Driver response to variable message signs: a stated preference investigation

This paper uses a Stated Preference approach to undertake a detailed assessment of the effect on drivers’ route choice of information provided by variable message signs (VMS). Although drivers’ response to VMS information will vary according to the availability of alternative routes and the extent to which they are close substitutes, our findings show that route choice can be strongly influenced by the provision of information about traffic conditions ahead. This has important implications for the use of VMS systems as part of comprehensive traffic management and control systems. The principal findings are that the impact of VMS information depends on: the content of the message, such as the cause of delay and its extent; local circumstances, such as relative journey times in normal conditions; and drivers’ characteristics, such as their age, sex and previous network knowledge. The impact of qualitative indicators, visible queues and delays were examined. It was found that not only is delay time more highly valued than normal travel time, which is to be expected, but that drivers become more sensitive to delay time as delay times increased across the range presented.     

Cognitive cost in route choice with real-time information: An exploratory analysis

Real-time traffic information is increasingly available to support route choice decisions by reducing the travel time uncertainty. However it is likely that a traveler cannot assess all available information on all alternative routes due to time constraints and limited cognitive capacity. This paper presents a model that is consistent with a general network topology and can potentially be estimated based on revealed preference data. It explicitly takes into account the information acquisition and the subsequent path choice. The decision to acquire information is assumed to be based on the cognitive cost involved in the search and the expected benefit defined as the expected increase in utility after the search. A latent class model is proposed, where the decision to search or not to search and the depth of the search are latent and only the final path choices are observed. A synthetic data set is used for the purpose of validation and ease of illustration. The data are generated from the postulated cognitive-cost model, and estimation results show that the true values of the parameters can be recovered with enough variability in the data. Two other models with simplifying assumptions of no information and full information are also estimated with the same set of data with significantly biased path choice utility parameters. Prediction results show that a smaller cognitive cost encourages information search on risky and fast routes and thus higher shares on those routes. As a result, the expected average travel time decreases and the variability increases. The no-information and full-information models are extreme cases of the more general cognitive-cost model in some cases, but not generally so, and thus the increasing ease of information acquisition does not necessarily warrant a full-information model.     

Real time queue length estimation for signalized intersections using travel times from mobile sensors

We study how to estimate real time queue lengths at signalized intersections using intersection travel times collected from mobile traffic sensors. The estimation is based on the observation that critical pattern changes of intersection travel times or delays, such as the discontinuities (i.e., sudden and dramatic increases in travel times) and non-smoothness (i.e., changes of slopes of travel times), indicate signal timing or queue length changes. By detecting these critical points in intersection travel times or delays, the real time queue length can be re-constructed. We first introduce the concept of Queue Rear No-delay Arrival Time which is related to the non-smoothness of queuing delay patterns and queue length changes. We then show how measured intersection travel times from mobile sensors can be processed to generate sample vehicle queuing delays. Under the uniform arrival assumption, the queuing delays reduce linearly within a cycle. The delay pattern can be estimated by a linear fitting method using sample queuing delays. Queue Rear No-delay Arrival Time can then be obtained from the delay pattern, and be used to estimate the maximum and minimum queue lengths of a cycle, based on which the real-time queue length curve can also be constructed. The model and algorithm are tested in a field experiment and in simulation.     

A practical method to estimate the benefits of improved road network reliability: an application to departing air passengers

This paper develops and applies a practical method to estimate the benefits of improved reliability of road networks. We present a general methodology to estimate the scheduling costs due to travel time variability for car travel. In contrast to existing practical methods, we explicitly consider the effect of travel time variability on departure time choices. We focus on situations when only mean delays are known, which is typically the case when standard transport models are used. We first show how travel time variability can be predicted from mean delays. We then estimate the scheduling costs of travellers, taking into account their optimal departure time choice given the estimated travel time variability. We illustrate the methodology for air passengers traveling by car to Amsterdam Schiphol Airport. We find that on average planned improvements in network reliability only lead to a small reduction in access costs per trip in absolute terms, mainly because most air passengers drive to the airport outside peak hours, when travel time variability tends to be low. However, in relative terms the reduction in access costs due to the improvements in network reliability is substantial. In our case we find that for every 1 Euro reduction in travel time costs, there is an additional cost reduction of 0.7 Euro due to lower travel time variability, and hence lower scheduling costs. Ignoring the benefits from improved reliability may therefore lead to a severe underestimation of the total benefits of infrastructure improvements.     

Incorporating uncertainty into short-term travel time predictions

To improve the quality of travel time information provided to motorists, there is a need to move away from point forecasts of travel time. Specifically, techniques are needed which predict the range of travel times which motorists may experience. This paper focuses on travel time prediction on motorways and evaluates three models for predicting the travel time range in real time as well as up to 1 h ahead. The first model, termed lane by lane tracing, relies on speed data from each lane to replicate the trajectories of relatively slow and relatively fast vehicles on the basis of speed differences across the lanes. The second model is based on the relationship between mean travel time (estimated using a neural network model) and driver-to-driver travel time variability. The results provide insight into the relative merits of the proposed techniques and confirm that they provide a basis for reliable travel time range prediction in the short-term prediction context (up to 1 h ahead).     

A probabilistic model for traffic at actuated control signals

Vehicle actuated controls are designed to adapt green and red times automatically, according to the actual dynamics of the arrival, departure and queuing processes. In turn, drivers experience variable delays and waiting times at these signals. However, in practice, delays and waiting times are computed at these systems with models that assume stationariety in the arrival process, and that are capable of computing simply expectation values, while no information is given on the uncertainty around this expectation. The growing interest on measures like travel time reliability, or network robustness motivates the development of models able to quantify the variability of traffic at these systems.This paper presents a new modeling approach for estimating queues and signal phase times, based on probabilistic theory. This model overcomes the limitations of existing models in that it does not assume stationary arrival rates, but it assumes any temporal distribution as input, and allows one to compute the temporal evolution of queue length and signal sequence probabilities. By doing so, one can also quantify the uncertainty in the estimation of delays and waiting times as time-dependent processes. The results of the probabilistic approach have been compared to the results of repeated microscopic simulations, showing good agreement. The smaller number of parameters and shorter computing times required in the probabilistic approach makes the model suitable for, e.g., planning and design problems, as well as model-based travel time estimation.     

Effect of providing traffic information estimated by a stochastic network equilibrium model with stochastic demand

To estimate travel times through road networks, in this study, we assume a stochastic demand and formulate a stochastic network equilibrium model whose travel times, flows, and demands are stochastic. This model enables us to examine network reliability under stochastic circumstances and to evaluate the effect of providing traffic information on travel times. For traffic information, we focus on travel time information and propose methods to evaluate the effect of providing that information. To examine the feasibility and validity of the proposed model and methods, we apply them to a simple network and the real road network of Kanazawa, Japan. The results indicate that providing ambulance drivers in Kanazawa with travel time information leads to an average reduction in travel time of approximately three minutes.     

How tube strikes affect macroscopic and link travel times in London

Abstract

The purpose of this study was to investigate the impact of the five strikes on the London Underground (metro) rail system, which occurred in 2009 and 2010, on macroscopic and road link travel times. A consequence of these strikes was an increase in road traffic flows above usual levels. This provides an opportunity to observe the operation of the road network under unusually high flows. The first objective involves the examination of strike effects on inbound (IT) and outbound traffic (OT) within central, inner and outer London. Travel time data obtained from automatic number plate recognition cameras are used within the first part of the analysis. The second more detailed objective was to investigate in spatio-temporal effects on travel times on five road links. Correlation analyses and general linear models are developed using both traffic flow and travel time data. According to the results of the study, the morning IT had approximately twice as much delay as the OT. Central London experienced the highest delays, followed by inner and outer London. As would be expected, the unique full-day strike in 2009 yielded the worst impact on the network with the highest percentage increase in total travel time (60%) occurring during the morning peak in the IT in inner London. The results from the link-level analysis showed statistical significance amongst the examined links indicating heterogeneous effects from one link to another. It was also found that travel time changes may be more effectively captured through time-of-day terms compared to hourly traffic flows.     

Modeling travel time reliability of freeways using risk assessment techniques

Travel time reliability is considered to be one of the key indicators for the performance of transport systems and is measured in various ways. This paper synthesizes both reliability concepts: traffic breakdown, the indicator of the instability of travel times, is treated as the risk, whereas travel time variability, the indicator of the uncertainty of travel times, is considered as the consequence of this risk. An analytical formula, using risk assessment technique, explicitly expresses the cost of travel time unreliability as the sum of the products of the consequences (i.e. variability) and the corresponding probabilities of breakdown. It provides a novel measure of travel time reliability and is applicable in network performance evaluations. An empirical example based on a large dataset of freeway traffic flow data from loop detectors shows that the developed travel time reliability measure is both intuitively logical and consistent.     

Accommodating risk in the valuation of expected travel time savings

Valuation of travel time savings is a critical measure in transport infrastructure appraisal, traffic modelling and network performance. It has been recognised for some time that the travel times associated with repeated trips are subject to variation, and hence there is risk embedded in the treatment of expected travel time. In the context of the expected utility framework, we use a nonlinear probability weighting function to accommodate choice made under risk. Although the empirical findings suggest small differences between the value of expected travel time savings (VETTS) in the presence and absence of risk, the mean estimate does make a noticeable difference to time benefits when applied to real projects. By incorporating nonlinear probability weighting, our model reveals that the probabilities associated with specific travel times that are shown to respondents in the choice experiment are transformed, resulting in overweighting of outcomes with low probabilities and underweighting of outcomes with high probabilities. Copyright © 2011 John Wiley & Sons, Ltd.     

Estimating link travel time functions for heterogeneous traffic flows on freeways

Oversized vehicles, such as trucks, significantly contribute to traffic delays on freeways. Heterogeneous traffic populations, that is, those consisting of multiple vehicles types, can exhibit more complicated travel behaviors in the operating speed and performance, depending on the traffic volume as well as the proportions of vehicle types. In order to estimate the component travel time functions for heterogeneous traffic flows on a freeway, this study develops a microscopic traffic‐simulation based four‐step method. A piecewise continuous function is proposed for each vehicle type and its parameters are estimated using the traffic data generated by a microscopic traffic simulation model. The illustrated experiments based on VISSIM model indicate that (i) in addition to traffic volume, traffic composition has significant influence on the travel time of vehicles and (ii) the respective estimations for travel time of heterogeneous flows could greatly improve their estimation accuracy. Copyright © 2016 John Wiley & Sons, Ltd.     

Probe vehicle based real-time traffic monitoring on urban roadways

Travel time estimation and prediction on urban arterials is an important component of Active Traffic and Demand Management Systems (ATDMS). This paper aims in using the information of GPS probes to augment less dynamic but available information describing arterial travel times. The direction followed in this paper chooses a cooperative approach in travel time estimation using static information describing arterial geometry and signal timing, semi-dynamic information of historical travel time distributions per time of day, and utilizes GPS probe information to augment and improve the latter. First, arterial travel times are classified by identifying different travel time states, then link travel time distributions are approximated using mixtures of normal distributions. If prior travel time data is available, travel time distributions can be estimated empirically. Otherwise, travel time distribution can be estimated based on signal timing and arterial geometry. Real-time GPS travel time data is then used to identify the current traffic condition based on Bayes Theorem. Moreover, these GPS data can also be used to update the parameters of the travel time distributions using a Bayesian update. The iterative update process makes the posterior distributions more and more accurate. Finally, two comprehensive case studies using the NGSIM Peachtree Street dataset, and GPS data of Washington Avenue in Minneapolis, were conducted. The first case study estimated prior travel time distributions based on signal timing and arterial geometry under different traffic conditions. Travel time data were classified and corresponding distributions were updated. In addition, results from the Bayesian update and EM algorithm were compared. The second case study first tested the methodologies based on real GPS data and showed the importance of sample size. In addition, a methodology was proposed to distinguish new traffic conditions in the second case study.     

What do commuters think travel time reliability is worth? Calculating economic value of reducing the frequency and extent of unexpected delays

The measurement of transportation system reliability has become one of the central topics of travel demand studies. A growing literature concerns the measurement of value of travel time reliability which provides a monetary cost of avoiding unpredictable travel time. The goal of this study is to measure commuters’ sensitivities to travel time reliability and their willingness to pay (WTP) to avoid unreliable routes. The preferences are elicited through a pivoted stated preference survey technique. To circumvent the issue of presenting numerical distributions and statistical terms to day-to-day commuters, we use the frequency of delay days as a means of measuring traveler’s sensitivities to travel time reliability. The advantage of using simplified measures to elicit traveler preferences for travel time reliability is that these methods simply compare days with high delay to days with usual travel time. It was found that travelers are not only averse to the amount of unexpected delay but also to the frequency of days with unexpected delays. The paper presents WTP findings for three measures: travel time, frequency embedded travel time, and travel time reliability. The ‘reliability’ increase in WTP for travel time is found to be nearly proportional to the frequency of experiencing unexpected delays. For example, the WTP for mean travel time is calculated at $6.98/h; however, reliability adds $3.27 (about 50 % of $6.98) to avoid unexpected delays ‘5 out of 10 days’. The results of the study would provide valuable inputs to cost-benefit analyses and traffic and revenue studies required for road tolling investment projects.     

Modeling stochastic perception error in the mean-excess traffic equilibrium model

In this paper, we extend the α-reliable mean-excess traffic equilibrium (METE) model of Chen and Zhou (Transportation Research Part B 44(4), 2010, 493-513) by explicitly modeling the stochastic perception errors within the travelers’ route choice decision processes. In the METE model, each traveler not only considers a travel time budget for ensuring on-time arrival at a confidence level α, but also accounts for the impact of encountering worse travel times in the (1 − α) quantile of the distribution tail. Furthermore, due to the imperfect knowledge of the travel time variability particularly in congested networks without advanced traveler information systems, the travelers’ route choice decisions are based on the perceived travel time distribution rather than the actual travel time distribution. In order to compute the perceived mean-excess travel time, an approximation method based on moment analysis is developed. It involves using the conditional moment generation function to derive the perceived link travel time, the Cornish-Fisher Asymptotic Expansion to estimate the perceived travel time budget, and the Acerbi and Tasche Approximation to estimate the perceived mean-excess travel time. The proposed stochastic mean-excess traffic equilibrium (SMETE) model is formulated as a variational inequality (VI) problem, and solved by a route-based solution algorithm with the use of the modified alternating direction method. Numerical examples are also provided to illustrate the application of the proposed SMETE model and solution method.     

Accounting for travel time variability in the optimal pricing of cars and buses

A number of studies have shown that in addition to travel time and cost as the common influences on mode, route and departure time choices, travel time variability plays an increasingly important role, especially in the presence of traffic congestion on roads and crowding on public transport. The dominant focus of modelling and implementation of optimal pricing that incorporates trip time variability has been in the context of road pricing for cars. The main objective of this paper is to introduce a non-trivial extension to the existing literature on optimal pricing in a multimodal setting, building in the role of travel time variability as a source of disutility for car and bus users. We estimate the effect of variability in travel time and bus headway on optimal prices (i.e., tolls for cars and fares for buses) and optimal bus capacity (i.e., frequencies and size) accounting for crowding on buses, under a social welfare maximisation framework. Travel time variability is included by adopting the well-known mean–variance model, using an empirical relationship between the mean and standard deviation of travel times. We illustrate our model with an application to a highly congested corridor with cars, buses and walking as travel alternatives in Sydney, Australia. There are three main findings that have immediate policy implications: (i) including travel time variability results in higher optimal car tolls and substantial increases in toll revenue, while optimal bus fares remain almost unchanged; (ii) when bus headways are variable, the inclusion of travel time variability as a source of disutility for users yields higher optimal bus frequencies; and (iii) including both travel time variability and crowding discomfort leads to higher optimal bus sizes.     

Joint optimization of tram timetables and signal timing adjustments at intersections

This paper explores at the planning level the benefits of coordinating tram movements and signal timings at controlled intersections. Although trams may have dedicated travel lanes, they mostly operate in a mixed traffic environment at intersections. To ensure tram progression, pre-set signal timings at intersections are adjusted by activating Transit Signal Priority (TSP) actions, which inevitably add delays to the auto traffic. A mixed integer program is proposed for jointly determining tram schedules for a single tram line and modifying signal timings at major controlled intersections. The objective is to minimize the weighted sum of the total tram travel time and TSP’s negative impacts on other traffic. A real-world case study of Line 5 of the Shenyang Hunnan Modern Tramway shows that by extending the dwell time or link travel time we can significantly reduce the TSP’s negative impacts on the auto traffic while only slightly increasing tram travel times.     

Investigating empirical implications of hysteresis in day-to-day travel time variability

Day-to-day travel time variability plays a significant role in travel time reliability. Nowadays, travelers not only seek to minimize their travel time on average, but also value its variation. The variation in the mean and the variance of travel time (across days, for the same departure time) has not been thoroughly investigated. A temporary decrease in capacity (e.g. congestion caused by an active bottleneck) leads to a quite significant difference in the variance of travel time for congestion onset and offset periods. This phenomenon results in hysteresis loops where the departure time periods in congestion offset exhibit a higher travel time variance than the ones in congestion onset with the same mean travel time. The aim of this paper is to identify empirical implications that yield to the hysteresis phenomenon in day-to-day travel times. First, empirical hysteresis loop observations are provided from two different freeway sites. Second, we investigate the potential link with the hysteresis observed in traffic networks on macroscopic fundamental diagram (MFD). Third, we build a piecewise linear function that models the evolution of travel time within the day. This allows us to decompose the problem into its components, e.g. start time of congestion, peak travel time, etc. These components, along with their probability distribution functions, are employed in a Monte Carlo simulation model to investigate their partial effects on the existence of hysteresis. Correlation among critical variables is the most influential factor in this phenomenon, which should be further investigated regarding traffic flow and traffic equilibrium principles.     

The impacts of connected vehicle technology on network-wide traffic operation and fuel consumption under various incident scenarios

ABSTRACT

Incidents are a major source of traffic congestion and can lead to long and unpredictable delays, deteriorating traffic operations and adverse environmental impacts. The emergence of connected vehicles and communication technologies has enabled travelers to use real-time traffic information. The ability to exchange traffic information among vehicles has tremendous potential impacts on network performance especially in the case of non-recurrent congestion. To this end, this paper utilizes a microscopic simulation model of traffic in El Paso, Texas to investigate the impacts of incidents on traffic operation and fuel consumption at different market penetration rates (MPR) of connected vehicles. Several scenarios are implemented and tested to determine the impacts of incidents on network performance in an urban area. The scenarios are defined by changing the duration of incidents and the number of lanes closed. This study also shows how communication technology affects network performance in response to congestion. The results of the study demonstrate the potential effectiveness of connected vehicle technology in improving network performance. For an incident with a duration of 900?s and MPR of 80%, total fuel consumption and total travel time decreased by approximately 20%; 26% was observed in network-wide travel time and fuel consumption at 100% MPR.     

An adaptive information fusion model to predict the short-term link travel time distribution in dynamic traffic networks

As intelligent transportation systems (ITS) approach the realm of widespread deployment, there is an increasing need to robustly capture the variability of link travel time in real-time to generate reliable predictions of real-time traffic conditions. This study proposes an adaptive information fusion model to predict the short-term link travel time distribution by iteratively combining past information on link travel time on the current day with the real-time link travel time information available at discrete time points. The past link travel time information is represented as a discrete distribution. The real-time link travel time is represented as a range, and is characterized using information quality in terms of information accuracy and time delay. A nonlinear programming formulation is used to specify the adaptive information fusion model to update the short-term link travel time distribution by focusing on information quality. The model adapts good information by weighing it higher while shielding the effects of bad information by reducing its weight. Numerical experiments suggest that the proposed model adequately represents the short-term link travel time distribution in terms of accuracy and robustness, while ensuring consistency with ambient traffic flow conditions. Further, they illustrate that the mean of a representative short-term travel time distribution is not necessarily a good tracking indicator of the actual (ground truth) time-dependent travel time on that link. Parametric sensitivity analysis illustrates that information accuracy significantly influences the model, and dominates the effects of time delay and the consistency constraint parameter. The proposed information fusion model bridges key methodological gaps in the ITS deployment context related to information fusion and the need for short-term travel time distributions.     

A multi‐class mean‐excess traffic equilibrium model with elastic demand

Recent empirical studies have revealed that travel time variability plays an important role in travelers' route choice decisions. To simultaneously account for both reliability and unreliability aspects of travel time variability, the concept of mean‐excess travel time (METT) was recently proposed as a new risk‐averse route choice criterion. In this paper, we extend the mean‐excess traffic equilibrium model to include heterogeneous risk‐aversion attitudes and elastic demand. Specifically, this model explicitly considers (1) multiple user classes with different risk‐aversions toward travel time variability when making route choice decisions under uncertainty and (2) the elasticity of travel demand as a function of METT when making travel choice decisions under uncertainty. This model is thus capable of modeling travelers' heterogeneous risk‐averse behaviors with both travel choice and route choice considerations. The proposed model is formulated as a variational inequality problem and solved via a route‐based algorithm using the modified alternating direction method. Numerical analyses are also provided to illustrate the features of the proposed model and the applicability of the solution algorithm. Copyright © 2012 John Wiley & Sons, Ltd.