柴油机在高原地区燃用混合燃料的试验研究

在高原地区对1台4100QB—2柴油机燃用生物柴油与柴油不同掺混比的混合燃料进行了台架试验。分析了混合燃料的物性,根据其物性和掺混比计算出当量燃油消耗率。对比分析了柴油机燃用混合燃料的有效热效率、机械效率和负荷特性。试验结果表明,在高原地区,柴油中加入体积比为10%~30%的生物柴油,柴油机的经济性有明显改善。     

采用燃烧器+氧化催化器的柴油机微粒捕集器复合再生控制策略的研究

设计了一种车载全流式燃烧器,从增压柴油机的涡轮增压器取出新鲜空气,从回油管路取油供给燃烧;将该装置安装在排气管尾端使捕集器进行再生.在燃烧器和捕集器之间增加氧化催化器,实现了在发动机所有稳态工况下捕集器的复合再生.在排气背压的再生控制策略基础上,根据经验公式对背压值进行温度修正,将三维背压MAP简化为二维,提出"恒温定时"的复合再生控制策略,分析了控制策略在不同工况区域的运用,给出了再生过程分析实例.对既定的控制策略进行了实车试验,结果表明微粒排放达到了国Ⅳ标准.     

Instantaneous 2-D visualization of spray combustion and flame luminosity of GTL and GTL-biodiesel fuel blend under quiescent ambient conditions

An experimental study has been performed on spray combustion and two-dimensional soot concentration in diesel (ULSD), GTL and GTL-biodiesel fuel jets under high-pressure, high-temperature quiescent conditions. Instantaneous images of the fuel jets were obtained with a high-speed camera. It was confirmed that by blending GTL with 20% rapeseed biodiesel, certain fuel properties such as kinematic viscosity, density, surface tension, volatility, lower heating value and others may be designed and improved to be more like those of conventional diesel fuel but with considerable decrease in the amount of sulfur, PAH, cold filter plugging point, etc. The results showed that the spray tip penetration increased and the spray cone angle decreased when 20% biodiesel fuel was added to GTL fuel. Autoignition of the GTL-biodiesel blend occurred slightly earlier than that of diesel fuel. Experiments under high-pressure, high-temperature conditions showed that higher injection pressure induced a lower soot formation rate. The integrated flame luminosity, which serves as an indicator of soot concentration in the fuel jet, was slightly higher for the GTL-biodiesel blend than for pure GTL fuel due to the slightly higher sulfur content of pure biodiesel fuel.     

重型柴油机燃用不同柴油替代燃料的性能研究

对乖型柴油机燃用纯柴油、体积混合比例为1:9的天然气合成油(GTL柴油)与柴油混合燃料(G10)、体积混合比例为1:9的生物柴油与柴油混合燃料(BD10)、纯GTL柴油(G100)及纯牛物柴油(BD100)5种燃料的动力性、经济性及燃烧特性进行了研究.结果表明,BD10、G10与纯柴油有相似的燃烧特性,额定转速F G100的缸内工作压力增大,BD100的缸内工作压力显著降低;G10油耗较之BD10降低2.43%,功率较之BD10平均高2.78%;与燃用纯柴油的油耗相比,G100平均降低2.62%,BD100平均高出13%;除NOx排放外,生物柴油在降低CO、HC、PM的排放上均有所改善.     

Comprehensive experimental study on the effect of biodiesel/diesel blended fuel on common-rail di diesel engine technology

This research work aims to study the aspects of using biodiesel or FAME as a component blended in diesel fuel for common-rail DI engine technology. The specific engine experiments were designed for LD commercial engine [Toyota 2KD-FTV] to understand engine combustion process, engine performance and thermal efficiency when applying FAME blended fuel. In addition, the exhaust emission in HD diesel engine [HINO J08E] was evaluated by standard HD engine emission ESC and ELR test cycles. Furthermore, the severe 400-hour of HD engine durability tests for determining the limitation on using FAME blended fuel, have been conducted with B0, B10, B20 and B50. The result shows that using of FAME blended fuel in the HD common-rail DI engine, can be applied with some guidelines experimentally discovered by this research such as filter plugging that may occur when the content of biodiesel is up to 20 % or higher, and the critical fuel injector surface polishing wear, can be observed from B50 sample. In general, the higher biodiesel content will contribute to lower power output as well, thus too high biodiesel content will cause low engine power output.     

Experimental study of the physical and chemical characteristics of biodiesel blended fuel using ultrasonic energy irradiation

The purpose of this study is to understand the physical and chemical characteristics of biodiesel blended fuel reformed by ultrasonic energy irradiation. To do this, a mixture of commercial diesel fuel and biodiesel was compared and analyzed according to whether or not ultrasonic energy irradiation was performed and the duration of irradiation. The results of the experiments indicate that when ultrasonic energy irradiation was performed on biodiesel blended fuel, its viscosity decreased by 3–7%. In the case of BD20, when ultrasonic energy irradiation was performed, its Sauter mean diameter (SMD) dropped by 12% on average. As the irradiation duration increased, the volume ratio of olefins increased up to a maximum of 2.7%, and the higher heating value increased to a maximum of 5.8%. On the contrary, the ratio of aromatics decreased by a maximum of 2.7%, and BI decreased by a maximum of 7%.     

F-T柴油与正丁醇混合燃料的燃烧和排放特性研究

F-T柴油具有十六烷值高、几乎不含硫和芳香烃的特点,正丁醇是能量密度较高的可再生的生物质燃料。在增压中冷4缸柴油机上对比研究了0号柴油、F-T柴油和F-T柴油-正丁醇混合燃料的燃烧、排放特性。结果表明:与柴油相比,掺混丁醇后缸内压力峰值、压力升高率降低;燃用F-T柴油-正丁醇混合燃料可同时降低炭烟和NO_x排放,随着正丁醇掺混比例的提高炭烟排放显著降低,F-T柴油掺混20%正丁醇的炭烟排放降幅高达67.8%,NO_x排放降幅达20.9%。     

柴油机掺烧生物柴油NO_x和Soot排放控制研究

对柴油机燃用生物柴油-0号柴油混合燃料的NO_x和Soot排放特性进行了仿真研究。在柴油机参数不作任何改变的情况下燃用体积分数分别为10%,20%,30%,40%和50%的生物柴油混合燃料,与原机的NO_x和Soot排放特性进行对比。研究表明:随着混合燃料中生物柴油体积分数的增加,柴油机Soot排放降低,NO_x排放增大。EGR的引入使柴油机NO_x排放降低,同时也使Soot排放增加。在1 800r/min中低负荷工况下,大比例生物柴油-0号柴油混合燃料应用于柴油机时,可通过调节EGR率使得柴油机NO_x和Soot排放都控制到与原机相当。     

利用柴油机尾气后处理技术实现欧Ⅳ排放标准的试验研究

以某4缸增压直喷柴油机为样机,利用专业试验台架,在优化喷油提前角和EGR阀开度的前提下,联合利用氧化催化器(DOC)及微粒氧化催化转化器(POC)技术对柴油机尾气排放进行了试验研究,并总结了DOC和POC技术对柴油机排放的影响规律.试验结果表明,通过优化喷油提前角及EGR阀开度,并且选择正确的DOC与POC的布置形式,...     

柴油机燃用麻疯树油甲酯的氮氧化物排放特性

研究了柴油机燃用麻疯树油甲酯的NOx排放特性。以1台轻型车用直喷式柴油机为试验样机,分别燃用6种不同生物柴油掺混比例的混合燃油,研究总的NOx排放以及NO,NO2,N2O等NOx主要组分的排放特性。结果表明,燃用各种混合燃油的NOx排放曲线形态较为接近,低负荷时差异较小,随负荷增加,排放差异增大。NOx排放以NO和NO2为主,NO排放随着负荷上升而增加,NO在总NOx排放中始终占有最高比例。NO2排放也占有相当比例,在低负荷时较高,随着负荷增大浓度降低,大负荷高温不利于NO2的生成。N2O排放量极低,在中低负荷时有一定生成量,高负荷N2O排放几乎为0,缸内稀燃低温有利于N2O排放的生成。在同一稳定工况下,随生物柴油混合比的提高,NOx,NO,NO2比排放量呈线性增加,N2O比排放量呈线性降低。发动机燃烧生物柴油后,NOx及其组分NO,NO2和N2O的排放量发生改变,而各自的排放变化规律并未发生变化。     

Morphological Change and Number-Size Distributions of Particulate Matter (PM) from a Diesel Generator Operated with Wood Pyrolysis Oil-Butanol Blended Fuel

This report details our experimental study investigating particulate matter (PM) emissions from a diesel generator fueled with wood pyrolysis oil (WPO)–butanol blended fuel for electricity generation. Particle number-size distributions and PM mass concentrations from diesel, n-butanol, and WPO-butanol blended fuels were investigated via aerosol measurements using a fast mobility particle sizer and an aerosol monitor with three generator outputs (0, 3.3, and 6.6 kWe). For the n-butanol and WPO-blended fuels, the total number concentrations of exhaust particles were higher than that of conventional diesel combustion; however, the PM mass was observed to be nearly zero for all the engine operating conditions due to the higher number concentration in the nuclei mode. The morphology of the exhaust particles was investigated by analyzing transmission electron microscopy (TEM) micrographs. The morphology of the particles was drastically changed according to the test fuels and engine loads. Two types of particles were observed, including soot and coke shaped particles. These results were directly related to the immaturity of incipient soot particles due to the different physical properties and chemical compositions of the fuels.     

分子筛型SCR对车用柴油机排放改善的试验研究

商用车柴油机多采用DOC+SCR的后处理系统来满足国Ⅳ、国Ⅴ排放标准的要求,而不同类型SCR的催化特性对最终污染物排放影响也不同。试验获取了一支铜基分子筛型SCR,基于1台2.8L柴油机和一支钒基SCR,运行了车用柴油机稳态循环(ESC)和瞬态排放循环(ETC),研究并分析了其对柴油机污染物的减排特性。结果表明,相较于钒基SCR,运行ETC循环时分子筛型SCR对发动机NOx和PM排放的减排效率分别提升19%和33%;分子筛型SCR对NOx的低温转化效率更高,且由于对排气流量不敏感,在高空速工况下其转化效率显著高于钒基SCR;分子筛型SCR对颗粒物个数的减排效率弱于钒基SCR,达7%以上,容易将大质量颗粒物分解为小质量颗粒物;两种SCR均对CO和HC具有一定的减排效果,减排率可达20%左右。     

纳米燃油添加剂对柴油机颗粒物排放特性的影响

在186FA柴油机上对质量分数为50mg/kg和100mg/kg的CeO2或Co3O4纳米颗粒-柴油混合燃料进行颗粒物排放特性台架试验,采用扫描电镜和热重分析仪对采集到的颗粒物样品进行微观结构形貌及热重特性分析。结果表明:纳米CeO2和Co3O4颗粒均可改善柴油机颗粒物排放,与0号柴油相比,混合燃料颗粒物比排放量下降16.4%~35.9%;混合燃料颗粒物排放的粒径分布仍呈单峰分布的特点,峰值均在0.56~1.0μm区间内,微观形态下的粒径和孔隙率明显变小,团聚程度提高;混合燃料燃烧过程中颗粒物发生氧化反应的起燃温度、失重率峰值温度及燃尽温度均有所降低,最大失重率明显增加。     

二甲醚／柴油混合燃料在压燃式发动机上的应用

为探索二甲醚/柴油混合燃料作为柴油机替代燃料的应用性能,对D20二甲醚/柴油混合燃料的喷雾特性进行了试验研究;同时,开展了直喷式柴油机燃用二甲醚/柴油混合燃料动力性能、经济性能及排放性能研究。结果表明:在同样的环境背压下,D20混合燃料的油束与柴油相比较,贯穿度有所缩短,喷雾锥角有所增大;柴油机燃用二甲醚/柴油混合燃料时,通过适当调整循环油量,发动机的动力性可以超过原柴油机,最低当量比油耗下降4.5%,烟度指标下降70%以上,NOx排放降低30%~50%;二甲醚/柴油混合燃料是一种能实现高比功率、低排放的石油替代燃料。     

柴油机燃用甲醇——生物柴油混合燃料的性能与排放研究

在186FA柴油机上,进行了燃用柴油、生物柴油和甲醇--生物柴油混合燃料的性能试验,分析了生物柴油掺烧甲醇对柴油机性能的影响规律.试验结果表明:与燃用生物柴油相比,生物柴油掺烧5%和10%(质量比)的甲醇时,柴油机的标定功率分别降低7.4%和17.8%,标定工况时能量消耗率增加5.7%和15.0%,CO排放升高40.0...     

电控高压共轨柴油机燃用生物柴油-柴油混合燃料的燃烧特性

针对1台6缸增压中冷电控高压共轨柴油机,在不改变原柴油机结构和喷油参数的条件下,研究了生物柴油的掺混比例对发动机燃烧特性的影响。结果表明:小负荷时发动机有预喷射,随着生物柴油掺混比的增大,生物柴油-柴油混合燃料的滞燃期缩短、缸内最高燃烧压力下降,预喷阶段压力升高率峰值和瞬时燃烧放热率峰值减小,且对应的相位提前;主喷阶段压力升高率峰值和瞬时燃烧放热率峰值增大,且对应的相位后移。随着负荷的增大,发动机喷油策略改为单次喷射,随着生物柴油掺混比的增大,缸内最高燃烧压力下降,燃烧持续期缩短,压力升高率峰值略有增大,瞬时燃烧放热率峰值逐渐减小且对应的相位前移。两种不同负荷条件下,随着生物柴油掺混比的增大,混合燃料的指示热效率逐渐下降。     

Experimental investigation of B20 combustion and emissions under various intake conditions for low-temperature combustion

Recently, biodiesel has emerged as an alternative fuel for achieving low-temperature combustion (LTC). Several articles in the literature have showed that oxygenated biofuels, including biodiesel, can improve combustion stability under high exhaust gas recirculation (EGR) operation, which is considered to be necessary for the removal of nitric oxides (NOx). The objective of this study was to investigate the performance and emissions of 20% biodiesel blended diesel fuel (B20) at various intake pressures and oxygen concentration levels to characterize the fuel for LTC application. The experimental investigation of B20 was carried out using a single-cylinder engine (SCE) at 1400 rpm and 50% load condition. A set of critical flow orifices with synthetic EGR was employed to simulate various intake pressures and EGR levels. The behavior of the B20 was first characterized under various intake conditions. The results showed that with high oxygen intake, B20 exhibited combustion and emission levels that were very similar to conventional diesel. However, B20 reduced combustion deterioration while exhibiting lower carbon monoxide (CO) and hydrocarbon (HC) emissions than diesel under low oxygen intake conditions.     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

生物柴油—柴油混合燃料喷雾液滴尺寸数目分布的理论预测

运用最大熵原理和质量守恒定律导出的喷雾液滴尺寸分布函数,建立了生物柴油—柴油混合燃料的喷雾液滴尺寸分布模型,对柴油、生物柴油—柴油混合燃料进行了模拟计算,并与试验结果进行了对比分析。结果表明,随着生物柴油掺混比的增大,燃料黏度增大,喷雾锥角变小,索特平均直径增大,计算数据与试验数据吻合很好。     

Experimental investigation and comparison of nanoparticle emission characteristics in light-duty vehicles for two different fuels

In recent years, particle number emissions rather than particulate mass emissions in automotive engines have become the subject with controversial discussions. Recent results from studies of health effects imply that it is possible that particulate mass does not properly correlate with the variety of health effects attributed to engine exhaust. The concern is now focusing on nano-sized particles emitted from I. C. engines. In this study, particulate mass and particle number concentration emitted from light-duty vehicles were investigated for a better understanding of the characteristics of the engine PM from different types of fuels, such as gasoline and diesel fuel. Engine nano-particle mass and size distributions of four test vehicles were measured by a condensation particle counter system, which is recommended by the particle measurement program in Europe (PMP), at the end of a dilution tunnel along a NEDC test mode on a chassis dynamometer. We found that particle number concentrations of diesel passenger vehicles with DPF system are lower than gasoline passenger vehicles, but PM mass has some similar values. However, in diesel vehicles with DPF system, PM mass and particle number concentrations were greatly influenced by PM regeneration. Particle emissions in light-duty vehicles emitted about 90% at the ECE15 cycle in NEDC test mode, regardless of vehicle fuel type. Particle emissions at the early cold condition of engine were highly emitted in the test mode.