Analytical and simulation approaches to understand combined effects of transit signal priority and road-space priority measures

Transit signal priority (TSP) may be combined with road-space priority (RSP) measures to increase its effectiveness. Previous studies have investigated the combination of TSP and RSP measures, such as TSP with dedicated bus lanes (DBLs) and TSP with queue jump lanes (QJLs). However, in these studies, combined effects are usually not compared with separate effects of each measure. In addition, there is no comprehensive study dedicated to understanding combined effects of TSP and RSP measures. It remains unclear whether combining TSP and RSP measures creates an additive effect where the combined effect of TSP and RSP measures is equal to the sum of their separate effects. The existence of such an additive effect would suggest considerable benefits from combining TSP and RSP measures. This paper explores combined effects of TSP and RSP measures, including TSP with DBLs and TSP with QJLs. Analytical results based on time-space diagrams indicate that at an intersection level, the combined effect on bus delay savings is smaller than the additive effect if there is no nearside bus stop and the traffic condition in the base case is under-saturated or near-saturated. With a near-side bus stop, the combined effect on bus delay savings at an intersection level can be better than the additive effect (or over-additive effect), depending on dwell time, distance from the bus stop to the stop line, traffic demand, and cycle length. In addition, analytical results suggest that at an arterial level, the combined effect on bus delay savings can be the over-additive effect with suitable signal offsets. These results are confirmed by a micro-simulation case study. Combined effects on arterial and side-street traffic delays are also discussed.     

An analytical model to conduct a person-based evaluation of transit preferential treatments on signalized arterials

The complexities of urban transportation networks where multiple modes with different characteristics and needs travel in combination with constraints on space and funding make the sustainable management of these systems a challenge. In order to improve transit service, space (e.g., dedicated bus lanes) and time (e.g., transit signal priority strategies) Transit Preferential Treatments (TPT) are deployed to improve transit operations. The objective of this paper is to develop an analytical model that allows for a person-based evaluation of alternative TPTs when considered individually and in combination. In particular, the analytical model is developed to assess person delay and person discharge flow at any intersection that is part of a signalized arterial, where auto arrivals are in platoons. The performance of TPTs is evaluated using both the analytical model and through microsimulation tests on two intersections of San Pablo Avenue in Berkeley, CA. Space TPTs such as dedicated bus lanes and queue jumper lanes are beneficial in reducing bus person delay when provided in addition to the existing lanes; however, the effectiveness of time TPTs such as green extension depends on the level of auto demand in combination with signal settings. Changes in person discharge flow are not significant for any of the treatments tested with the exception of the bus lane substitution with and without green extension, which led to a significant decrease in person discharge flow. Increased bus frequency increases the effectiveness of transit signal priority in reducing total and bus person delay. The analytical model results produce ranking outcomes that are comparable with the microsimulation ones and therefore, the model may be used for a quantitative evaluation of TPTs without the need for data intensive and time consuming calibration efforts required for microsimulation models. The developed model can be used to guide infrastructure and investment decisions on where such TPTs should be implemented and under what conditions space TPTs should be combined with time TPTs to improve person mobility.     

Multi-modal traffic signal control with priority,signal actuation and coordination

Both coordinated-actuated signal control systems and signal priority control systems have been widely deployed for the last few decades. However, these two control systems are often conflicting with each due to different control objectives. This paper aims to address the conflicting issues between actuated-coordination and multi-modal priority control. Enabled by vehicle-to-infrastructure (v2i) communication in Connected Vehicle Systems, priority eligible vehicles, such as emergency vehicles, transit buses, commercial trucks, and pedestrians are able to send request for priority messages to a traffic signal controller when approaching a signalized intersection. It is likely that multiple vehicles and pedestrians will send requests such that there may be multiple active requests at the same time. A request-based mixed-integer linear program (MILP) is formulated that explicitly accommodate multiple priority requests from different modes of vehicles and pedestrians while simultaneously considering coordination and vehicle actuation. Signal coordination is achieved by integrating virtual coordination requests for priority in the formulation. A penalty is added to the objective function when the signal coordination is not fulfilled. This “soft” signal coordination allows the signal plan to adjust itself to serve multiple priority requests that may be from different modes. The priority-optimal signal timing is responsive to real-time actuations of non-priority demand by allowing phases to extend and gap out using traditional vehicle actuation logic. The proposed control method is compared with state-of-practice transit signal priority (TSP) both under the optimized signal timing plans using microscopic traffic simulation. The simulation experiments show that the proposed control model is able to reduce average bus delay, average pedestrian delay, and average passenger car delay, especially for highly congested condition with a high frequency of transit vehicle priority requests.     

Operational performance comparison of four unconventional intersection designs using micro‐simulation

Several unconventional intersection designs have been proposed as an innovative approach to mitigate congestion at heavily congested at‐grade signalized intersections. Many of these unconventional designs were shown to outperform conventional intersections in terms of the average control delay and the overall intersection capacity. Little research has been conducted to compare the performance of these unconventional intersections to each other under different volume conditions. This study evaluated and compared the operational performance of four unconventional intersection schemes: the crossover displaced left‐turn (XDL), the upstream signalized crossover (USC), the double crossover intersection (DXI) (i.e., half USC), and the median U‐turn (MUT). The micro‐simulation software vissim (PTV Planung Transport Verkehr AG, Karlsruhe, Germany) was used to model and analyze the four unconventional intersections as well as a counterpart conventional one. The results showed that the XDL intersection constantly exhibited the lowest delays at nearly all tested balanced and unbalanced volume levels. The operational performance of both the USC and the DXI was similar in most volume conditions. The MUT design, on the other hand, was unable to accommodate high approach volumes and heavy left‐turn traffic. The capacity of the XDL intersection was found to be 99% higher than that of the conventional intersection, whereas the capacity of the USC and the DXI intersections was about 50% higher than that of the conventional intersection. The results of this study can provide guidance on choosing among alternative unconventional designs according to the prevailing traffic conditions at an intersection. Copyright © 2012 John Wiley & Sons, Ltd.     

The evaluation of active bus-priority signal routes

In an attempt to provide priority facilities for high occupancy vehicles, many cities have investigated or installed active bus priority signals at selected intersections. This paper describes one such installation at the intersection of Bell Street and Oriel Road in Heidelberg, Victoria, Australia. In particular, it describes the impact of the signals on bus performance levels and on non-priority traffic performance levels. An evaluation is performed taking account of the costs of the installation, the changes in the amount of fuel consumed and the changes in the perceived, budgeted delay of people passing through the intersection. Perceived, budgeted delay is defined so as to take account of the variability of delay and the perception of small delay changes. The evaluation at this site showed that, for various reasons, it was difficult to justify the priority signals at this isolated intersection.The evaluation is then extended to the concept of a route of bus priority signal intersections. A simple model is built to simulate the performance of such a priority route and the evaluation repeated. As a result of using perceived delay as a measure of performance, it is then shown that although the priority intersections along the route may not be individually justifiable, the priority route as a whole may show considerable net benefits. These benefits will occur given that there are greater than a critical number of priority intersections on the route. This critical number will depend on the assumptions made in the priority route model.It is concluded that re-evaluation of bus priority signal intersections along the lines suggested in the paper may yield a number of viable bus priority intersections and bus priority routes which were previously considered to be non-viable.     

Multi-stage stochastic program to optimize signal timings under coordinated adaptive control

In the wake of traffic congestion at intersections, it is imperative to shorten delays in corridors with stochastic arrivals. Coordinated adaptive control can adjust green time flexibly to deal with a stochastic demand, while maintaining a minimum through-band for coordinated intersections. In this paper, a multi-stage stochastic program based on phase clearance reliability (PCR) is proposed to optimize base timing plans and green split adjustments of coordinated intersections under adaptive control. The objective is to minimize the expected intersection delay and overflow of the coordinated approach. The overflow or oversaturated effect is explicitly addressed in the delay calculation, which greatly increases the modeling complexity due to the interaction of overflow delays across cycles. The notion of PCR separates the otherwise related green time settings of consecutive cycles into a number of stages, in which the base timing plan and actual timing plan in different cycles are handled sequentially. We then develop a PCR based solution algorithm to solve the problem, and apply the model and the solution algorithm to actual intersections in Shanghai to investigate its performance as compared with Allsop’s method and Webster’s method. Preliminary results show the PCR-based method can significantly shorten delays and almost eliminates overflow for the coordinated approaches, with acceptable delay increases of the non-coordinated approaches. A comparison between the proposed coordinated adaptive logic and a coordinated actuated logic is also conducted in the case study to show the advantages and disadvantages.     

An investigation of multiplier effects generated by implementing queue jump lanes at multiple intersections

This paper investigates the combination effects of queue jump lanes (QJLs) on signalised arterials to establish if a multiplier effect exists, that is, the benefit from providing QJLs at multiple intersections is higher than the sum of benefits from providing them individually at each of those intersections. To explore the combination effects on bus delay and total person delay, a delay estimation model is developed using kinematic wave theory, kinematic equations and Monte Carlo simulation. In addition, to investigate the combination effects in offset settings optimised for bus delay or total person delay, offset optimisation models are proposed. Validation results using traffic micro‐simulation indicate the effectiveness and computational efficiency of the proposed models. Results of a modelling test bed suggest that providing QJLs at multiple intersections can create a multiplier effect on one‐directional bus delay savings with signal offsets that provide bus progression. Furthermore, optimising offsets to minimise bus delay tends to create a multiplier effect on one‐directional bus delay savings, particularly when variations in dwell times are not high. The reason for the multiplier effect may be that providing QJLs reduces variations in bus travel times, which makes signal coordination for buses perform more effectively. From a policy perspective, the existence of a multiplier effect suggests that a corridor‐wide scale implementation of QJLs has considerable merit. Copyright © 2016 John Wiley & Sons, Ltd.     

Development of a signal-head-free intersection control logic in a fully connected and autonomous vehicle environment

Establishment of effective cooperation between vehicles and transportation infrastructure improves travel reliability in urban transportation networks. Lack of collaboration, however, exacerbates congestion due mainly to frequent stops at signalized intersections. It is beneficial to develop a control logic that collects basic safety message from approaching connected and autonomous vehicles and guarantees efficient intersection operations with safe and incident free vehicle maneuvers. In this paper, a signal-head-free intersection control logic is formulated into a dynamic programming model that aims to maximize the intersection throughput. A stochastic look-ahead technique is proposed based on Monte Carlo tree search algorithm to determine the near-optimal actions (i.e., acceleration rates) over time to prevent movement conflicts. Our numerical results confirm that the proposed technique can solve the problem efficiently and addresses the consequences of existing traffic signals. The proposed approach, while completely avoids incidents at intersections, significantly reduces travel time (ranging between 59.4% and 83.7% when compared to fixed-time and fully-actuated control strategies) at intersections under various demand patterns.     

Unconventional USC intersection corridors: evaluation of potential implementation in Doha,Qatar

Unconventional intersection designs have been recently proposed as a new approach to deal with heavy left turns at signalized intersections. One of these unconventional schemes, the Upstream Signalized Crossover (USC) intersection, was shown to significantly reduce average vehicle delays; particularly when the volumes entering the intersection are relatively high. The Ministry of Public Works of Qatar is considering the implementation of the USC intersection on three signalized intersections along a major urban corridor in Doha. This paper investigates the potential improvements associated with the USC implementation. VISSIM was used to analyze the proposed USC intersections and the existing conventional intersections. Analyses were carried out for AM , Midday, and PM peak hours. The results showed that most of the travel time measurement sections experienced lower delays in the USC configuration for the three peak periods. As well, the total system delay, in hours, for the USC configuration was less than that of the conventional configuration by 19.4, 14.8, and 13.6% for the AM , Midday, and PM peaks, respectively. The average control delay for each single USC intersection was lower than its conventional counterpart by between 7.6 and 22.9%. Copyright © 2010 John Wiley & Sons, Ltd.     

Integrated optimization of bus priority operations in connected vehicle environment

Most previous works associated with transit signal priority merely focus on the optimization of signal timings, ignoring both bus speed and dwell time at bus stops. This paper presents a novel approach to optimize the holding time at bus stops, signal timings, and bus speed to provide priority to buses at isolated intersections. The objective of the proposed model is to minimize the weighted average vehicle delays of the intersection, which includes both bus delay and impact on nearby intersection traffic, ensuring that buses clear these intersections without being stopped by a red light. A set of formulations are developed to explicitly capture the interaction between bus speed, bus holding time, and transit priority signal timings. Experimental analysis is used to show that the proposed model has minimal negative impacts on general traffic and outperforms the no priority, signal priority only, and signal priority with holding control strategies (no bus speed adjustment) in terms of reducing average bus delays and stops. A sensitivity analysis further demonstrates the potential of the proposed approach to be applied to bus priority control systems in real‐time under different traffic demands, bus stop locations, and maximum speed limits. Copyright © 2016 John Wiley & Sons, Ltd.     

Bus dispatching at timed transfer transit stations using bus tracking technology

A timed transfer terminal synchronizes the arrival of incoming vehicles with the departure of outgoing vehicles so as to minimize transfer delays. Most bus timed transfer terminals follow fixed schedules, and do not utilize intelligent transportation systems for vehicle tracking and control. This paper reviews technologies that enable real-time control of timed transfer. We evaluate the benefits of tracking bus locations and executing dynamic schedule control through the simulation of a generic timed transfer terminal under a range of conditions. Based on empirical data collected by the Los Angeles County/Metropolitan Transit Agency, we found delay over segments of long-headway bus lines to be negatively correlated with lateness at the start of the segment, indicating that buses have a tendency to catch up when they fall behind schedule. The simulation analysis showed that the benefit of bus tracking is most significant when one of the buses experiences a major delay, especially when there is a small number of connecting buses.     

A continuous-flow-intersection-lite design and traffic control for oversaturated bottleneck intersections

Oversaturation has become a severe problem for urban intersections, especially the bottleneck intersections that cause queue spillover and network gridlock. Further improvement of oversaturated arterial traffic using traditional mitigation strategies, which aim to improve intersection capacity by merely adjusting signal control parameters, becomes challenging since exiting strategies may (or already) have reached their “theoretical” limits of optimum. Under such circumstance, several novel unconventional intersection designs, including the well-recognized continuous flow intersection (CFI) design, are originated to improve the capacity at bottleneck intersections. However, the requirement of installing extra sub-intersections in a CFI design would increase vehicular stops and, more critically, is unacceptable in tight urban areas with closed spaced intersections. To address these issues, this research proposes a simplified continuous flow intersection (called CFI-Lite) design that is ideal for arterials with short links. It benefits from the CFI concept to enable simultaneous move of left-turn and through traffic at bottleneck intersections, but does not need installation of sub-intersections. Instead, the upstream intersection is utilized to allocate left-turn traffic to the displaced left-turn lane. It is found that the CFI-Lite design performs superiorly to the conventional design and regular CFI design in terms of bottleneck capacity. Pareto capacity improvement for every traffic stream in an arterial system can be achieved under effortless conditions. Case study using data collected at Foothill Blvd in Los Angeles, CA, shows that the new design is beneficial in more than 90% of the 408 studied cycles. The testing also shows that the average improvements of green bandwidths for the synchronized phases are significant.     

基于VISSIM的平面交叉口交通仿真与改善研究

平面交叉口是交通系统中极易发生拥堵的地方,运用先进的仿真软件VISSIM对交叉口进行改善设计具有较强的优势。文章在分析VIS-SIM仿真软件原理的基础上,提出了平面交叉口的改善方法,并以兰州市建宁路与宝石花路交叉口为例进行了交叉口改善与仿真分析。研究结论对城市平面交叉口改善设计具有一定的借鉴意义。     

Modeling schedule recovery processes in transit operations for bus arrival time prediction

Many existing algorithms for bus arrival time prediction assume that buses travel at free‐flow speed in the absence of congestion. As a result, delay incurred at one stop would propagate to downstream stops at the same magnitude. In reality, skilled bus operators often constantly adjust their speeds to keep their bus on schedule. This paper formulates a Markov chain model for bus arrival time prediction that explicitly captures the behavior of bus operators in actively pursuing schedule recovery. The model exhibits some desirable properties in capturing the schedule recovery process. It guarantees provision of the schedule information if the probability of recovering from the current schedule deviation is sufficiently high. The proposed model can be embedded into a transit arrival time estimation model for transit information systems that use both real‐time and schedule information. It also has the potential to be used as a decision support tool to determine when dynamic or static information should be used.     

“互联网+”交通信号辅助优化机制探索

为优化城市道路交通信号控制方法,本文结合交通信号控制系统建设发展现状,分析当前各大城市交通信号控制系统普遍存在的问题,立足于互联网环境下的浮动车数据,提出基于互联网平台大数据的交通信号控制辅助优化机制。研究发现可利用互联网路口拥堵报警数据及时有效发现问题路口,利用路段拥堵指数及路口交通流参数变化趋势辅助评估配时方案的优化效果,并通过成都市应用实例证明该机制适用于当前交通控制场景需求,可有效辅助交通信号优化工作,是传统交通模式向真正智能交通模式过渡的阶梯。     

Adaptive control algorithm to provide bus priority with a pre-signal

In urban areas, where road space is limited, it is important to provide efficient public and private transportation systems to maximize person throughput, for example from a signalized intersection. To this end, this research looks at providing bus priority using a dedicated bus lane which is terminated upstream of the intersection, and placing an additional signal at this location, called a pre-signal. Although pre-signals are already implemented in some countries (e.g. UK, Denmark, and Switzerland), an adaptive control algorithm which responds to varying traffic demands has not yet been proposed and analyzed in the literature. This research aims to fill that gap by developing an adaptive control algorithm for pre-signals tailored to real-time private and public transportation demands. The necessary infrastructure to operate an adaptive pre-signal is established, and guidelines for implementation are provided. The relevant parameters regarding the boundary conditions for the adaptive algorithm are first determined, and then quantified for a typical case using a micro-simulation model. It is demonstrated with case studies that, under all considered scenarios, implementing a pre-signal with the proposed adaptive control algorithm will result in the least average person delay at the intersection. The algorithm is expected to function well with a wide range of car demands, bus frequencies, and bus passenger occupancies. Moreover, the algorithm is robust to errors in these input values, so exact information is not required.     

Development of a delay model for unsignalized intersections applicable to traffic assignment

Abstract

This paper develops a model for estimating unsignalized intersection delays which can be applied to traffic assignment (TA) models. Current unsignalized intersection delay models have been developed mostly for operational purposes, and demand detailed geometric data and complicated procedures to estimate delay. These difficulties result in unsignalized intersection delays being ignored or assumed as a constant in TA models.

Video and vehicle license plate number recognition methods are used to collect traffic volume data and to measure delays during peak and off-peak traffic periods at four unsignalized intersections in the city of Tehran, Iran. Data on geometric design elements are measured through field surveys. An empirical approach is used to develop a delay model as a function of influencing factors based on 5- and 15-min time intervals. The proposed model estimates delays on each approach based on total traffic volumes, rights-of-way of the subject approach and the intersection friction factor. The effect of conflicting traffic flows is considered implicitly by using the intersection friction factor. As a result, the developed delay model guarantees the convergence of TA solution methods.

A comparison between delay models performed using different time intervals shows that the coefficients of determination, R ², increases from 43.2% to 63.1% as the time interval increases from 5- to 15-min. The US Highway Capacity Manual (HCM) delay model (which is widely used in Iran) is validated using the field data and it is found that it overestimates delay, especially in the high delay ranges.     

Isolated intersection control for various levels of vehicle technology: Conventional,connected, and automated vehicles

Connected vehicle technology can be beneficial for traffic operations at intersections. The information provided by cars equipped with this technology can be used to design a more efficient signal control strategy. Moreover, it can be possible to control the trajectory of automated vehicles with a centralized controller. This paper builds on a previous signal control algorithm developed for connected vehicles in a simple, single intersection. It improves the previous work by (1) integrating three different stages of technology development; (2) developing a heuristics to switch the signal controls depending on the stage of technology; (3) increasing the computational efficiency with a branch and bound solution method; (4) incorporating trajectory design for automated vehicles; (5) using a Kalman filter to reduce the impact of measurement errors on the final solution. Three categories of vehicles are considered in this paper to represent different stages of this technology: conventional vehicles, connected but non-automated vehicles (connected vehicles), and automated vehicles. The proposed algorithm finds the optimal departure sequence to minimize the total delay based on position information. Within each departure sequence, the algorithm finds the optimal trajectory of automated vehicles that reduces total delay. The optimal departure sequence and trajectories are obtained by a branch and bound method, which shows the potential of generalizing this algorithm to a complex intersection.Simulations are conducted for different total flows, demand ratios and penetration rates of each technology stage (i.e. proportion of each category of vehicles). This algorithm is compared to an actuated signal control algorithm to evaluate its performance. The simulation results show an evident decrease in the total number of stops and delay when using the connected vehicle algorithm for the tested scenarios with information level of as low as 50%. Robustness of this algorithm to different input parameters and measurement noises are also evaluated. Results show that the algorithm is more sensitive to the arrival pattern in high flow scenarios. Results also show that the algorithm works well with the measurement noises. Finally, the results are used to develop a heuristic to switch between the different control algorithms, according to the total demand and penetration rate of each technology.     

Investigating the applicability of exclusive pedestrian phase at two‐phase actuated controlled intersections

The exclusive pedestrian phase (EPP) has been used in many countries to promote walking around downtown areas by increasing the ease and convenience of pedestrian crossing. However, its applicability has not been systematically demonstrated, especially when an intersection is operated in actuated mode. This paper presents an extensive simulation‐based analysis of the applicability of EPP as compared with a normal concurrent pedestrian‐phase pattern at an isolated intersection controlled by actuated logic. Actuated signal control logics for EPP‐actuated and conventional concurrent pedestrian phase‐actuated controls are developed. Both of these control logics consider pedestrian crossing demands and can adapt to changes in vehicle traffic to reduce vehicle delay as well. A simulation model of a two‐phase controlled intersection is built and calibrated based on field data using VISSIM (PTV Planung Transport Verkehr AG in Karlsruhe, Germany). Extensive analysis is conducted to reveal fully the applicable EPP domain in terms of vehicle traffic demand, pedestrian demand, vehicle turning ratio, and pedestrian diagonal crossing ratio. The results show that the performance and applicable domain of EPP are jointly determined by those five factors. EPP significantly outperforms concurrent pedestrian phase if the vehicle turning ratio is greater than 0.6 and the pedestrian diagonal crossing ratio is greater than 0.6. These results can help traffic engineers in choosing the appropriate pedestrian‐phase patterns at actuated signalized intersections. Copyright © 2015 John Wiley & Sons, Ltd.