Arterial traffic signal optimization: A person-based approach

This paper presents a real-time signal control system that optimizes signal settings based on minimization of person delay on arterials. The system’s underlying mixed integer linear program minimizes person delay by explicitly accounting for the passenger occupancy of autos and transit vehicles. This way it can provide signal priority to transit vehicles in an efficient way even when they travel in conflicting directions. Furthermore, it recognizes the importance of schedule adherence for reliable transit operations and accounts for it by assigning an additional weighting factor on transit delays. This introduces another criterion for resolving the issue of assigning priority to conflicting transit routes. At the same time, the system maintains auto vehicle progression by introducing the appropriate delays associated with interruptions of platoons. In addition to the fact that it utilizes readily available technologies to obtain the inputs for the optimization, the system’s feasibility in real-world settings is enhanced by its low computation time. The proposed signal control system is tested on a four-intersection segment of San Pablo Avenue arterial located in Berkeley, California. The findings show the system’s capability to outperform pretimed (i.e., fixed-time) optimal signal settings by reducing total person delay. They have also demonstrated its success in reducing bus person delay by efficiently providing priority to transit vehicles even when they travel in conflicting directions.     

Integrated optimization of bus priority operations in connected vehicle environment

Most previous works associated with transit signal priority merely focus on the optimization of signal timings, ignoring both bus speed and dwell time at bus stops. This paper presents a novel approach to optimize the holding time at bus stops, signal timings, and bus speed to provide priority to buses at isolated intersections. The objective of the proposed model is to minimize the weighted average vehicle delays of the intersection, which includes both bus delay and impact on nearby intersection traffic, ensuring that buses clear these intersections without being stopped by a red light. A set of formulations are developed to explicitly capture the interaction between bus speed, bus holding time, and transit priority signal timings. Experimental analysis is used to show that the proposed model has minimal negative impacts on general traffic and outperforms the no priority, signal priority only, and signal priority with holding control strategies (no bus speed adjustment) in terms of reducing average bus delays and stops. A sensitivity analysis further demonstrates the potential of the proposed approach to be applied to bus priority control systems in real‐time under different traffic demands, bus stop locations, and maximum speed limits. Copyright © 2016 John Wiley & Sons, Ltd.     

A real-time adaptive signal control in a connected vehicle environment

The state of the practice traffic signal control strategies mainly rely on infrastructure based vehicle detector data as the input for the control logic. The infrastructure based detectors are generally point detectors which cannot directly provide measurement of vehicle location and speed. With the advances in wireless communication technology, vehicles are able to communicate with each other and with the infrastructure in the emerging connected vehicle system. Data collected from connected vehicles provides a much more complete picture of the traffic states near an intersection and can be utilized for signal control. This paper presents a real-time adaptive signal phase allocation algorithm using connected vehicle data. The proposed algorithm optimizes the phase sequence and duration by solving a two-level optimization problem. Two objective functions are considered: minimization of total vehicle delay and minimization of queue length. Due to the low penetration rate of the connected vehicles, an algorithm that estimates the states of unequipped vehicle based on connected vehicle data is developed to construct a complete arrival table for the phase allocation algorithm. A real-world intersection is modeled in VISSIM to validate the algorithms. Results with a variety of connected vehicle market penetration rates and demand levels are compared to well-tuned fully actuated control. In general, the proposed control algorithm outperforms actuated control by reducing total delay by as much as 16.33% in a high penetration rate case and similar delay in a low penetration rate case. Different objective functions result in different behaviors of signal timing. The minimization of total vehicle delay usually generates lower total vehicle delay, while minimization of queue length serves all phases in a more balanced way.     

Using connected vehicle technology to improve the efficiency of intersections

Information from connected vehicles, such as the position and speed of individual vehicles, can be used to optimize traffic operations at an intersection. This paper proposes such an algorithm for two one-way-streets assuming that only a certain percentage of cars are equipped with this technology. The algorithm enumerates different sequences of cars discharging from the intersection to minimize the objective function. Benefits of platooning (multiple cars consecutively discharging from a queue) and signal flexibility (adaptability to demand) are also considered. The goal is to gain insights about the value (in terms of delay savings) of using connected vehicle technology for intersection control.Simulations are conducted for different total demand values and demand ratios to understand the effects of changing the minimum green time at the signal and the penetration rate of connected cars. Using autonomous vehicle control systems, the signal could rapidly change the direction of priority without relying on the reaction of drivers. However, without this technology a minimum green time is necessary. The results of the simulations show that a minimum green time increases the delay only for the low and balanced demand scenarios. Therefore, the value of using cars with autonomous vehicle control can only be seen at intersections with this kind of demand patterns, and could result in up to 7% decrease in delay. On the other hand, using information from connected vehicles to better adapt the traffic signal has proven to be indeed very valuable. Increases in the penetration rate from 0% up to 60% can significantly reduce the average delay (in low demand scenarios a decrease in delay of up to 60% can be observed). That being said, after a penetration rate of 60%, while the delays continue to decrease, the rate of reduction decreases and the marginal value of information from communication technologies diminishes. Overall, it is observed that connected vehicle technology could significantly improve the operation of traffic at signalized intersections, at least under the proposed algorithm.     

Priority for public transit in Germany

Priority for public transit includes a large variety of measures, including improvements to infrastructure and vehicles. For vehicles, the low floor concept is of particular importance. The central points of priority measures, however, are improvements of traffic control by traffic signals. Here, an improved sensitivity regarding public transit vehicles is the key to a remarkable reduction of factors causing delay. Different techniques for a traffic actuated signal control and different strategies regarding the degree of priority are applied. Thus, especially the reliability of public transit operations is increased. The priority efforts must be embedded in an integrated plan covering the whole urban or metropolitan transportation system.     

Self-organizing traffic signals using secondary extension and dynamic coordination

Actuated traffic signal control logic has many advantages because of its responsiveness to traffic demands, short cycles, effective use of capacity leading to and recovering from oversaturation, and amenability to aggressive transit priority. Its main drawback has been its inability to provide good progression along arterials. However, the traditional way of providing progression along arterials, coordinated–actuated control with a common, fixed cycle length, has many drawbacks stemming from its long cycle lengths, inflexibility in recovering from priority interruptions, and ineffective use of capacity during periods of oversaturation. This research explores a new paradigm for traffic signal control, “self-organizing signals,” based on local actuated control but with some additional rules that create coordination mechanisms. The primary new rules proposed are for secondary extensions, in which the green may be held to serve an imminently arriving platoon, and dynamic coordination, in which small groups of closely spaced signals communicate with one another to cycle synchronously with the group’s critical intersection. Simulation tests in VISSIM performed on arterial corridors in Massachusetts and Arizona show overall delay reductions of up to 14% compared to an optimized coordinated–actuated scheme where there is no transit priority, and more than 30% in scenarios with temporary oversaturation. Tests also show that with self-organizing control, transit signal priority can be more effective than with coordinated–actuated control, reducing transit delay by about 60%, or 12 to 14 s per intersection with little impact on traffic delay.     

The optimization of lane assignment and signal timing at the tandem intersection with pre‐signal

This paper presents an integrated model for optimizing lane assignment and signal timing at tandem intersection, which is introduced recently. The pre‐signal is utilized in the tandem intersection to reorganize the traffic flow; hence, the vehicles, regardless of whether left‐turns or through vehicles, can be discharged in all the lanes. However, the previous work does not consider the extra traffic disruption and the associated delay caused by the additional pre‐signal. In the paper, the extra delay aroused by the coordination is incorporated in a lane assignment and signal timing optimization model, and the problem is converted into a mixed‐integer non‐linear programming. A feasible directions method is hence introduced to solve the mixed‐integer non‐linear programming. The result of the optimization shows that the performance of the tandem intersection is improved and the average delay is minimized. The comparison between the tandem and the conventional configuration is presented, and the results verify that the former shows better performance than the latter. In addition, the optimal sequence corresponding to the turning proportion and the optimal lane assignment at the upstream approach of the pre‐signal are presented. Furthermore, if the number of lanes is equal in all arms, the paper proves that the average delay will be reduced if lane assignment is proportional to the turning proportion and the vehicles with low proportion are discharged in advance. Copyright © 2013 John Wiley & Sons, Ltd.     

Signalized intersections with variable flow rates: I analysis and simulation

One of the most common measures of signalized intersection operation is the amount of delay a vehicle incurs while passing through the intersection. Traditional models for estimating vehicle delay at intersections generally assume fixed signal timing and uniform arrival rates for vehicles approaching the intersection. One would expect that highly variable arrival rates would result in much longer delays than uniform arrival rates of the same average magnitude. Furthermore, one might expect that signal timing that is adjusted according to traffic volume would result in lower delay signal when variations in flow warrant such adjustable timing. This paper attempts to test several hypotheses concerning the effects of variable traffic arrival rates and adjusted signal timing through the use of simulation. The simulation results corroborate the hypothesis concerning the effect of varying arrival rates. As the variance of the arrival rate over time increases, the average delay per vehicle also increases. Signal timing adjustments based on traffic appear to decrease delay when flow rates vary greatly. As flow variations stabilize, the benefits of signal adjustments tend to diminish.     

A dynamic evacuation model for pedestrian–vehicle mixed-flow networks

In urban emergency evacuation, a potentially large number of evacuees may depend either on transit or other modes, or need to walk a long distance, to access their passenger cars. In the process of approaching the designated pick-up points or parking areas for evacuation, the massive number of pedestrians may cause tremendous burden to vehicles in the roadway network. Responsible agencies often need to contend with congestion incurred by massive vehicles emanating from parking garages, evacuation buses generated from bus stops, and the conflicts between evacuees and vehicles at intersections. Hence, an effective plan for such evacuation needs to concurrently address both the multi-modal traffic route assignment and the optimization of network signal controls for mixed traffic flows. This paper presents an integrated model to produce the optimal distribution of vehicle and pedestrian flows, and the responsive network signal plan for massive mixed pedestrian–vehicle flows within the evacuation zone. The proposed model features its effectiveness in accounting for multiple types of evacuation vehicles, the interdependent relations between pedestrian and vehicle flows via some conversion locations, and the inevitable conflicts between intersection turning vehicle and pedestrian flows. An illustrating example concerning an evacuation around the M&T stadium area has been presented, and the results indicate the promising properties of our proposed model, especially on reflecting the complex interactions between vehicle and pedestrian flows and the favorable use of high-occupancy vehicles for evacuation operations.     

Automated transit headway control via adaptive signal priority

This paper reports on a study that developed a next‐generation Transit Signal Priority (TSP) strategy, Adaptive TSP, that controls adaptively transit operations of high frequency routes using traffic signals, thus automating the operations control task and relieving transit agencies of this burden. The underlying algorithm is based on Reinforcement Learning (RL), an emerging Artificial Intelligence method. The developed RL agent is responsible for determining the best duration of each signal phase such that transit vehicles can recover to the scheduled headway taking into consideration practical phase length constraints. A case study was carried out by employing the microscopic traffic simulation software Paramics to simulate transit and traffic operations at one signalized intersection along the King Streetcar route in downtown Toronto. The results show that the control policy learned by the agent could effectively reduce the transit headway deviation and causes smaller disruption to cross street traffic compared with the existing unconditional transit signal priority algorithm.     

Model based urban traffic control,part II: Coordinated model predictive controllers

The present paper describes how to use coordination between neighbouring intersections in order to improve the performance of urban traffic controllers. Both the local MPC (LMPC) introduced in the companion paper (Hao et al., 2018) and the coordinated MPC (CMPC) introduced in this paper use the urban cell transmission model (UCTM) (Hao et al., 2018) in order to predict the average delay of vehicles in the upstream links of each intersection, for different scenarios of switching times of the traffic lights at that intersection. The feedback controller selects the next switching times of the traffic light corresponding to the shortest predicted average delay. While the local MPC (Hao et al., 2018) only uses local measurements of traffic in the links connected to the intersection in comparing the performance of different scenarios, the CMPC approach improves the accuracy of the performance predictions by allowing a control agent to exchange information about planned switching times with control agents at all neighbouring intersections. Compared to local MPC the offline information on average flow rates from neighbouring intersections is replaced in coordinated MPC by additional online information on when the neighbouring intersections plan to send vehicles to the intersection under control. To achieve good coordination planned switching times should not change too often, hence a cost for changing planned schedules from one decision time to the next decision time is added to the cost function. In order to improve the stability properties of CMPC a prediction of the sum of squared queue sizes is used whenever some downstream queues of an intersection become too long. Only scenarios that decrease this sum of squares of local queues are considered for possible implementation. This stabilization criterion is shown experimentally to further improve the performance of our controller. In particular it leads to a significant reduction of the queues that build up at the edges of the traffic region under control. We compare via simulation the average delay of vehicles travelling on a simple 4 by 4 Manhattan grid, for traffic lights with pre-timed control, traffic lights using the local MPC controller (Hao et al., 2018), and coordinated MPC (with and without the stabilizing condition). These simulations show that the proposed CMPC achieves a significant reduction in delay for different traffic conditions in comparison to these other strategies.     

Microscopic modeling of large‐scale pedestrian–vehicle conflicts in the city of Madinah,Saudi Arabia

This paper presents a micro‐simulation modeling framework for evaluating pedestrian–vehicle conflicts in crowded crossing areas. The framework adopts a simulation approach that models vehicles and pedestrians at the microscopic level while satisfying two sets of constraints: (1) flow constraints and (2) non‐collision constraints. Pedestrians move across two‐directional cells as opposed to one‐dimensional lanes as in the case of vehicles; therefore, extra caution is considered when modeling the shared space between vehicles and pedestrians. The framework is used to assess large‐scale pedestrian–vehicle conflicts in a highly congested ring road in the City of Madinah that carries 20 000 vehicles/hour and crossed by 140 000 pedestrians/hour after a major congregational prayer. The quantitative and visual results of the simulation exhibits serious conflicts between pedestrians and vehicles, resulting in considerable delays for pedestrians crossing the road (9 minutes average delay) and slow traffic conditions (average speed <10 km/hour). The model is then used to evaluate the following three mitigating strategies: (1) pedestrian‐only phase; (2) grade separation; and (3) pedestrian mall. A matrix of operational measures of effectiveness for network‐wide performance (e.g., average travel time, average speed) and for pedestrian‐specific performance (e.g., mean speed, mean density, mean delay, mean moving time) is used to assess the effectiveness of the proposed strategies. Copyright © 2012 John Wiley & Sons, Ltd.     

An integrated real-time traffic signal system for transit signal priority,incident detection and congestion management

This paper presents a traffic control system that can work standalone to handle various boundary conditions of the recurrent, non-recurrent congestion, transit signal priority and downstream blockage conditions to improve the overall traffic network vehicular productivity and efficiency. The control system uses field detectors’ data to determine the boundary conditions of all incoming and exit links. The developed system is interfaced with CORSIM micro-simulation for rigorous evaluations with different types of signal phase settings. The comparative performance of this control logic is quite satisfactory for some of the most frequently used phase settings in the network with a high number of junctions under highly congested conditions.     

An eco-driving system for electric vehicles with signal control under V2X environment

The benefit of eco-driving of electric vehicles (EVs) has been studied with the promising connected vehicle (i.e. V2X) technology in recent years. Whereas, it is still in doubt that how traffic signal control affects EV energy consumption. Therefore, it is necessary to explore the interactions between the traffic signal control and EV energy consumption. This research aims at studying the energy efficiency and traffic mobility of the EV system under V2X environment. An optimization model is proposed to meet both operation and energy efficiency for an EV transportation system with both connected EVs (CEVs) and non-CEVs. For CEVs, a stage-wise approximation model is implemented to provide an optimal speed control strategy. Non-CEVs obey a car-following rule suggested by the well-known Intelligent Driver Model (IDM) to achieve eco-driving. The eco-driving EV system is then integrated with signal control and a bi-objective and multi-stage optimization problem is formulated. For such a large-scale problem, a hybrid intelligent algorithm merging genetic algorithm (GA) and particle swarm optimization (PSO) is implemented. At last, a validation case is performed on an arterial with four intersections with different traffic demands. Results show that cycle-based signal control could improve both traffic mobility and energy saving of the EV system with eco-driving compared to a fixed signal timing plan. The total consumed energy decreases as the CEV penetration rate augments in general.     

Spatiotemporal intersection control in a connected and automated vehicle environment

Current research on traffic control has focused on the optimization of either traffic signals or vehicle trajectories. With the rapid development of connected and automated vehicle (CAV) technologies, vehicles equipped with dedicated short-range communications (DSRC) can communicate not only with other CAVs but also with infrastructure. Joint control of vehicle trajectories and traffic signals becomes feasible and may achieve greater benefits regarding system efficiency and environmental sustainability. Traffic control framework is expected to be extended from one dimension (either spatial or temporal) to two dimensions (spatiotemporal). This paper investigates a joint control framework for isolated intersections. The control framework is modeled as a two-stage optimization problem with signal optimization at the first stage and vehicle trajectory control at the second stage. The signal optimization is modeled as a dynamic programming (DP) problem with the objective to minimize vehicle delay. Optimal control theory is applied to the vehicle trajectory control problem with the objective to minimize fuel consumption and emissions. A simplified objective function is adopted to get analytical solutions to the optimal control problem so that the two-stage model is solved efficiently. Simulation results show that the proposed joint control framework is able to reduce both vehicle delay and emissions under a variety of demand levels compared to fixed-time and adaptive signal control when vehicle trajectories are not optimized. The reduced vehicle delay and CO₂ emissions can be as much as 24.0% and 13.8%, respectively for a simple two-phase intersection. Sensitivity analysis suggests that maximum acceleration and deceleration rates have a significant impact on the performance regarding both vehicle delay and emission reduction. Further extension to a full eight-phase intersection shows a similar pattern of delay and emission reduction by the joint control framework.     

Effect of signal coordination on traffic emission

This study investigates the effect of traffic signal coordination on emissions and compares it with their effects on operational performance measures of delay and stops. Various platoon ratios are obtained by simulating cycle lengths and offsets. Our results indicate that the impact of the cycle length on delay is more significant than those on stops and emissions for under-saturation traffic conditions. Given a fixed cycle length, increasing the platoon ratio can reduce delay, stops, and emissions, with reduction in emissions being correlated with stops than delay. The effect on emissions from the platoon arrival with respect to the onset of green or red indication is identified. With the same cycle length and platoon ratio, the early arrival situation, when the leading vehicles of a platoon encounters the red signal, can generate more emissions than are associated with late platoon arrival, when the last few vehicles in a platoon are stopped at the intersection by the onset of the red signal.     

An application of transyt for mixed car/streetcar operation

While the TRANSYT model for optimization of fixed-time traffic signals in a network of mixed transit and private vehicle traffic is well established, certain interactions between transit and nontransit vehicles are not properly modelled in TRANSYT. As a consequence, the optimal signal timing plan and network performance measures generated by TRANSYT may not be appropriate for the actual network. This paper briefly reviews a modelling procedure, adapted for use in the TRANSYT program, that goes some way toward overcoming TRANSYT's deficiencies in the representation of mixed traffic operation. The procedure is applied to a 6 kilometre corridor of mixed traffic operation in Toronto, Canada, to estimate the potential effects of incorporating streetcar operations in the optimization of fixed-time traffic signals.     

Multi-objective signal control of urban junctions – Framework and a London case study

This paper presents an approach to multi-objective signal control using fuzzy logic. The signal control uses fuzzy logic where the membership functions are optimised according to the Bellman–Zadeh principle of fuzzy decision-making. This approach is both practical for the decision-maker and efficient, as it leads directly to a Pareto-optimal solution. Signal control priorities are ultimately a political decision. Therefore the tool developed in this research allows the traffic engineer to balance the objectives easily by setting acceptability and unacceptability thresholds for each objective. Particular attention is given in the example to pedestrian delays. The membership functions of the fuzzy logic are optimised by a genetic algorithm coupled to the VISSIM microscopic traffic simulator. The concept is illustrated with a case study of the Marylebone Road–Baker Street intersection in London at which pedestrians as well as vehicle flows are high. The results prove the feasibility of the framework and show the vehicle delays for a more pedestrian friendly signal control strategy.     

A trajectory smoothing method at signalized intersection based on individualized variable speed limits with location optimization

Traffic signals on urban highways force vehicles to stop frequently and thus causes excessive travel delay, extra fuel consumption and emissions, and increased safety hazards. To address these issues, this paper proposes a trajectory smoothing method based on Individual Variable Speed Limits with Location Optimization (IVSL-LC) in coordination with pre-fixed traffic signals. This method dynamically imposes speed limits on some identified Target Controlled Vehicles (TCVs) with Vehicle to Infrastructures (V2I) communication ability at two IVSL points along an approaching lane. According to real-time traffic demand and signal timing information, the trajectories of each approaching vehicle are made to run smoothly without any full stop. Essentially, only TCVs’ trajectories need to be controlled and the other vehicles just follow TCVs with Gipps’ car-following model. The Dividing RECTangles (DIRECT) algorithm is used to optimize the locations of the IVSLs. Numerical simulation is conducted to compare the benchmark case without vehicle control, the individual advisory speed limits (IASL) and the proposed IVSL-LC. The result shows that compared with the benchmark, the IVSL-LC method can greatly increase traffic efficiency and reduce fuel consumption. Compared with IASL, IVSL-LC has better performance across all traffic demand levels, and the improvements are the most under high traffic demand. Finally, the results of compliance analysis show that the effect of IVSL-LC improves as the compliance rate increases.     

Empirical modelling of the relationship between bus and car speeds on signalised urban networks

Vehicle speed is an important attribute for analysing the utility of a transport mode. The speed relationship between multiple modes of transport is of interest to traffic planners and operators. This paper quantifies the relationship between bus speed and average car speed by integrating Bluetooth data and transit signal priority data from the urban network in Brisbane, Australia. The method proposed in this paper is the first of its kind to relate bus speed and average car speed by integrating multi-source traffic data in a corridor-based method. Three transferable regression models relating not-in-service bus, in-service bus during peak periods and in-service bus during off-peak periods with average car speed are proposed. The models are cross-validated and the interrelationships are significant.