Isocyanic acid and ammonia in vehicle emissions

Vehicles are considered to be an important source of ammonia (NH₃) and isocyanic acid (HNCO). HNCO and NH₃ have been shown to be toxic compounds. Moreover, NH₃ is also a precursor in the formation of atmospheric secondary aerosols. For that reason, real-time vehicular emissions from a series of Euro 5 and Euro 6 light-duty vehicles, including spark ignition (gasoline and flex-fuel), compression ignition (diesel) and a plug-in electric hybrid, were investigated at 23 and −7 °C over the new World harmonized Light-duty vehicle Test Cycle (WLTC) in the Vehicle Emission Laboratory at the European Commission Joint Research Centre Ispra, Italy. The median HNCO emissions obtained for the studied fleet over the WLTC were 1.4 mg km⁻¹ at 23 °C and 6 mg km⁻¹ at −7 °C. The fleet median NH₃ emission factors were 10 mg km⁻¹ and 21 mg km⁻¹ at 23 and −7 °C, respectively. The obtained results show that even though three-way catalyst (TWC), selective catalytic reduction (SCR), and NOx storage catalyst (NSC) are effective systems to reduce NOx vehicular emissions, they also lead to considerable emissions of the byproducts NH₃ and/or HNCO. It is also shown that diesel light-duty vehicles equipped with SCR can present NH₃ emission factors as high as gasoline light-duty vehicles at both, 23 and −7 °C over the WLTC. Therefore, with the introduction in the market of this DeNOx technology, vehicular NH₃ emissions will increase further.     

Energy use and emissions of two stroke-powered tricycles in Metro Manila

CO, CO₂, NO_x and HC emissions of two stroke-powered tricycles in Metro Manila are examined using an instantaneous emissions model. Results show that fuel consumption and HC emissions in middle class residential areas and main roads are similar but lower than levels in low income residential areas. On the average, tricycles in Metro Manila consume 24.41 km/l of fuel and produces 9.5, 9.7, 40.5 and 0.07 g/km of HC, CO, CO₂ and NO_x, respectively. They fail to satisfy HC, CO and NO_x emission limits set by reference standards in the Philippines and other Asian countries. They produce greater HC and CO emissions than gasoline fueled private cars and diesel powered public jeepneys, taxis and buses on a per passenger-km basis but significantly lower NO_x emissions. Tricycles account for 15.4% of the total HC emissions from mobile sources in the metropolis while their contributions to CO, CO₂ and NO_x are minimal.     

Exhaust emissions generated under actual operating conditions from a hybrid vehicle and an electric one fitted with a range extender

The paper describes exhaust emission tests performed on a PHEV (Plug-in Hybrid Electric Vehicle) and a BEV (Battery Electric Vehicle), in which the combustion engine was used as a range extender. The measurements of the exhaust emissions were performed for CO₂/fuel consumption, CO, THC and NO_x. The RDE measurements were performed including the engine operating parameters and emissions analysis. This analysis shows that the engines of BEVs and PHEVs operate in a different parameter range when under actual operating conditions, which directly translates into the exhaust emission values. This is particularly the case for the emission of NO_x. The investigations were carried out for two routes differentiated by the length and share of the urban and extra-urban cycles. For both routes, the emission of THC and CO were lower for the PHEV engine – HC by 69% (22 mg/km, route 1) and 6% (15 mg/km, route 2), CO by 69% (0.12 mg/km, route 1) and 80% (0.1 mg/km, route 2). For route 1, characterized by a greater share of the urban cycle, the emission of NO_x was lower by 70% (2 mg/km) for the BEV engine, and (route 2) lower by 60% (8 mg/km) for the PHEV engine. Additionally, the curves of the exhaust emissions in time for individual exhaust components have been presented that indicate that in the motorway cycle the emission of THC and CO from the BEV vehicle increases significantly up to ten times compared to urban cycle.     

Characteristics of air pollutants at near and far field regions of a national highway located at an industrial complex

This paper presents the characterization of air quality monitored at near field region (NFR) and far field region (FFR) of a national highway located at an industrial complex. The pollutants such as PM₁₀, SO₂ and NO₂ were monitored in two campaigns (11th September to 18th October 2012 and 18th January to 17th February 2013). The 24 h average PM₁₀ concentration at NFR and FFR were found to be 86.69 ± 18.56 μg/m³; 73.16 ± 16.21 μg/m³ and 89.44 ± 18.69 μg/m³; 81.91 ± 16.42 μg/m³, respectively during first and second campaign. In both the campaigns PM₁₀, SO₂ and NO₂ concentration at NFR was higher than FFR. The chemical characterization of PM₁₀ at NFR and FFR indicated the abundance of major elements such as Na (NFR = 30% and FFR = 32%), Ca (NFR = 12% and FFR = 14%) and ions namely NO₃⁻ (NFR = 71% and FFR = 68%) and NH₃⁺ (NFR = 15% and FFR = 19%). Further, at FFR, SO₄²⁻ and NO₃⁻ were found to be 18% and 35% higher than NFR indicating the conversions of SO₂ and NO₂ concentration into secondary particles. The measured SO₂ and NO₂ concentrations were 23 and 21% lower at FFR when compared to NFR confirms the secondary formation.The CALPUFF, EPA regulatory model was set up to understand the dynamics of air pollutants at the industrial complex. The predicted PM₁₀, SO₂ and NO₂ concentrations at NFR and FFR were found to be 32.31 ± 1.56 μg/m³ and 31.35 ± 1.27 μg/m³; 0.37 ± 0.21 μg/m³ and 0.06 ± 0.04 μg/m³; 12.83 ± 6.55 μg/m³ and 4.67 ± 2.77 μg/m³, respectively. The model showed moderate predictions for PM₁₀ (R² = 0.44–0.52), SO₂ (R² = 0.41–0.51) and NO₂ (R² = 0.45–0.61) concentrations.     

Characteristics of gaseous and particulate pollutants exhaust from logistics transportation vehicle on real-world conditions

On-road vehicle tests of three heavy duty diesel trucks were conducted by a portable emission measurement system (PEMS) in Chengdu, China. SEMTECH-ECOSTAR provided by Sensors Inc. was employed to detect gaseous emissions and MI2, an emissions measuring instrument powered by the Pegasor Particulate Sensor (PPS) was used to detect particulate emissions during the tests. The impacts of speed, acceleration and engine load on emissions were analyzed. The average nitrogen oxides (NOx) emission factors of the heavy duty diesel truck (HDDT), medium-duty diesel truck (MDDT), light duty diesel truck (LDDT) were 7.29, 5.29 and 5.53 g/km. The particulate emission factors were 0.60, 0.30 and 0.14 g/km respectively, higher than the similar reported in the previous studies. Both gaseous and particulate emission exhibit significant correlations with the change in vehicle speed, acceleration and power demand. The highest emission was generally in high VSPs and higher loads. High engine load caused by aggressive driving was the main factor of high emissions for the vehicles on real-world conditions.     

Effects of the 80 km/h and variable speed limits on air pollution in the metropolitan area of barcelona

In 2008 the regional government of Catalonia (Spain) reduced the maximum speed limit on several stretches of congested urban motorway in the Barcelona metropolitan area to 80 km/h, while in 2009 it introduced a variable speed system on other stretches of its metropolitan motorways. We use the differences-in-differences method, which enables a policy impact to be measured under specific conditions, to assess the impact of these policies on emissions of NO_x and PM₁₀. Empirical estimation indicate that reducing the speed limit to 80 km/h causes a 1.7–3.2% increase in NO_x and 5.3–5.9% in PM₁₀. By contrast, the variable speed policy reduced NO_x and PM₁₀ pollution by 7.7–17.1% and 14.5–17.3%. As such, a variable speed policy appears to be a more effective environmental policy than reducing the speed limit to a maximum of 80 km/h.     

How wide should be the adjacent area to an urban motorway to prevent potential health impacts from traffic emissions?

In recent years, several studies show that people who live, work or attend school near the main roadways have an increased incidence and severity of health problems that may be related with traffic emissions of air pollutants. The concentrations of near-road atmospheric pollutants vary depending on traffic patterns, environmental conditions, topography and the presence of roadside structures. In this study, the vertical and horizontal variation of nitrogen dioxide (NO₂) and benzene (C₆H₆) concentration along a major city ring motorway were analysed. The main goal of this study is to try to establish a distance from this urban motorway considered “safe” concerning the air pollutants human heath limit values and to study the influence of the different forcing factors of the near road air pollutants transport and dispersion. Statistic significant differences (p = 0.001, Kruskal–Wallis test) were observed between sub-domains for NO₂ representing different conditions of traffic emission and pollutants dispersion, but not for C₆H₆ (p = 0.335). Results also suggest significant lower concentrations recorded at 100 m away from roadway than at the roadside for all campaigns (p < 0.016 (NO₂) and p < 0.036 (C₆H₆), Mann–Whitney test). In order to have a “safe” life in homes located near motorways, the outdoor concentrations of NO₂ must not exceed 44–60.0 μg m⁻³ and C₆H₆ must not exceed 1.4–3.3 μg m⁻³. However, at 100 m away from roadway, 81.8% of NO₂ receptors exceed the annual limit value of human health protection (40 μg m⁻³) and at the roadside this value goes up to 95.5%. These findings suggest that the safe distance to an urban motorway roadside should be more at least 100 m. This distance should be further studied before being used as a reference to develop articulated urban mobility and planning policies.     

Influence of driving patterns on vehicle emissions: A case study for Latin American cities

On-board real-time emission experiments were conducted on 78 light-duty vehicles in Bogota. Direct emissions of carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x) and hydrocarbons (HC) were measured. The relationship between such emissions and vehicle specific power (VSP) was established. The experimental matrix included both gasoline-powered and retrofit dual fuel (gasoline–natural gas) vehicles. The results confirm that VSP is an appropriate metric to obtain correlations between driving patterns and air pollutant emissions. Ninety-five percent of the time vehicles in Bogota operate in a VSP between −15.2 and 17.7 kW ton⁻¹, and 50% of the time they operate between −2.9 and 1.2 kW ton⁻¹, representing low engine-load and near-idling conditions, respectively. When engines are subjected to higher loads, pollutant emissions increase significantly. This demonstrates the relevance of reviewing smog check programs and command-and-control measures in Latin America, which are widely based on static (i.e., idling) emissions testing. The effect of different driving patterns on the city’s emissions inventory was determined using VSP and numerical simulations. For example, improving vehicle flow and reducing sudden and frequent accelerations could curb annual emissions in Bogota by up to 12% for CO₂, 13% for CO and HC, and 24% for NO_x. This also represents possible fuel consumption savings of between 35 and 85 million gallons per year and total potential economic benefits of up to 1400 million dollars per year.     

Total water requirements of passenger transport modes

With a growing urban population, it is crucial to maintain and develop environmentally friendly transport modes. However, while one of the most important indicators of environmental performance is water use, very few studies have quantified the total water requirements associated with different transport modes.This study uses input-output analysis to quantify the total water requirements of different passenger-transport modes in Melbourne, Australia, including the direct and indirect water requirements of petrol cars, regional diesel trains and electric metropolitan trains.Results show that urban electric trains are the least water intensive transport mode (3.4 L/pkm) followed by regional diesel trains (5.2 L/pkm) and petrol cars (6.4 L/pkm). These intensities result in average daily per capita transport-related water use that can be greater than residential water use. Findings also show that occupancy rates greatly affect the water intensity of transport modes and that when occupied by five passengers, cars are the least water intensive transport mode. Finally, this study shows that water use associated with transport depends on a range of factors across the supply chain and that indirect requirements associated with operations, including administration, advertisement, servicing and others, can represent a significant share of the total. Reducing the total water requirements of transport modes is therefore a shared responsibility between all the actors involved and integrated action plans are needed in order to reduce water use associated with transport.     

An assessment of gasoline motorcycle emissions performance and understanding their contribution to Tehran air pollution

Motorcycles are the third most common means of transportation in the megacity of Tehran. Hence, measurements of emission factors are essential for Tehran motorcycle fleets. In this study, 60 carburetor motorcycles of various mileages and engine displacement volumes were tested in a chassis dynamometer laboratory according to cold start Euro-3 emissions certification test procedures. For almost all of the tested samples, the average carbon monoxide (CO) emission factors were about seven times higher than the limits for Euro-3 certification. No motorcycle fell within the Euro-3 certification limit on CO emissions. 125 cc engine displacement volume motorcycles, which are dominant in Tehran, have the most total unburned hydrocarbons and CO emission rates, and they have less nitrous oxides (NO_X) emission rates and fuel consumption compared to those of larger engine volume motorcycles. Calculation of fuel-based emission factors and moles of combustion products shows that about 40% of fuel consumed by 125 cc engine volume motorcycles burns to incomplete combustion products. This proportion is lower for larger engine volume motorcycles. Approximation of relative air–fuel ratio results shows very rich combustion in selected motorcycles. Using a carburetor fuel supply system, low engine compression ratio, aging, and no catalyst could be reasons for high emission rates. These reasons could possibly result in high ultrafine particles emission rates from motorcycles. Comparison of total motorcycle pollutant emissions to that of passenger cars from previous studies in Tehran shows that motorcycles contribute to pollutant much higher than their contribution to the total fleet or total travels.     

Thermodynamic,environmental and economic effects of diesel and biodiesel fuels on exhaust emissions and nano-particles of a diesel engine

In this study, diesel (JIS#2) and various biodiesel fuels (BDF20, BDF50, BDF100) are used to operate the diesel engine at 100 Nm, 200 Nm and full load; while the engine speed is 1800 rpm. The system is experimentally studied, and the energy, exergy, sustainability, thermoeconomic and exergoeconomic analyses are performed to the system. The Engine Exhaust Particle Sizer is used to measure the size distribution of engine exhaust particle emissions. Also, the data of the exhaust emissions, soot, particle numbers, fuel consumptions, etc. are measured. It is found that (i) most of the exhaust emissions (except NO_x) are directly proportional to the engine load, (ii) maximum CO₂ and NO_x emissions rates are generally determined for the BDF100 biodiesel fuel; while the minimum ones are calculated for the JIS#2 diesel fuel. On the other hand, the maximum CO and HC emissions rates are generally computed for the JIS#2 diesel fuel; while the minimum ones are found for the BDF100 biodiesel fuel, (iii) fuel consumptions from maximum to minimum are BDF100 > BDF50 > BDF20 > JIS#2 at all of the engine loads, (iv) particle concentration of the JIS#2 diesel fuel is higher than the biodiesel fuels, (v) soot concentrations of the JIS#2, BDF20 and BDF50 fuels are directly proportional to the engine load; while the BDF100 is inversely proportional, (vi) system has better energy and exergy efficiency when the engine is operated with the biodiesel fuels (vii) sustainability of the fuels are BDF100 > BDF50 > BDF20 > JIS#2, (viii) thermoeconomic and exergoeconomic parameters rates from maximum to minimum are JIS#2 > BDF20 > BDF50 > BDF100.     

Carbon emission from urban passenger transportation in Beijing

Urban passenger transport significantly contributes to global greenhouse gas emissions, especially in developing countries owing to the rapid motorization, thus making it an important target for carbon reduction. This article established a method to estimate and analyze carbon emission from urban passenger transport including cars, rail transit, taxis and buses. The scope of research was defined based on car registration area, transport types and modes, the stages of rail transit energy consumption. The data availability and gathering were fully illustrated. A city level emission model for the aforementioned four modes of passenger transport was formulated, and parameters including emission factor of electricity and fuel efficiency were tailored according to local situations such as energy structure and field survey. The results reveal that the emission from Beijing’s urban passenger transport in 2012 stood at 15 million tonnes of CO₂, of which 75.5% was from cars, whereas car trip sharing constitutes only 42.5% of the total residential trips. Bus travel, yielding 28.6 g CO₂, is the most efficient mode of transport under the current situations in terms of per passenger kilometer (PKM) emission, whereas car or taxi trips emit more than 5 times that of bus trips. Although a decrease trend appears, Beijing still has potential for further carbon reduction in passenger transport field in contrast to other cities in developed countries. Development of rail transit and further limitation on cars could assist in reducing 4.39 million tonnes CO₂ emission.     

New car preferences move away from greater size,weight and power: Impact of Dutch consumer choices on average CO2-emissions

This paper assesses the separate effects of consumer preferences and technological advances on sales-weighted average CO₂ emissions of new passenger cars in the Netherlands. Since 2008, consumer preferences have been moving away from large size, weight and power whereby car buyers were offsetting more than 50% of the potential CO₂ reduction from technological advances. From 2008 to 2011 consumer choices not only ceased to offset a large share of the technological advances, but contributed more than an additional 30% to CO₂ reductions. Had consumer preferences not decoupled from the historical upward trend, the Dutch sales-weighted average CO₂ emissions of new passenger cars would have been 139 g/km rather than the 126 grams CO₂ per km in 2011.     

On the electrification of road transportation – A review of the environmental,economic, and social performance of electric two-wheelers

Electrification is widely considered as a viable strategy for reducing the oil dependency and environmental impacts of road transportation. In pursuit of this strategy, most attention has been paid to electric cars. However, substantial, yet untapped, potentials could be realized in urban areas through the large-scale introduction of electric two-wheelers. Here, we review the environmental, economic, and social performance of electric two-wheelers, demonstrating that these are generally more energy efficient and less polluting than conventionally-powered motor vehicles. Electric two-wheelers tend to decrease exposure to pollution as their environmental impacts largely result from vehicle production and electricity generation outside of urban areas. Our analysis suggests that the price of e-bikes has been decreasing at a learning rate of 8%. Despite price differentials of 5000 ± 1800 EUR₂₀₁₂ kW h⁻¹ in Europe, e-bikes are penetrating the market because they appear to offer an apparent additional use value relative to bicycles. Mid-size and large electric two-wheelers do not offer such an additional use value compared to their conventional counterparts and constitute niche products at price differentials of 700 ± 360 EUR₂₀₁₂ kW⁻¹ and 160 ± 90 EUR₂₀₁₂ kW⁻¹, respectively. The large-scale adoption of electric two-wheelers can reduce traffic noise and road congestion but may necessitate adaptations of urban infrastructure and safety regulations. A case-specific assessment as part of an integrated urban mobility planning that accounts, e.g., for the local electricity mix, infrastructure characteristics, and mode-shift behavior, should be conducted before drawing conclusions about the sustainability impacts of electric two-wheelers.     

The impact of road grade on carbon dioxide (CO2) emission of a passenger vehicle in real-world driving

To accurately estimate real-world vehicle emission at 1 Hz the road grade for each second of data must be quantified. Failure to incorporate road grade can result in over or underestimation of a vehicle’s power output and hence cause inaccuracy in the instantaneous emission estimate. This study proposes a simple LiDAR (Light Detection And Ranging) – GIS (Geographic Information System) road grade estimation methodology, using GIS software to interpolate the elevation for each second of data from a Digital Terrain Map (DTM). On-road carbon dioxide (CO₂) emissions from a passenger car were recorded by Portable Emission Measurement System (PEMS) over 48 test laps through an urban-traffic network. The test lap was divided into 8 sections for micro-scale analysis. The PHEM instantaneous emission model (Hausberger, 2003) was employed to estimate the total CO₂ emission through each lap and section. The addition of the LiDAR-GIS road grade to the PHEM modelling improved the accuracy of the CO₂ emission predictions. The average PHEM estimate (with road grade) of the PEMS measured section total CO₂ emission (n = 288) was 93%, with 90% of the PHEM estimates between 80% and 110% of the PEMS recorded value. The research suggests that instantaneous emission modelling with LiDAR-GIS calculated road grade is a viable method for generating accurate real-world micro-scale CO₂ emission estimates. The sensitivity of the CO₂ emission predictions to road grade was also tested by lessening and exaggerating the gradient profiles, and demonstrates that assuming a flat profile could cause considerable error in real-world CO₂ emission estimation.     

The potential health,financial and environmental impacts of dieselgate in Ireland

ABSTRACT

The transportation sector is the greatest contributor to air pollution. With the booming demand for transportation, reducing the pollution has become one of the main concerns of researchers. EPA emission standards are designed to protect air quality and human health. Diesel Euro 5 NO_x has become a matter of disquiet since it has been found that NO_x emissions are significantly exceeding the standard limit. This paper presents a study to estimate the disparity in real-world NO_x emission levels resulted from all diesel Euro 5 passenger cars (PC) and light commercial vehicles (LCV) that are present in Ireland. NO_x emission levels calculated based on laboratory test results, on-road measurements and the COPERT 4 model were compared. Additionally, NO_x emission levels from the defective Volkswagen models have been calculated to quantify the effect of the Volkswagen scandal on Ireland. Impacts of excess NO_x emissions on health and cost have also been presented.     

The economy of alternative fuels when including the cost of air pollution

In this study, the costs involved in the use of petrol, diesel, natural gas, biogas, and methanol (produced from natural gas and biomass) in cars and heavy trucks are compared. The cost includes fuel cost, extra capital cost for vehicles using alternative fuels, and the environmental cost of VOC, NO_x, particulate and CO₂ emission based on actual 1996 and estimated 2015 emission factors. The costs have been calculated separately for rural, urban and city-centre traffic. A complete macroeconomic assessment of the effect of introducing alternative fuels is not, however, included in the study. The study shows that no alternative fuel can compete with petrol and diesel in rural traffic when the economic valuation of CO₂ emission is taken as current Swedish CO₂ taxes ($200/tonne C). In cities with a natural gas network, natural gas is the fuel with the lowest cost for both cars and heavy trucks, based on 1996 emission factors. Methanol from natural gas and biogas from waste products can also compete with diesel in urban traffic. With predicted improvements in technology and subsequent emission reductions, no alternative fuel can compete with petrol in any of the traffic situations studied by 2015, and only in city-centre traffic will alternative fuels be less costly than diesel in heavy vehicles. Of the biomass-based fuels studied, low-cost biogas from waste products is the most competitive one and is, already at current CO₂ taxes, the fuel with lowest cost for heavy trucks in urban traffic in areas where natural gas networks do not exist. To enable the more widespread use of biomass-based fuels, i.e. using feedstocks such as energy crops or logging residues that are available in larger amounts, the economic valuation of CO₂ emission has to be 2–2.5 times higher than current Swedish CO₂ tax level.     

Commuters’ exposure to PM2.5 and CO2 in metro carriages of Shanghai metro system

Air quality inside transportation carriages has become a public concern. A comprehensive measurement campaign was conducted to examine the commuters’ exposure to PM_2.5 (d_p ⩽ 2.5 μm) and CO₂ in Shanghai metro system under different conditions. The PM_2.5 and CO₂ concentrations inside all the measured metro lines were observed at 84 ± 42 μg/m³ and 1253.1 ± 449.1 ppm, respectively. The factors that determine the in-carriage PM_2.5 and CO₂ concentrations were quantitatively investigated. The metro in-carriage PM_2.5 concentrations were significantly affected by the ventilation systems, out-carriage PM_2.5 concentrations and the passenger numbers. The largest in-carriage PM_2.5 and CO₂ concentrations were observed at 132 μg/m³ and 1855.0 ppm inside the carriages equipped with the oldest ventilation systems. The average PM_2.5 and CO₂ concentrations increased by 24.14% and 9.93% as the metro was driven from underground to overground. The average in-carriage PM_2.5 concentrations increased by 17.19% and CO₂ concentration decreased by 16.97% as the metro was driven from urban to the suburban area. It was found that PM_2.5 concentration is proportional to the on-board passenger number at a ratio of 0.4 μg/m³·passenger. A mass-balance model was developed to estimate the in-carriage PM_2.5 concentration under different driving conditions.     

Are multi-car households better suited for battery electric vehicles? – Driving patterns and economics in Sweden and Germany

Battery electric vehicles (BEVs) could reduce CO₂ emissions from the transport sector but their limited electric driving range diminishes their utility to users. The effect of the limited driving range can be reduced in multi-car households where users could choose between a BEV and a conventional car for long-distance travel. However, to what extent the driving patterns of different cars in a multi-car household’s suit the characteristics of a BEV needs further analysis. In this paper we analyse the probability of daily driving above a fixed threshold for conventional cars in current Swedish and German car driving data. We find second cars in multi-car households to require less adaptation and to be better suited for BEV adoption compared to first cars in multi-car households as well as to cars in single-car households. Specifically, the share of second cars that could fulfil all their driving is 20 percentage points higher compared to first cars and cars from single-car households. This result is stable against variation of driving range and of the tolerated number of days requiring adaptation. Furthermore, the range needed to cover all driving needs for about 70% of the vehicles is only 220 km for second cars compared to 390 km for the average car. We can further confirm that second cars have higher market viability from a total cost of ownership perspective. Here, the second cars achieve a 10 percentage points higher market share compared to first cars, and to cars in single-car households for Swedish economic conditions, while for Germany the corresponding figure is 2 percentage points. Our results are important for understanding the market viability of current and near-future BEVs.     

Six years of CO2-based tax incentives for new passenger cars in The Netherlands: Impacts on purchasing behavior trends and CO2 effectiveness

There is growing evidence that consumers respond more effectively to upfront price signals, such as vehicle purchase taxes and feebate policies, and to tax incentives that are more salient than others, such as company car taxes graded by CO₂ emissions. This paper examines tax changes in The Netherlands, which are among the most stringent and most salient in Europe, and assesses the ex-post purchasing impacts and CO₂ effectiveness of six years of CO₂-based tax incentives for low-carbon cars in The Netherlands. Dutch tax incentives resulted in 13 g/km, or 11% lower average CO₂ emissions in 2013. The Netherlands has moved from the 12th position before the tax changes in 2007 to become Europe’s number one in terms of the lowest average new car CO₂ emissions and highest share of electric vehicles in 2013. Tax incentives for new cars sold between 2008 and 2013 have resulted in 4.6 million tons of potential lifetime CO₂ abatement at the cost of a drop in tax revenues of 30–50%. However, when corrected for the Dutch policy-induced increasing real-world fuel-economy shortfall and leakage of carbon reduction potential through vehicle export of low-carbon cars, only 3.5 million tons or 75% of the CO₂ reduction remains. CO₂-based tax incentives for company cars seem to have contributed the most to the observed turnaround in purchasing behavior towards lower CO₂-emitting passenger cars.