for the differences in model year distributions between the emissions testing database and the current national on-road fleets.The NOx emissions model is estimated using ordinary least-squares regression techniques, with transformed response variable and regression weights. Tree regression is employed as a tool for mining relationships among variables in the data, with particular focus on identifying useful interactions among discrete variables. Details of the model development process are presented, as well as results for the final model showing the predicted emissions algorithm for the current motor vehicle fleet in Atlanta, GA metropolitan region.     

Exhaust emissions and fuel consumption of a triple-fuel spark-ignition engine powered passenger car

This paper examines the influence of compressed natural gas, liquefied petroleum gas and gasoline fuel on the exhaust emissions and the fuel consumption of a spark-ignition engine powered passenger car. The vehicle was driven according to the urban driving cycle and extra urban driving cycle speed profiles with the warmed-up engine. Cause and effect based analysis reveals potential for using different fuels to reduce vehicle emission and deficiencies associated with particular fuels. The highest tank to wheel efficiency and the lowest CO₂ emission are observed with the natural gas fuelled vehicle, that also featured the highest total hydrocarbon emissions and high NO_x emissions because of fast three way catalytic converter aging due the use of the compressed natural gas. Retrofitted liquefied petroleum gas fuel supply systems feature the greatest air-fuel ratio variations that result in the lowest TtW efficiency and in the highest NO_x emissions of the liquefied gas fuelled vehicle.     

Influence of driving patterns on vehicle emissions: A case study for Latin American cities

On-board real-time emission experiments were conducted on 78 light-duty vehicles in Bogota. Direct emissions of carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x) and hydrocarbons (HC) were measured. The relationship between such emissions and vehicle specific power (VSP) was established. The experimental matrix included both gasoline-powered and retrofit dual fuel (gasoline–natural gas) vehicles. The results confirm that VSP is an appropriate metric to obtain correlations between driving patterns and air pollutant emissions. Ninety-five percent of the time vehicles in Bogota operate in a VSP between −15.2 and 17.7 kW ton⁻¹, and 50% of the time they operate between −2.9 and 1.2 kW ton⁻¹, representing low engine-load and near-idling conditions, respectively. When engines are subjected to higher loads, pollutant emissions increase significantly. This demonstrates the relevance of reviewing smog check programs and command-and-control measures in Latin America, which are widely based on static (i.e., idling) emissions testing. The effect of different driving patterns on the city’s emissions inventory was determined using VSP and numerical simulations. For example, improving vehicle flow and reducing sudden and frequent accelerations could curb annual emissions in Bogota by up to 12% for CO₂, 13% for CO and HC, and 24% for NO_x. This also represents possible fuel consumption savings of between 35 and 85 million gallons per year and total potential economic benefits of up to 1400 million dollars per year.     

Development a new power management strategy for power split hybrid electric vehicles

Reduction of greenhouse gas emission and fuel consumption as one of the main goals of automotive industry leading to the development hybrid vehicles. The objective of this paper is to investigate the energy management system and control strategies effect on fuel consumption, air pollution and performance of hybrid vehicles in various driving cycles. In order to simulate the hybrid vehicle, the combined feedback–feedforward architecture of the power-split hybrid electric vehicle based on Toyota Prius configuration is modeled, together with necessary dynamic features of subsystem or components in ADVISOR. Multi input fuzzy logic controller developed for energy management controller to improve the fuel economy of a power-split hybrid electric vehicle with contrast to conventional Toyota Prius Hybrid rule-based controller. Then, effects of battery’s initial state of charge, driving cycles and road grade investigated on hybrid vehicle performance to evaluate fuel consumption and pollution emissions. The simulation results represent the effectiveness and applicability of the proposed control strategy. Also, results indicate that proposed controller is reduced fuel consumption in real and modal driving cycles about 21% and 6% respectively.     

The effect of uncertainty on US transport-related GHG emissions and fuel consumption out to 2050

The future of US transport energy requirements and emissions is uncertain. Transport policy research has explored a number of scenarios to better understand the future characteristics of US light-duty vehicles. Deterministic scenario analysis is, however, unable to identify the impact of uncertainty on the future US vehicle fleet emissions and energy use. Variables determining the future fleet emissions and fuel use are inherently uncertain and thus the shortfall in understanding the impact of uncertainty on the future of US transport needs to be addressed. This paper uses a stochastic technology and fleet assessment model to quantify the uncertainties in US vehicle fleet emissions and fuel use for a realistic yet ambitious pathway which results in about a 50% reduction in fleet GHG emissions in 2050. The results show the probability distribution of fleet emissions, fuel use, and energy consumption over time out to 2050. The expected value for the fleet fuel consumption is about 450 and 350 billion litres of gasoline equivalent with standard deviations of 40 and 80 in 2030 and 2050, respectively. The expected value for the fleet GHG emissions is about 1360 and 850 Mt CO₂ equivalent with standard deviation of 130 and 230 in 2030 and 2050 respectively. The parameters that are major contributors to variations in emissions and fuel consumption are also identified and ranked through the uncertainty analysis. It is further shown that these major contributors change over time, and include parameters such as: vehicle scrappage rate, annual growth of vehicle kilometres travelled in the near term, total vehicle sales, fuel economy of the dominant naturally-aspirated spark ignition vehicles, and percentage of gasoline displaced by cellulosic ethanol. The findings in this paper demonstrate the importance of taking uncertainties into consideration when choosing amongst alternative fuel and emissions reduction pathways, in the light of their possible consequences.     

Analysis of vehicle emission measurements on the new WLTC,the NEDC and the CADC

Several studies have shown that the type-approval data is not representative for real-world usage. Consequently, the emissions and fuel consumption of the vehicles are underestimated. Aiming at a more dynamic and worldwide harmonised test cycle, the new Worldwide Light-duty Test Cycle is being developed. To analyse the new cycle, we have studied emission results of a test programme of six vehicles on the test cycles WLTC (Worldwide Light-duty Test Cycle), NEDC (New European Driving Cycle) and CADC (Common Artemis Driving Cycle). This paper presents the results of that analysis using two different approaches. The analysis shows that the new driving cycle needs to exhibit realistic warm-up procedures to demonstrate that aftertreatment systems will operate effectively in real service; the first trip of the test cycle could have an important contribution to the total emissions depending on the length of the trip; and that there are some areas in the acceleration vs. vehicle speed map of the new WLTC that are not completely filled, especially between 70 and 110 km/h. For certain vehicles, this has a significant effect on total emissions when comparing this to the CADC.     

Carbon dioxide emissions from diesel and compressed natural gas buses during acceleration

Motor vehicle emission factors are generally derived from driving tests mimicking steady state conditions or transient drive cycles. Neither of these test conditions, however, completely represents real world driving conditions. In particular, they fail to determine emissions generated during the accelerating phase – a condition in which urban buses spend much of their time. We analyse and compare the results of time-dependant emission measurements conducted on diesel and compressed natural gas buses during an urban driving cycle on a chassis dynamometer and we derive power-law expressions relating carbon dioxide emission factors to the instantaneous speed while accelerating from rest. Emissions during acceleration are compared with that during steady speed operation.     

Energy and emissions impacts of a freeway-based dynamic eco-driving system

Surface transportation consumes a vast quantity of fuel and accounts for about a third of the US CO₂ emissions. In addition to the use of more fuel-efficient vehicles and carbon-neutral alternative fuels, fuel consumption and CO₂ emissions can be lowered through a variety of strategies that reduce congestion, smooth traffic flow, and reduce excessive vehicle speeds. Eco-driving is one such strategy. It typically consists of changing a person’s driving behavior by providing general static advice to the driver (e.g. do not accelerate too quickly, reduce speeds, etc.). In this study, we investigate the concept of dynamic eco-driving, where advice is given in real-time to drivers changing traffic conditions in the vehicle’s vicinity. This dynamic strategy takes advantage of real-time traffic sensing and telematics, allowing for a traffic management system to monitor traffic speed, density, and flow, and then communicates advice in real-time back to the vehicles. By providing dynamic advice to drivers, approximately 10–20% in fuel savings and lower CO₂ emissions are possible without a significant increase in travel time. Based on simulations, it was found that in general, higher percentage reductions in fuel consumption and CO₂ emission occur during severe compared to less congested scenarios. Real-world experiments have also been carried out, showing similar reductions but to a slightly smaller degree.     

Driving cycles that reproduce driving patterns,energy consumptions and tailpipe emissions

This study presents the Energy Based Micro-trip (EBMT) method, which is a new method to construct driving cycles that represent local driving patterns and reproduce the real energy consumption and tailpipe emissions from vehicles in a given region. It uses data of specific energy consumption, speed, and percentage of idling time as criteria of acceptable representativeness. To study the performance of the EBMT, we used a database of speed, fuel consumption, and tailpipe emissions (CO₂, CO, and NO_x), which was obtained monitoring at 1 Hz, the operation of 15 heavy-duty vehicles when they operated within different traffic conditions, during eight months. The speed vs. time data contained in this database defined the local driving pattern, which was described by 19 characteristic parameters (CPs). Using this database, we ran the EBMT and described the resulting driving cycle by 19 characteristics parameters (CPs*). The relative differences between CPs and CPs* quantified how close the obtained driving cycle represented the driving pattern. To observe tendencies of our results, we repeated the process 1000 times and reported the average relative difference (ARD) and the interquartile range (IQR) of those differences for each CP.. We repeated the process for the case of a traditional Micro-trip method and compared to previous results. The driving cycles constructed by the EBMT method showed the lowest values of ARDs and IQRs, meaning that it produces driving cycles with the highest representativeness of the driving patterns, and the best reproduction of energy consumption, and tailpipe emissions.     

Measuring the success of reducing emissions using an on-board eco-driving feedback tool

This paper reports the findings of an eco-driving trial that was designed enable users to make pre-trip and on-route decisions when driving as to the optimal route to take. The basis of this paper will be to estimate how efficiently drivers are performing in relation to fuel consumption per kilometres (km). The analysis uses details on the vehicle specification, in terms of fuel efficiency, and relates this to the distance travelled to provide the user with information on the efficiency per km travelled. Eco-driving involves the training of individuals to change their driving patterns and to adapt to driving conditions. The results of the study show that eco-driving feedback is a powerful tool and how it can be used to reduce emissions.     

Fuel economy testing of autonomous vehicles

Environmental pollution and energy use in the light-duty transportation sector are currently regulated through fuel economy and emissions standards, which typically assess quantity of pollutants emitted and volume of fuel used per distance driven. In the United States, fuel economy testing consists of a vehicle on a treadmill, while a trained driver follows a fixed drive cycle. By design, the current standardized fuel economy testing system neglects differences in how individuals drive their vehicles on the road. As autonomous vehicle (AV) technology is introduced, more aspects of driving are shifted into functions of decisions made by the vehicle, rather than the human driver. Yet the current fuel economy testing procedure does not have a mechanism to evaluate the impacts of AV technology on fuel economy ratings, and subsequent regulations such as Corporate Average Fuel Economy targets. This paper develops a method to incorporate the impacts of AV technology within the bounds of current fuel economy test, and simulates a range of automated following drive cycles to estimate changes in fuel economy. The results show that AV following algorithms designed without considering efficiency can degrade fuel economy by up to 3%, while efficiency-focused control strategies may equal or slightly exceed the existing EPA fuel economy test results, by up to 10%. This suggests the need for a new near-term approach in fuel economy testing to account for connected and autonomous vehicles. As AV technology improves and adoption increases in the future, a further reimagining of drive cycles and testing is required.     

Development of the World-wide harmonized Light duty Test Cycle (WLTC) and a possible pathway for its introduction in the European legislation

This paper presents the World-wide harmonized Light duty Test Cycle (WLTC), developed under the Working Party on Pollution and Energy (GRPE) and sponsored by the European Union (with Switzerland) and Japan. India, Korea and USA have also actively contributed. The objective was to design the harmonized driving cycle from “real world” driving data in different regions around the world, combined with suitable weighting factors. To this aim, driving data and traffic statistics of light duty vehicles use were collected and analyzed as basic elements to develop the harmonized cycle. The regional driving data and weighting factors were then combined in order to develop a unified database representing the worldwide light duty vehicle driving behavior. From the unified database, short trips were selected and combined to develop a driving cycle as representative as possible of the unified database. Approximately 765,000 km of data were collected, covering a wide range of vehicle categories, road types and driving conditions. The resulting WLTC is an ensemble of three driving cycles adapted to three vehicle categories with different power-to-mass ratio (PMR). It has been designed as a harmonized cycle for the certification of light duty vehicles around the world and, together with the new harmonized test procedures (WLTP), will serve to check the compliance of vehicle pollutant emissions with respect to the applicable emissions limits and to establish the reference vehicle fuel consumption and CO₂ performance.     

Effects of driving style on the fuel consumption of city buses under different road conditions and vehicle masses

The variance in fuel consumption caused by driving style (DS) difference exceeds 10% and reaches a maximum of 20% under different road conditions, even for experienced bus drivers. To study the influence of DS on fuel consumption, a method for summarizing DS characteristic parameters on the basis of vehicle-engine combined model is proposed. With this method, the author proposes 26 DS characteristic parameters related to fuel consumption in the accelerating, normal running, and decelerating processes of vehicles. The influence of DS characteristic parameters on fuel consumption under different road conditions and vehicle masses is quantitatively analyzed on the basis of real driving data over 100,000 km. Analysis results show that the influence of DS characteristic parameters on fuel consumption changes with road condition and vehicle mass, with road condition serving a more important function. However, the DS characteristics in the accelerating process of vehicles are decisive for fuel consumption under different conditions. This study also calculates the minimum sample size necessary for analyzing the effect of DS characteristics on fuel consumption. The statistical analysis based on the real driving data over 2500 km can determine the influence of DS on fuel consumption under a given power-train configuration and road condition. The analysis results can be employed to evaluate the fuel consumption of drivers, as well as to guide the design of Driver Advisory System for Eco-driving directly.