Real-world gaseous emission characteristics of Euro 6b light-duty gasoline- and diesel-fueled vehicles

To accurately investigate vehicle emissions that have become major contributors to global air pollutants and greenhouse gases, test conditions have been transferred from laboratory type approval test cycles to real-world driving conditions. In this study, the real-world driving emissions of carbon monoxide (CO), total hydrocarbons (THC), nitrogen oxides (NO_x), and carbon dioxide (CO₂) from one gasoline and two diesel Euro 6b light-duty passenger vehicles were investigated by a portable emission measurement system (PEMS) in Lyon, France. NO_x and CO₂ emission controls remain critical to addressing the real-world driving emissions of Euro 6b vehicles. Notably, the tested gasoline vehicle emitted higher CO₂ emissions than diesel vehicles on all types of roads, especially on the urban road with an excess of 29.3–48.3%. The highest emission factors of gaseous pollutants generally occurred on the motorway for the gasoline vehicle, while on the urban road for diesel vehicles. In particular, for high-speed driving conditions, the gasoline vehicle gaseous emissions, especially NO_x emissions, were more affected by acceleration than diesel vehicle emissions. In addition, the CO emissions, especially THC emissions, for the gasoline vehicle, were more influenced by warm-start, especially cold-start, than those for diesel vehicles.     

Carbon dioxide emissions from diesel and compressed natural gas buses during acceleration

Motor vehicle emission factors are generally derived from driving tests mimicking steady state conditions or transient drive cycles. Neither of these test conditions, however, completely represents real world driving conditions. In particular, they fail to determine emissions generated during the accelerating phase – a condition in which urban buses spend much of their time. We analyse and compare the results of time-dependant emission measurements conducted on diesel and compressed natural gas buses during an urban driving cycle on a chassis dynamometer and we derive power-law expressions relating carbon dioxide emission factors to the instantaneous speed while accelerating from rest. Emissions during acceleration are compared with that during steady speed operation.     

Analyzing spatiotemporal traffic line source emissions based on massive didi online car-hailing service data

Nowadays, the massive car-hailing data has become a popular source for analyzing traffic operation and road congestion status, which unfortunately has seldom been extended to capture detailed on-road traffic emissions. This study aims to investigate the relationship between road traffic emissions and the related built environment factors, as well as land uses. The Computer Program to Calculate Emissions from Road Transport (COPERT) model from European Environment Agency (EEA) was introduced to estimate the 24-h NOx emission pattern of road segments with the parameters extracted from Didi massive trajectory data. Then, the temporal Fuzzy C-Means (FCM) Clustering was used to classify road segments based on the 24-h emission rates, while Geographical Detector and MORAN’s I were introduced to verify the impact of built environment on line source emissions and the similarity of emissions generated from the nearby road segments. As a result, the spatial autoregressive moving average (SARMA) regression model was incorporated to assess the impact of selected built environment factors on the road segment emission rate based on the probabilistic results from FCM. It was found that short road length, being close to city center, high density of bus stations, more ramps nearby and high proportion of residential or commercial land would substantially increase the emission rate. Finally, the 24-h atmospheric NO₂ concentrations were obtained from the environmental monitor stations, to calculate the time variational trend by comparing with the line source traffic emissions, which to some extent explains the contribution of on-road traffic to the overall atmospheric pollution. Result of this study could guide urban planning, so as to avoid transportation related built environment attributes which may contribute to serious atmospheric environment pollutions.     

Analysis of real driving gaseous emissions from light-duty diesel vehicles

Increasingly strict emissions standards are providing a major impetus to vehicle manufactures for developing advanced powertrain and after-treatment systems that can significantly reduce real driving emissions. The knowledge of the gaseous emissions from diesel engines under steady-state operation and under transient operation provides substantial information to analyze real driving emissions of diesel vehicles. While there are noteworthy advances in the assessment of road vehicle emissions from real driving and laboratory measurements, detailed information on real driving gaseous emissions are required in order to predict effectively the real-time gaseous emissions from a diesel vehicle under realistic driving conditions. In this work, experiments were performed to characterize the behavior of NOx, unburned HC, CO, and CO₂ emitted from light-duty diesel vehicles that comply with Euro 6 emissions standards. The driving route fully reflected various real-world driving conditions such as urban, rural, and highway. The real-time emission measurements were conducted with a Portable Emissions Measurement System (PEMS) including a Global Positioning System (GPS). To investigate the gaseous emission characteristics, authors determined the road load coefficients of vehicle specific power (VSP) and regression coefficient between fuel use rate and VSP. Furthermore, this work revealed the correlation between the rates of average fuel use and each gaseous emission.     

Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

Comparison of particle mass and number emissions from a diesel transit bus across temporal and spatial scales

This study analyzes particle number and mass emission rates measured from the exhaust of a 2002 diesel transit bus in real-world driving conditions. The dynamics of the particle number and mass emission rates are examined at resolved temporal and spatial scales across an urban arterial, a rural arterial and a divided freeway. Time-based particle number and mass emission rates were highest on the freeway, but the distance-based particle emission rates of emission/km at “hot-spots” for exposure assessment for selected 50-m road segments occurred at intersections when the bus accelerated from a stop or traveled up high grades. Comparisons of particle mass and number emission rates between idling and acceleration indicate that unless the bus is extending idling for several minutes, public exposure to bus particle emissions near bus stops can be mainly attributed to accelerations. Generally, particle number and mass emissions rates are highly correlated both temporally and spatially. Some deviations occur because particle mass emissions are highly elevated during sustained fueling events such as traveling on high grades and during sustained accelerations, while particle number emissions are more sensitive to fuel and engine speed fluctuations.     

Evaluating effects of traffic and vehicle characteristics on vehicular emissions near traffic intersections

Urban air quality is generally poor at traffic intersections due to variations in vehicles’ speeds as they approach and leave. This paper examines the effect of traffic, vehicle and road characteristics on vehicular emissions with a view to understand a link between emissions and the most likely influencing and measurable characteristics. It demonstrates the relationships of traffic, vehicle and intersection characteristics with vehicular exhaust emissions and reviews the traffic flow and emission models. Most studies have found that vehicular exhaust emissions near traffic intersections are largely dependent on fleet speed, deceleration speed, queuing time in idle mode with a red signal time, acceleration speed, queue length, traffic-flow rate and ambient conditions. The vehicular composition also affects emissions. These parameters can be quantified and incorporated into the emission models. There is no validated methodology to quantify some non-measurable parameters such as driving behaviour, pedestrian activity, and road conditions     

Network-wide traffic and environmental impacts of acceleration and deceleration among Eco-Driving Vehicles in different road configurations

Eco-Driving, a driver behaviour-based method, has featured in a number of national policy documents as part of CO₂ emission reduction or climate change strategies. This investigation comprises a detailed assessment of acceleration and deceleration in Eco-Driving Vehicles at different penetration levels in the vehicle fleet, under varying traffic composition and volume. The impacts of Eco-Driving on network-wide traffic and environmental performance at a number of speed-restricted road networks (30?km/h) is quantified using microsimulation. The results show that increasing levels of Eco-Driving in certain road networks result in significant environmental and traffic congestion detriments at the road network level in the presence of heavy traffic. Increases in CO₂ emissions of up to 18% were found. However, with the addition of vehicle-to-vehicle or vehicle-to-infrastructure communication technology which facilitates dynamic driving control on speed and acceleration/deceleration in vehicles, improvements in CO₂ emissions and traffic congestion are possible using Eco-Driving.     

Towards a real-time microscopic emissions model

This article presents a new approach to microscopic road traffic exhaust emission modelling. The model described uses data from the SCOOT demand-responsive traffic control system implemented in over 170 cities across the world. Estimates of vehicle speed and classification are made using data from inductive detector loops located on every SCOOT link. This data feeds into a microscopic traffic model to enable enhanced modelling of the driving modes of vehicles (acceleration, deceleration, idling and cruising). Estimates of carbon monoxide emissions are made by applying emission factors from an extensive literature review. A critical appraisal of the development and validation of the model is given before the model is applied to a study of the impact of high emitting vehicles. The article concludes with a discussion of the requirements for the future development and benefits of the application of such a model.     

Development of the World-wide harmonized Light duty Test Cycle (WLTC) and a possible pathway for its introduction in the European legislation

This paper presents the World-wide harmonized Light duty Test Cycle (WLTC), developed under the Working Party on Pollution and Energy (GRPE) and sponsored by the European Union (with Switzerland) and Japan. India, Korea and USA have also actively contributed. The objective was to design the harmonized driving cycle from “real world” driving data in different regions around the world, combined with suitable weighting factors. To this aim, driving data and traffic statistics of light duty vehicles use were collected and analyzed as basic elements to develop the harmonized cycle. The regional driving data and weighting factors were then combined in order to develop a unified database representing the worldwide light duty vehicle driving behavior. From the unified database, short trips were selected and combined to develop a driving cycle as representative as possible of the unified database. Approximately 765,000 km of data were collected, covering a wide range of vehicle categories, road types and driving conditions. The resulting WLTC is an ensemble of three driving cycles adapted to three vehicle categories with different power-to-mass ratio (PMR). It has been designed as a harmonized cycle for the certification of light duty vehicles around the world and, together with the new harmonized test procedures (WLTP), will serve to check the compliance of vehicle pollutant emissions with respect to the applicable emissions limits and to establish the reference vehicle fuel consumption and CO₂ performance.     

Impact of horizontal geometric design of two-lane rural roads on vehicle co2 emissions

In 2014, highway vehicles accounted for 72.8% of all Greenhouse Gases emissions from transportation in Europe. In the United States (US), emissions follow a similar trend. Although many initiatives try to mitigate emissions by focusing on traffic operations, little is known about the relationship between emissions and road design. It is feasible that some designs may increase average flow speed and reduce accelerations, consequently minimizing emissions.This study aims to evaluate the impact of road horizontal alignment on CO₂ emissions produced by passenger cars using a new methodology based on naturalistic data collection. Individual continuous speed profiles were collected from actual drivers along eleven two-lane rural road sections that were divided into 29 homogeneous road segments. The CO₂ emission rate for each homogeneous road segment was estimated as the average of CO₂ emission rates of all vehicles driving, estimated by applying the VT-Micro model.The analysis concluded that CO₂ emission rates increase with the Curvature Change Rate. Smooth road segments normally allowed drivers to reach higher speeds and maintain them with fewer accelerations. Additionally, smother segments required less time to cover the same distance, so emissions per length were lower. It was also observed that low mean speeds produce high CO₂ emission rates and they increase even more on roads with high speed dispersions.Based on this data, several regression models were calibrated for different vehicle types to estimate CO₂ emissions on a specific road segment. These results could be used to incorporate sustainability principles to highway geometric design.     

Real world vehicle emissions: Their correlation with driving parameters

Vehicular population in developing countries is expected to proliferate in the coming decade, centred on Tier II and Tier III cities rather than large metropolis. WLTP is being introduced as a global instrument for emission regulation to reduce gap between standard test procedures and actual road conditions. This work aims at quantifying and discernment of the gap between WLTC and real-world conditions in an urban city in a developing country on the basis of driving cycle parameters and simulated emissions for gasoline fuelled light passenger cars. Real world driving patterns were recorded on different routes and varying traffic conditions using car-chasing technique integrated with GPS monitoring and speed sensors. Real-world driving patterns and ambient conditions were used to simulate emissions using International Vehicle Emissions model for average rate (g/km) and Comprehensive Modal Emissions Model for instantaneous emission (g/s) analysis. Cycle parameters were mathematically calculated to compare WLTC and road trips. The analyses revealed a large gap between WLTC and road conditions. CO emissions were predicted to be 155% higher than WLTC and HC and NOx emissions were estimated to be 63% and 64% higher respectively. These gaps were correlated to different driving cycle parameters. It was observed that road driving occurs at lower average speeds with higher frequency and magnitudes of accelerations. The positive kinetic energy required by road cycles, was 100% higher than WLTC and the Relative Positive Acceleration (RPA) demanded by road cycles, was found to be 60% higher in real-world driving patterns and thereby contribute to higher emissions.     

Definition of wind blowers for vehicles testing at chassis-dyno facilities using a CFD approach

The need to increase measurement accuracy of fuel consumption and pollutant emissions in vehicles is forcing the market to develop chassis-dyno test cells that reproduce on-road conditions realistically.Air-cooling is key to vehicle performance. It is therefore critical that the design of a test cell guarantees realistic cooling of all vehicle components, as important errors in fuel consumption and emissions measurements may otherwise arise. In a test-room, a blower placed in front of the vehicle supplies the cooling air. While there are some guidelines in the literature for the selection of fans required for emissions measurements for standard driving cycles, the information for designing the air supply system for specific tests in other areas is scarce.New Real Driving Emissions (RDE) legislation will force manufacturers to perform on-road measurements of pollutants. This represents a significant challenge due to the variability of conditions coming from non-controlled parameters. In order to optimize vehicles, different tests are performed in cells equipped with a chassis-dyno where the on-road flow field around the vehicle is reproduced as closely as possible.This work provides some guidelines for the definition of the airflow supply system of chassis-dyno facilities for vehicle optimization tests, based on a CFD analysis of the flow characteristics around the vehicle. By comparison with the solution obtained for a vehicle in real road driving conditions, the exit section of the blower and the distance between the blower exit and the car that best reproduce realistic on-road flow conditions in a test room are determined.     

Instantaneous emissions models set in GIS for the TRANSIMS outputs

A novel methodology that provides more detailed estimates of vehicular polluting emissions is offered, in order to contribute to the improvement and the precision of emission inventories of vehicle sources through the consideration of instantaneous speed changes or acceleration instead of average vehicular speeds. This paper presents the construction and application of an instantaneous emissions model designated hereunder as “Transims’s Snapshots-Based Emissions”, which is set on a Geographic Information System that incorporates instantaneous fuel consumption factors and fuel-based emission factors to attain highest resolution of both, spatial and temporal distribution of vehicular polluting emissions based on traffic simulation through cellular automata with TRANSIMS. This work was applied to the road network of the Mexico City Metropolitan Area as case study. The development of this powerful tool led to obtaining 86,400 maps of the spatial and temporal distribution of vehicular emissions per vehicle circulating on the road network, including the following pollutants: carbon monoxide and carbon dioxide, nitrogen oxides, total hydrocarbons, sulfur oxides, polycyclic aromatic hydrocarbons, black carbon, particles PM₁₀ and PM_2.5. The said maps allowed identification with highest level of detail, of the emissions and Hot-spots of fuel consumption. Also, the model permitted to obtain the emissions’ longitudinal profiles of a given vehicle along its route. This study shows that the integration method of the polynomial regression models represents an opportunity for each city to develop more easily and openly its own regional emissions models without requiring deeper programming knowledge.     

The vehicle emissions and performance monitoring system: analysis of tailpipe emissions and vehicle performance

This paper describes tailpipe emission results generated by the Vehicle Performance and Emissions Monitoring system (VPEMS). VPEMS integrates on‐board emissions and vehicle/driver performance measurements with positioning and communications technologies, to transmit a coherent spatio‐temporally referenced dataset to a central base station in near real time. These results focus on relationships between tailpipe emissions of CO, CO₂, NO_x and speed and acceleration. Emissions produced by different driving modes are also presented. Results are generally as one would expect, showing variation between vehicle speed, vehicle acceleration and emissions. Data is based upon a test run in central London on urban streets with speeds not exceeding about 65 km/h. The results presented demonstrate the capabilities of the system. Various issues remain with regard to validation of the data and expansion of the system capability to obtain additional vehicle performance data.     

Characteristics of gaseous and particulate pollutants exhaust from logistics transportation vehicle on real-world conditions

On-road vehicle tests of three heavy duty diesel trucks were conducted by a portable emission measurement system (PEMS) in Chengdu, China. SEMTECH-ECOSTAR provided by Sensors Inc. was employed to detect gaseous emissions and MI2, an emissions measuring instrument powered by the Pegasor Particulate Sensor (PPS) was used to detect particulate emissions during the tests. The impacts of speed, acceleration and engine load on emissions were analyzed. The average nitrogen oxides (NOx) emission factors of the heavy duty diesel truck (HDDT), medium-duty diesel truck (MDDT), light duty diesel truck (LDDT) were 7.29, 5.29 and 5.53 g/km. The particulate emission factors were 0.60, 0.30 and 0.14 g/km respectively, higher than the similar reported in the previous studies. Both gaseous and particulate emission exhibit significant correlations with the change in vehicle speed, acceleration and power demand. The highest emission was generally in high VSPs and higher loads. High engine load caused by aggressive driving was the main factor of high emissions for the vehicles on real-world conditions.     

Assessing the importance of transportation activity data for urban emission inventories

The aim of this research is the implementation of a GPS-based modelling approach for improving the characterization of vehicle speed spatial variation within urban areas, and a comparison of the resulting emissions with a widely used approach to emission inventory compiling. The ultimate goal of this study is to evaluate and understand the importance of activity data for improving the road transport emission inventory in urban areas. For this purpose, three numerical tools, namely, (i) the microsimulation traffic model (VISSIM); (ii) the mesoscopic emissions model (TREM); and (iii) the air quality model (URBAIR), were linked and applied to a medium-sized European city (Aveiro, Portugal). As an alternative, traffic emissions based on a widely used approach are calculated by assuming a vehicle speed value according to driving mode. The detailed GPS-based modelling approach results in lower total road traffic emissions for the urban area (7.9, 5.4, 4.6 and 3.2% of the total PM10, NO_x, CO and VOC daily emissions, respectively). Moreover, an important variation of emissions was observed for all pollutants when analysing the magnitude of the 5th and 95th percentile emission values for the entire urban area, ranging from −15 to 49% for CO, −14 to 31% for VOC, −19 to 46% for NO_x and −22 to 52% for PM10. The proposed GPS-based approach reveals the benefits of addressing the spatial and temporal variability of the vehicle speed within urban areas in comparison with vehicle speed data aggregated by a driving mode, demonstrating its usefulness in quantifying and reducing the uncertainty of road transport inventories.     

Independent driving pattern factors and their influence on fuel-use and exhaust emission factors

This study is aimed at finding independent measures to describe the dimensions of urban driving patterns and to investigate which properties have main effect on emissions and fuel-use. 62 driving pattern parameters were calculated for each of 19 230 driving patterns collected in real traffic. These included traditional driving pattern parameters of speed and acceleration and new parameters of engine speed and gear-changing behaviour. By using factorial analysis the initial 62 parameters were reduced to 16 independent driving pattern factors. Fuel-use and emission factors were estimated for a subset of 5217 cases using two different mechanistic instantaneous emission models. Regression analysis on the relation between driving pattern factors and fuel-use and emission factors showed that nine of the driving pattern factors had considerable environmental effects. Four of these are associated with different aspects of power demand and acceleration, three describe aspects of gear-changing behaviour and two factors describe the effect of certain speed intervals.     

Accelerating the transformation to a low carbon passenger transport system: The role of car purchase taxes,feebates, road taxes and scrappage incentives in the UK

The transition to a low carbon transport world requires a host of demand and supply policies to be developed and deployed. Pricing and taxation of vehicle ownership plays a major role, as it affects purchasing behavior, overall ownership and use of vehicles. There is a lack in robust assessments of the life cycle energy and environmental effects of a number of key car pricing and taxation instruments, including graded purchase taxes, vehicle excise duties and vehicle scrappage incentives. This paper aims to fill this gap by exploring which type of vehicle taxation accelerates fuel, technology and purchasing behavioral transitions the fastest with (i) most tailpipe and life cycle greenhouse gas emissions savings, (ii) potential revenue neutrality for the Treasury and (iii) no adverse effects on car ownership and use.The UK Transport Carbon Model was developed further and used to assess long term scenarios of low carbon fiscal policies and their effects on transport demand, vehicle stock evolution, life cycle greenhouse gas emissions in the UK. The modeling results suggest that policy choice, design and timing can play crucial roles in meeting multiple policy goals. Both CO₂ grading and tightening of CO₂ limits over time are crucial in achieving the transition to low carbon mobility. Of the policy scenarios investigated here the more ambitious and complex car purchase tax and feebate policies are most effective in accelerating low carbon technology uptake, reducing life cycle greenhouse gas emissions and, if designed carefully, can avoid overburdening consumers with ever more taxation whilst ensuring revenue neutrality. Highly graduated road taxes (or VED) can also be successful in reducing emissions; but while they can provide handy revenue streams to governments that could be recycled in accompanying low carbon measures they are likely to face opposition by the driving population and car lobby groups. Scrappage schemes are found to save little carbon and may even increase emissions on a life cycle basis.The main policy implication of this work is that in order to reduce both direct and indirect greenhouse gas emissions from transport governments should focus on designing incentive schemes with strong up-front price signals that reward ‘low carbon’ and penalize ‘high carbon’. Policy instruments should also be subject to early scrutiny of the longer term impacts on government revenue and pay attention to the need for flanking policies to boost these revenues and maintain the marginal cost of driving.     

A velocity and payload dependent emission model for heavy-duty road freight transportation

The paper develops a forecasting model of emissions from traffic flows embracing the dynamics of driving behavior due to variations in payload. To measure of emissions at the level of individual vehicles under varying payloads a portable emission measurement system is used. This paper reports on a model based on data at the level of individual vehicles for a representative road trajectory. The model aggregates the data to the level of a homogeneous flow dependent of velocity and specific power, which is dependent on payload weight. We find a lean specification for the model that provides emission factors for CO₂, NO_x, HC, CO, and NO₂. The results indicate that, in comparison with earlier models, NO_x emissions in particular tend to be underestimated.