Electric vehicles’ energy consumption measurement and estimation

Use of electric vehicles (EVs) has been viewed by many as a way to significantly reduce oil dependence, operate vehicles more efficiently, and reduce carbon emissions. Due to the potential benefits of EVs, the federal and local governments have allocated considerable funding and taken a number of legislative and regulatory steps to promote EV deployment and adoption. With this momentum, it is not difficult to see that in the near future EVs could gain a significant market penetration, particularly in densely populated urban areas with systemic air quality problems. We will soon face one of the biggest challenges: how to improve efficiency for EV transportation system? This research takes the first step in tackling this challenge by addressing a fundamental issue, i.e. how to measure and estimate EVs’ energy consumption. In detail, this paper first presents a system which can collect in-use EV data and vehicle driving data. This system then has been installed in an EV conversion vehicle built in this research as a test vehicle. Approximately 5 months of EV data have been collected and these data have been used to analyze both EV performance and driver behaviors. The analysis shows that the EV is more efficient when driving on in-city routes than driving on freeway routes. Further investigation of this particular EV driver’s route choice behavior indicates that the EV user tries to balance the trade-off between travel time and energy consumption. Although more data are needed in order to generalize this finding, this observation could be important and might bring changes to the traffic assignment for future transportation system with a significant share of EVs. Additionally, this research analyzes the relationships among the EV’s power, the vehicle’s velocity, acceleration, and the roadway grade. Based on the analysis results, this paper further proposes an analytical EV power estimation model. The evaluation results using the test vehicle show that the proposed model can successfully estimate EV’s instantaneous power and trip energy consumption. Future research will focus on applying the proposed EV power estimation model to improve EVs’ energy efficiency.     

A network wide simulation strategy of alternative fuel vehicles

This paper presents an integrated simulator “CUIntegration” to evaluate routing strategies based on energy and/or traffic measures of effectiveness for any Alternative Fuel Vehicles (AFVs). The CUIntegration can integrate vehicle models of conventional vehicles as well as AFVs developed with MATLAB-Simulink, and a roadway network model developed with traffic microscopic simulation software VISSIM. The architecture of this simulator is discussed in this paper along with a case study in which the simulator was utilized for evaluating a routing strategy for Plug-in Hybrid Electric Vehicles (PHEVs) and Electric Vehicles (EVs). The authors developed a route optimization algorithm to guide an AFV based on that AFV driver’s choice, which included; finding a route with minimum (1) travel time, (2) energy consumption or (3) a combination of both. The Application Programming Interface (API) was developed using Visual Basic to simulate the vehicle models/algorithms developed in MATLAB and direct vehicles in a roadway network model developed in VISSIM accordingly. The case study included a section of Interstate 83 in Baltimore, Maryland, which was modeled, calibrated and validated. The authors considered a worst-case scenario with an incident on the main route blocking all lanes for 30 min. The PHEVs and EVs were represented by integrating the MATLAB-Simulink vehicle models with the traffic simulator. The CUIntegration successfully combined vehicle models with a roadway traffic network model to support a routing strategy for PHEVs and EVs. Simulation experiments with CUIntegration revealed that routing of PHEVs resulted in cost savings of about 29% when optimized for the energy consumption, and for the same optimization objective, routing of EVs resulted in about 64% savings.     

Statistical modeling of Electric Vehicle electricity consumption in the Victorian EV Trial,Australia

The market share of Electric Vehicles (EVs), an attractive alternative to conventional vehicles, is expected to exceed 30% of all vehicles by 2033 in Australia. Although the expected EV uptake may place greater burdens on electricity networks, the potential impacts contributed by different EV user categories and vehicle models to peak loads at different times during the day are not well understood. This paper addresses the issue through statistical analysis of the charge events in the Victorian EV Trial in Australia as well as modeling the charging behaviors according to participant categories and vehicle models. The analysis was performed on 4933 charge events that were recorded by both private and public Electric Vehicle Supply Equipment. In total, these events consumed over 33 MW h of energy over 12,170 h by the 178 trial participants, out of which about 70% were household participants while the others were fleet participants. Based on a range of EV uptake scenarios and modeled charging behaviors from the trial, the power demand in the summer of 2032/33 was estimated for all of Victoria. The results of the simulations show that the broad scale uptake of EVs produces a relatively small increase in overall power demand (estimated to be between 5.72% and 9.79% in 2032/33).     

Simulation of electric vehicle driver behaviour in road transport and electric power networks

The integration of electric vehicles (EVs) will affect both electricity and transport systems and research is needed on finding possible ways to make a smooth transition to the electrification of the road transport. To fully understand the EV integration consequences, the behaviour of the EV drivers and its impact on these two systems should be studied. This paper describes an integrated simulation-based approach, modelling the EV and its interactions in both road transport and electric power systems. The main components of both systems have been considered, and the EV driver behaviour was modelled using a multi-agent simulation platform. Considering a fleet of 1000 EV agents, two behavioural profiles were studied (Unaware/Aware) to model EV driver behaviour. The two behavioural profiles represent the EV driver in different stages of EV adoption starting with Unaware EV drivers when the public acceptance of EVs is limited, and developing to Aware EV drivers as the electrification of road transport is promoted in an overall context. The EV agents were modelled to follow a realistic activity-based trip pattern, and the impact of EV driver behaviour was simulated on a road transport and electricity grid. It was found that the EV agents’ behaviour has direct and indirect impact on both the road transport network and the electricity grid, affecting the traffic of the roads, the stress of the distribution network and the utilization of the charging infrastructure.     

A new offline optimization approach for designing a fuel cell hybrid bus

In this study a hydrogen powered fuel cell hybrid bus is optimized in terms of the powertrain components and in terms of the energy management strategy. Firstly the vehicle is optimized aiming to minimize the cost of its powertrain components, in an official driving cycle. The optimization variables in powertrain component design are different models and sizes of fuel cells, of electric motors and controllers, and batteries. After the component design, an energy management strategy (EMS) optimization is performed in the official driving cycle and in two real measured driving cycles, aiming to minimize the fuel consumption. The EMS optimization is based on the control of the battery’s state-of-charge. The real driving cycles are representative of bus driving in urban routes within Lisbon and Oporto Portuguese cities. A real-coded genetic algorithm is developed to perform the optimization, and linked with the vehicle simulation software ADVISOR. The trade-off between cost increase and fuel consumption reduction is discussed in the lifetime of the designed bus and compared to a conventional diesel bus. Although the cost of the optimized hybrid powertrain (62,230 €) achieves 9 times the cost of a conventional diesel bus, the improved efficiency of such powertrain achieved 36% and 34% of lower energy consumption for the real driving cycles, OportoDC and LisbonDC, which can originate savings of around 0.43 €/km and 0.37 €/km respectively. The optimization methodology presented in this work, aside being an offline method, demonstrated great improvements in performance and energy consumption in real driving cycles, and can be a great advantage in the design of a hybrid vehicle.     

How driver behaviour and parking alignment affects inductive charging systems for electric vehicles

Inductive charging, a form of wireless charging, uses an electromagnetic field to transfer energy between two objects. This emerging technology offers an alternative solution to users having to physically plug in their electric vehicle (EV) to charge. Whilst manufacturers claim inductive charging technology is market ready, the efficiency of transfer of electrical energy is highly reliant on the accurate alignment of the coils involved. Therefore understanding the issue of parking misalignment and driver behaviour is an important human factors question, and the focus of this paper. Two studies were conducted, one a retrospective analysis of 100 pre-parked vehicles, the second a dynamic study where 10 participants parked an EV aiming to align with a charging pad with no bay markings as guidance. Results from both studies suggest that drivers are more accurate at parking laterally than in the longitudinal direction, with a mean lateral distance from the centre of the bay being 12.12 and 9.57 cm (retrospective and dynamic studies respectively) compared to longitudinally 23.73 and 73.48 cm. With current inductive charging systems having typical tolerances of approximately ±10 cm from their centre point, this study has shown that only 5% of vehicles in both studies would be aligned sufficiently accurately to allow efficient transfer of electrical energy through induction.     

Comparative analysis of the energy consumption and CO2 emissions of 40 electric,plug-in hybrid electric,hybrid electric and internal combustion engine vehicles

This paper analyses the results of the Royal Automobile Clubhallo’s 2011 RAC Future Car Challenge, an annual motoring challenge in which participants seek to consume the least energy possible while driving a 92 km route from Brighton to London in the UK. The results reveal that the vehicle’s power train type has the largest impact on energy consumption and emissions. The traction ratio, defined as the fraction of time spent on the accelerator in relation to the driving time, and the amount of regenerative braking have a significant effect on the individual energy consumption of vehicles. In contrast, the average speed does not have a great effect on a vehicles’ energy consumption in the range 25–70 km/h.     

Electric vehicles’ energy consumption estimation with real driving condition data

The use of electric vehicles (EVs) is viewed as an attractive option to reduce CO₂ emissions and fuel consumption resulted from transport sector, but the popularization of EVs has been hindered by the cruising range limitation and the charging process inconvenience. Energy consumption characteristics analysis is the important foundation to study charging infrastructures locating, eco-driving behavior and energy saving route planning, which are helpful to extend EVs’ cruising range. From a physical and statistical view, this paper aims to develop a systematic energy consumption estimation approach suitable for EV actual driving cycles. First, by employing the real second-by-second driving condition data collected on typical urban travel routes, the energy consumption characteristics analysis is carried out specific to the microscopic driving parameters (instantaneous speed and acceleration) and battery state of charge (SOC). Then, based on comprehensive consideration of the mechanical dynamics characteristics and electric machine system of the EVs, a set of energy consumption rate estimation models are established under different operation modes from a statistical perspective. Finally, the performance of proposed model is fully evaluated by comparing with a conventional energy consumption estimation method. The results show that the proposed modeling approach represents a significant accuracy improvement in the estimation of real-world energy consumption. Specifically, the model precision increases by 25.25% in decelerating mode compared to the conventional model, while slight improvement in accelerating and cruising mode with desirable goodness of fit.     

Implementation and test of a hybrid storage system on an electric urban bus

Customer acceptance of Battery Electric Vehicles (BEVs) depends strongly on the performance of the Energy Storage System (ESS). Energy density, power density and lifetime of ESSs are three key parameters to be optimized in a BEV. For this purpose the use of a hybrid energy source on board of electric vehicles has been proposed and analyzed in literature. However, most of the previous studies have been limited to simulation or to test bench experiments of the ESS. This paper focuses on the implementation and use of the association of high energy NiCd battery and high power supercapacitors on board of a 3.5 t urban bus. An uncomplicated and efficient energy management strategy has been implemented and tested. The behavior of the vehicle has been investigated by experiment on a roller test bench for two different driving cycles, highlighting the effects of the hybridization: reduction of losses within the battery with consequent expected lifetime extension, improved dynamic of the vehicle and a possible driving range extension.     

Big data driven dynamic driving cycle development for busses in urban public transportation

Field-relevant reference driving cycles, equivalent to real-life operation, are a prerequisite for the consistent development and testing of vehicles, their components, and control algorithms. Furthermore they are the basis for certification and type testing. However, a static cycle can easily be detected during vehicle testing, so that optimized control parameters could be used to obtain improved emission results under test conditions. In this paper, a novel method is described and applied to generate a dynamic driving cycle that statistically matches the real-life operation of a vehicle. The analysis is performed based on an extensive field data set obtained during an automated measurement campaign of public busses for more than a full year with 27,365 h of operation and 315,583 km driven in the city of Hamburg (Germany). The data collected is statistically compared to the static reference cycles New European Driving Cycle (NEDC) and Worldwide harmonized Light Vehicles Test Procedure (WLTP). Two micro trip models with increasing complexity are described and fit to the data set. All models are quantitatively compared to the measured data set applying a Quality of Fit (QoF) indicator. Based on the highest consistency to field data, a non-deterministic driving cycle generator is developed and its output is statistically compared to the original measurement. In contrast to the existing reference cycles, the dynamic output of the non-deterministic driving cycle generator presented in this paper is statistically proven to be consistent with real-life operation of public busses in the urban environment of Hamburg.     

Wireless charging in California: Range,recharge, and vehicle electrification

This research evaluated the potential for wireless dynamic charging (charging while moving) to address range and recharge issues of modern electric vehicles by considering travel to regional destinations in California. A 200-mile electric vehicle with a real range of 160 miles plus 40 miles reserve was assumed to be used by consumers in concert with static and dynamic charging as a strict substitute for gasoline vehicle travel. Different combinations of wireless charging power (20–120 kW) and vehicle range (100–300 miles) were evaluated. One of the results highlighted in the research indicated that travel between popular destinations could be accomplished with a 200-mile EV and a 40 kW dynamic wireless charging system at a cost of about $2.5 billion. System cost for a 200-mile EV could be reduced to less than $1 billion if wireless vehicle charging power levels were increased to 100 kW or greater. For vehicles consuming 138 kWh of dynamic energy per year on a 40 kW dynamic system, the capital cost of $2.5 billion plus yearly energy costs could be recouped over a 20-year period at an average cost to each vehicle owner of $512 per year at a volume of 300,000 vehicles or $168 per year at a volume of 1,000,000 vehicles. Cost comparisons of dynamic charging, increased battery capacity, and gasoline refueling were presented. Dynamic charging, coupled with strategic wayside static charging, was shown to be more cost effective to the consumer over a 10-year period than gasoline refueling at $2.50 or $4.00 per gallon. Notably, even at very low battery prices of $100 per kWh, the research showed that dynamic charging can be a more cost effective approach to extending range than increasing battery capacity.     

Evaluating the energy performance of a SUV hybrid electric vehicle

This paper analyzes the energetic performance of the hybrid Lexus RX 400h, through on-board measurements. Several speed profiles were analyzed, for three driving types, successive stop and go cycles, three speed profiles, crossing an electronic toll collection booth, and a roundabout. In stop and go situations the internal combustion engine did not work (the torque needed to impulse the vehicle in the stop and go situations was only supported by the electric engines), as well as in the situations of constant low speeds (50 or 60 km h^?1). The auxiliary support given by the electric engines in the accelerations, as well as the importance of the energy regeneration system on the batteries’ load recovery is also demonstrated. When compared with similar conventional vehicles, the Lexus RX 400h has lower combined energy consumption between 1.2% and 60%.     

Electric vehicle parking in European and American context: Economic,energy and environmental analysis

The transportation sector faces increasing challenges related to energy consumption and local and global emissions profiles. Thus, alternative vehicle technologies and energy pathways are being considered in order to overturn this trend and electric mobility is considered one adequate possibility towards a more sustainable transportation sector.In this sense, this research work consisted on the development of a methodology to assess the economic feasibility of deploying EV charging stations (Park-EV) by quantifying the tradeoff between economic and energy/environmental impacts for EV parking spaces deployment. This methodology was applied to 4 different cities (Lisbon, Madrid, Minneapolis and Manhattan), by evaluating the influence of parking premium, infrastructure cost and occupancy rates on the investment Net Present Value (NPV). The main findings are that the maximization of the premium and the minimization of the equipment cost lead to higher NPV results. The NPV break-even for the cities considered is more “easily” reached for higher parking prices, namely in the case of Manhattan with the higher parking price profile. In terms of evaluating occupancy rates of the EV parking spaces, shifting from a low usage (LU) to a high usage (HU) scenario represented a reduction in the premium to obtain a NPV = 0 of approximately 14% for a 2500 € equipment cost, and, in the case of a zero equipment cost (e.g. financed by the city), a NPV = 0 was obtained with approximately a 2% reduction in the parking premium. Moreover, due to the use of electric mobility instead of the average conventional technologies, Well-to-Wheel (WTW) gains for Lisbon, Madrid, Minneapolis and Manhattan were estimated in 58%, 53%, 52% and 75% for energy consumption and 66%, 75%, 62% and 86% for CO₂ emissions, respectively.This research confirms that the success of deploying an EV charging stations infrastructure will be highly dependent on the price the user will have to pay, on the cost of the infrastructure deployed and on the adhesion of the EV users to this kind of infrastructure. These variables are not independent and, consequently, the coordination of public policies and private interest must be promoted in order to reach an optimal solution that does not result in prohibitive costs for the users.     

An empirical assessment of the feasibility of battery electric vehicles for day-to-day driving

Driven by sustainability objectives, Australia like many nations in the developed world, is considering the option of battery electric vehicles (BEVs) as an alternative to conventional internal combustion engine vehicles (ICEVs). In addition to issues of capital and running costs, crucial questions remain over the specifications of such vehicles, particularly the required driving range, recharge time, re-charging infrastructure, performance, and other attributes that will be of importance to consumers. With this in mind, this paper assesses (hypothetically) the extent to which current car travel needs could be met by BEVs for a sample of motorists in Sydney assuming a home-based charging set-up, which is likely to be the primary option for early adopters of the technology. The approach uses five weeks of driving data recorded by GPS technology and builds up home-home tours to assess the distances between (in effect) charging possibilities. An energy consumption model based on characteristics of the vehicle, and the speeds recorded by the GPS is adapted to determine the charge used, while a battery recharge function is used to determine charging times based on the current battery level. Among the most pertinent findings are that over the five weeks, (i) BEVs with a range as low as 60 km and a simple home-charge set-up would be able to accommodate well over 90% of day-to-day driving, (ii) however the incidence of tours requiring out-of-home charging increases markedly for vehicles below 24 kWh (170 km range), (iii) recharge time in itself has little impact on the feasibility of BEVs because vehicles spend the majority of their time parked and (iv) effective range can be dramatically impacted by both how a vehicle is driven and use of electrical auxiliaries, and (v) while unsuitable for long, high-speed journeys without some external re-charging options, BEVs appear particularly suited for the majority of day-to-day city driving in big cities where average journey speeds of 34 km/h are close to optimal in terms of maximising vehicle range. The paper has implications for both policy-makers and auto manufacturers in breaking down some of the (perceived) barriers to greater uptake of BEVs in the future.     

Electric vehicles in multi-vehicle households

The suitability of an electric vehicle of a given range to serve in place of a given conventional vehicle is not limited by the daily travel over distances within that that range, but rather by the occasional inconvenience of finding alternative transport for longer trips. While the frequency of this inconvenience can be computed from usage data, the willingness of individual users to accept that replacement depends on details of available transportation alternatives and their willingness to use them. The latter can be difficult to assess. Fortunately, 65% of US households have access to the most convenient alternative possible: a second car. In this paper we describe an analysis of prospective EV acceptance and travel electrification in two-car households in the Puget Sound region. We find that EVs with 60 miles of useful range could be acceptable (i.e. incur inconvenience no more than three days each year) to nearly 90% of two-car households and electrify nearly 55% of travel in those households (32% of all travel). This compares to 120 miles range required to achieve the same fraction of electrified travel via one-for-one replacement of individual vehicles. Even though only one third of personal vehicles in the US may be replaced in this paradigm, the ‘EV as a second-car’ concept is attractive in that a significant fraction of travel can be electrified by vehicles with modest electric range and virtually no dependence on public charging infrastructure.     

Effects of driving style on the fuel consumption of city buses under different road conditions and vehicle masses

The variance in fuel consumption caused by driving style (DS) difference exceeds 10% and reaches a maximum of 20% under different road conditions, even for experienced bus drivers. To study the influence of DS on fuel consumption, a method for summarizing DS characteristic parameters on the basis of vehicle-engine combined model is proposed. With this method, the author proposes 26 DS characteristic parameters related to fuel consumption in the accelerating, normal running, and decelerating processes of vehicles. The influence of DS characteristic parameters on fuel consumption under different road conditions and vehicle masses is quantitatively analyzed on the basis of real driving data over 100,000 km. Analysis results show that the influence of DS characteristic parameters on fuel consumption changes with road condition and vehicle mass, with road condition serving a more important function. However, the DS characteristics in the accelerating process of vehicles are decisive for fuel consumption under different conditions. This study also calculates the minimum sample size necessary for analyzing the effect of DS characteristics on fuel consumption. The statistical analysis based on the real driving data over 2500 km can determine the influence of DS on fuel consumption under a given power-train configuration and road condition. The analysis results can be employed to evaluate the fuel consumption of drivers, as well as to guide the design of Driver Advisory System for Eco-driving directly.     

Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

A control theoretic formulation of green driving strategies based on inter-vehicle communications

Various green driving strategies have been proposed to smooth traffic flow and lower pollutant emissions and fuel consumption in stop-and-go traffic. In this paper, we present a control theoretic formulation of distributed, cooperative green driving strategies based on inter-vehicle communications (IVCs). The control variable is the advisory speed limit, which is designed to smooth a following vehicle’s speed profile without changing its average speed. We theoretically analyze the performance of a constant independent and three simple cooperative green driving strategies and present three rules for effective and robust strategies. We then develop a distributed cooperative green driving strategy, in which the advisory speed limit is first independently calculated by each individual vehicle and then averaged among green driving vehicles through IVC. By simulations with Newell’s car-following model and the Comprehensive Modal Emissions Model (CMEM), we demonstrate that such a strategy is effective and robust independently as well as cooperatively for different market penetration rates of IVC-equipped vehicles and communication delays. In particular, even when 5% of the vehicles implement the green driving strategy and the IVC communication delay is 60 s, the fuel consumption can be reduced by up to 15%. Finally we discuss some future extensions.     

Influence of driving patterns on vehicle emissions: A case study for Latin American cities

On-board real-time emission experiments were conducted on 78 light-duty vehicles in Bogota. Direct emissions of carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x) and hydrocarbons (HC) were measured. The relationship between such emissions and vehicle specific power (VSP) was established. The experimental matrix included both gasoline-powered and retrofit dual fuel (gasoline–natural gas) vehicles. The results confirm that VSP is an appropriate metric to obtain correlations between driving patterns and air pollutant emissions. Ninety-five percent of the time vehicles in Bogota operate in a VSP between −15.2 and 17.7 kW ton⁻¹, and 50% of the time they operate between −2.9 and 1.2 kW ton⁻¹, representing low engine-load and near-idling conditions, respectively. When engines are subjected to higher loads, pollutant emissions increase significantly. This demonstrates the relevance of reviewing smog check programs and command-and-control measures in Latin America, which are widely based on static (i.e., idling) emissions testing. The effect of different driving patterns on the city’s emissions inventory was determined using VSP and numerical simulations. For example, improving vehicle flow and reducing sudden and frequent accelerations could curb annual emissions in Bogota by up to 12% for CO₂, 13% for CO and HC, and 24% for NO_x. This also represents possible fuel consumption savings of between 35 and 85 million gallons per year and total potential economic benefits of up to 1400 million dollars per year.     

Optimal recharging strategies for electric vehicle fleets with duration constraints

Electrical vehicles (EVs) have become a popular green transportation means recently because they have lower energy consumption costs and produce less pollution. The success of EVs relies on technologies to extend their driving range, which can be achieved by the good deployment of EV recharging stations. This paper considers a special EV network composed of fixed routes for an EV fleet, where each EV moves along its own cyclic tour of depots. By setting up a recharging station on a depot, an EV can recharge its battery for no longer than a pre-specified duration constraint. We seek an optimal deployment of recharging stations and an optimal recharging schedule for each EV such that all EVs can continue their tours in the planning horizon with minimum total costs. To solve this difficult location problem, we first propose a mixed integer program (MIP) formulation and then derive four new valid inequalities to shorten the solution time. Eight MIP models, which were created by adding different combinations of the four valid inequalities to the basic model, have been implemented to test their individual effectiveness and synergy over twelve randomly generated EV networks. Valuable managerial insights into the usage of valid inequalities and the relations between the battery capacity and the total costs, number of recharging facilities to be installed, and running time are analyzed.