Dynamic Behaviour of a Mobile Robot Vehicle with a Two Caster and Two Driving Wheel Configuration

The actual trajectory covered by a mobile robot in motion differs from the trajectory planned on the basis of the kinematic characteristics of its directional control system. This difference is essentially related to the behaviour of wheel-road contact, the influence of dynamic loads and the presence of caster wheels.

This paper presents a mathematical model (“ DDPP) which simulates the motion of a generic mobile robot vehicle with a propulsion and directional control system based on two independent driving wheels and two caster wheels.

The differential equations of motion have been obtained by applying modified equations of Lagrange.

The role played by the dynamic loads, the wheel-road contact features and the caster wheels is discussed hereof.     

Comparison of All-Wheel Steerings in the System Driver-Vehicle

Different load or tires and a drive on an ice-coated road can overcharge a driver to such an extend, that the result may be an accident. Therefore the aim of development is a self-acting compensation of the vehicle to different vehicle transfer behaviour (invariant vehicle behaviour).

The calculation of so called optimal characteristics shows, that only rear-wheel steering cannot realize this aim of development. Therefore an additional front-wheel angle, which is not influenced by the driver, is necessary. A transfer function can be calculated in order to get controlled steering of the rear wheels without the influence of load.

It is not possible to realize optimal characteristics, because the parameters of the vehicle are difficult to measure. Only an optimal diagnosis and control of driving condition realize a relief for the driver in every driving situation in order to avoid most of the accidents.

The often demanded sideslip angle compensation only worsens driving conditions on ice-coated roads. Therefore systems which identify the driving condition themselves have to be favoured in any case.     

Off-Road Vehicle Dynamics

Recent developments in off-road vehicle dynamics are reviewed. Progress on this topic and the application of new techniques to the particular problemsassociated with off-road operation tend to lag behind practices established for road vehicles.

The factor which limits further progress is the lack ofappropriate off-road tyre data, in particular, on vibrational and lateral force generation characteristics. Also, a long term study should be aimed at understanding the dynamic behaviour of tyres on yielding surfaces.     

The Lateral Dynamics of Motorcycles and Bicycles

SUMMARY

The paper is a review of the state of knowledge and understanding of the steering behaviour of single-track vehicles, with the main accent on vehicle design, and vehicle design analysis and behaviour prediction.

The body of the paper consists of a chronological account of the steps which have been taken in establishing the current position. Scientific study of the motions of two-wheelers has been in progress for more than 100 years, but progress was slow and many conflicting conclusions were drawn until increasing understanding of tyre mechanics, systematic application of the laws of motion for systems of rigid bodies, digital computation and modern numerical methods, and improved mobile measurement, recording, and data processing capabilities allowed the pace to accelerate.

The current position, which is that a good understanding of the relationship between design and performance has been achieved, but that by no means have all the problems of significance been solved, is described at the end of the paper.     

A Modular Computer Model for the Design of Vehicle Dynamics Control Systems1

This paper describes a multiport approach to computer-aided modeling of vehicle dynamics. The modeling approach produces models that are suitable for the interactive design and evaluation of complex control strategies. The vehicle model which can be used for ride and handling analysis, is built from modular components. The components are programmed using the syntax of the computer aided control system design (CACSD) program EASYS. Seven modeling components are used to create a three-dimensional vehicle dvnamics model. The model is flexible enoug-h to simulate any suspension design with revolute joints.

Each component of the model consists of a FORTRAN subroutine and a main calling module called a macro. To simplify the process of model building, the modeling components in the car model are designed to represent physical elements, such as the spring, damper, link or tire. To create a model, the components, which are represented by blocks, are interconnected through points, located on the blocks, called pons. These ports have been designed to simulate the location of the connection points between the physical elements, as observed in real systems. The construction of multibody models within a CACSD program offers the flexibility of simultaneous interactive simulation of the three-dimensional dvnamics and evaluation of the desien of the controls.

Although modeling of multibody systems using FORTRAN components has been pioneered by Chace, Haug and Orlandea; and bond graph modeling of multibody systems has been investigated by Bos, this approach is novel because:-

The model is included in the control system design program (EASYS). This arrangement allows the designer to exploit the advanced control design tools available in the program. Furthermore, this approach significantly reduces the computation time required for running the model after parameters modification.

The model is built from components that are interconnected by ports which represent the actual physical location of the connection points between the elements. The multiport approach simplifies the model building process for multibody systems. This simplification is achieved by reducing the model of a multibody system to a block diagram form.     

Optimization for Vehicle Suspension II: Frequency Domain

The objective of this study is optimizing the components design of a vehicle suspension system under excitation due to road roughness. The vehicle is modelled as a dynamic system made of masses interconnected by, linear, springs and dampers. The optimizing code provides values corresponding to the caracteristics of masses, dampers and springs which, within a range, minimize the objective function for a defined excitation. This objective function auantifies the vehicle comfort level.

The optimization method used is the sequential linear programming by iteratively applying the Simplex algorithm. The model response is obtained in frequency domain and the vehicle excitation can be either random or deterministic.

The exact nature of the optimization problem, objective function and restrictions, depend on the type of excitation considered.

In succeeding paragraphs, the problem formulation together with a comparison with other authors is presented.     

Messungen von Fahrbahn-Unebenheiten paralleler Fahrspuren und Anwendung der Ergebnisse

Measurement of two track road inputs and theoretical application of the results

The calculation of vehicle response to road-surface irregularity inputs requires the spectral densities of the left and right longitudinal track and their statistical dependence

This paper presents some resluts of parallel profile measurements, three typical german roads have been chosen

Random vibration of two vehicle types are digital-simulated. The dynamic tire load shows that independent suspension systems are more advantageous than beam axles, because by wheel tramp this type increases the dynamic tire load.     

The Dynamics of Single Track Vehicles

The paper contains a brief review of the more subjective aspects of the steering behaviour of single track vehicles, a review of the more significant published work in the field, and an assessment of the current state of understanding and likely ways in which further progress can be made

Attention is drawn to the many areas of agreement between theory and practice and to some areas of disagreement. The greatest need now seems to be for the incorporation of more complex tyre models into vehicle handling models.     

Dynasim 3: A Computer Program for Simulation Of Vehicle Riding Motions

The purpose of this paper is to present analytical techniques for evaluating the dynamic riding behaviour of a vehicle. These techniques have been applied to a fairly sophisticated model of a bus, where a three-dimensional structure, elastic frame and non-linear shock-absorbers have been considered.

A computer simulation program (DYNASIM 3) has been set up, which is actually used at FIAT corporation for evaluating vehicle riding qualities and improving the design process.     

Optimization for Vehicle Suspension I: Time Domain

A numerical procedure for finding the optimum values of a number of parameters describing a model vehicle suspension has been studied. The vehicle has been modelled by dynamic systems of linear springs and dampers, and the goal is to obtain lower acceleration peaks at an elected design point in the vehicle.

The problem is stated as a mathematical programming problem which can be solved by means of the sequential linear programming technique. The procedure has been implemented for a four wheel independent suspension model capable of being subjected to road irregularities and to centrifugal and braking accelerations.     

Nähere Untersuchungen zur stationären Kurvenfahrt von Einspurfahrzeugen

Detailed Investigations of the Steady State Turning of Single Track Vehicles

In the paper the steady state turning of single track vehicles on a horizontal, even road is investigated, supposing the air to be at rest. The vehicle model used has six degrees of freedom: rolling, yawing, pitching and bouncing of the vehicle, rotation of the front wheel system (steering) relatively to the main frame and distortion of the rear wheel system due to limited stiffness of its linkage, and also takes into account wind drag and gyroscopic effects generated by wheels and other vehicle components. A special importance is given to the geometry of the vehicle

The results show a comparison of two types of motorcycles with different geometries and tires. To characterize the vehicle behaviour the roll, side slip and steering angle as functions of the normal acceleration are used. A more detailed study in respect to the steering torque is added.     

Longitudinal Oscillations of Vehicle/Trailer Combinations Induced by Overrun Braking

A mathematical model for the representation of longitudinal oscillations which can occur in car/trailer systems in braking, when the trailer brakes are applied through compression of the towing hitch, is described. The model is used to show how the trailer braking system parameters affect the steady deceleration performance of the vehicle combination, and the stability, in the linear system sense, of the steady motions. The sensitivity of the stability to other system design parameters is also examined.

Digital simulation of the motions occurring in response to a step input of car braking torque is reported, with the results confirming the predictions of the linear stability analysis, and also showing the influence of backlash in the trailer brake actuating mechanism.

The system is shown to be capable of self-excitation in a “shunting” mode, in which the car and trailer motions are in antiphase, with the stability/damping property critically dependent on drawbar damping, and only weakly dependent on other system parameters. The characteristic frequency of the “shunting” mode oscillations is shown to be controllable via the stiffness of the trailer brake linkage, but this frequency is closely related to the steady drawbar deflection which occurs in uniform deceleration.

The model behaviour described provides a basis for the design of relevant systems whose longitudinal dynamic characteristics will be satisfactory.     

Critical Speed and Limit Speed in Phenomena of Lateral Instability on Railway Vehicles

A comparison between theoretical calculations on dynamic lateral behaviour of railway vehicles and experimental results shows quite a sizeable difference between the calculated critical speed and the actual speed at which side impact phenomena will repeatedly occur between wheel flange and rail (running speed limit), such impact speed being remarkably lower than calculated.

Another typical experimental aspect is that the running speed limit will considerably vary for the same vehicle depending on the test track conditions. Such difference is usually attributed to alterations of the wheel-rail contact surfaces, only.

This paper will discuss some concurrent causes which may prove far from negligible, such as the effects of track defects, an amplification of the dynamic lateral displacement between wheel and rail on approaching the critical speed, the track mechanical properties, and in particular the track lateral rigidity.

The influence of some geometrical factors typical of the wheel-rail contact, such as side clearance and linearized conicity, will also be discussed. The approach is based on the application of statistical methods to dynamic linear systems.     

Dynamic Measurements in the Research and Development of Rail Vehicles

This paper reviews the measurements which are necessary to all aspects of vehicle dynamics as applied to rail vehicles. Although an attempt has been made to introduce some reference to measurements made in Europe and America, the detailed discussion has been limited to those techniques employed by British Rail. This has the advantage that the discussion can be first hand and therefore more specific.

For convenience the measurements have been collected together under four broad headings.

1. Measurements of rail system data.

2. Measurements of vehicle parameters.

3. Measurements to validate theory and predictions.

4. Measurements of vehicle performance.     

A Driver Model Based on the Cerebellar Model Articulation Controller

A model of driver behavior is described which is based on a current theory of neurophysiological processes occurring in the cerebellum. The model learns to control the vehicle through experience, provides discontinuous ramp steer inputs to the vehicle, accepts discontinuous input data, and is applicable to all control situations.

The model is implemented on a simple simulation model of a car and learning is accomplished by the use of an explicit driver model which drives the vehicle along a specified trajectory.     

Berechnung des extremen Lenk- und Bremsverhaltens von Sattelkraftfahrzeugen

Simulation of Steering and Braking Behaviour of Tractor-Semitrailer Vehicles in Extreme Situations

This paper deals with the simulation of the behaviour of tractor-semitrailer vehicles at braking on wet, slippery road surface. The nonlinear model used for the computation enables to simulate extreme situations at wheel locking and swerving

The instabilities during braking such as jackknifing and trailer swing as well as non steerability are investigated. Straightline braking shows the influence of cornering on the behaviour during braking in a turn.     

Survey of Wheel—Rail Rolling Contact Theory

This paper describes the theory of frictional rolling contact as far as it is significant for the wheel-rail system. It is divided into two parts.

The first part, mostly non-mathematical, contains a historical survey from the times of Carter and Fromm (1926) to the present day, in which all aspects of rolling contact theory are discussed. Included are a quantitative account of the results of Hertz theory (Section 3), and a table of the creepage and spin coefficients.

The second part gives a present day account of the simplified theory (Section 4), and of the exact linear and non-linear theory (Section 5).

The paper closes with some recommendations for future research, of which the most pressing is a thorough investigation of the accuracy of simplified theory.     

Dynamic Behaviour of Ore Wagons in Curves at Malmbanan

The transportation of ore can be made more cost efficient by use of bigger and heavier trains. An increase in axle load is thereby wanted. The fleet of ore wagons of today at Malmbanan/Ofotbanan in northern Sweden and Norway has to be updated. It is of interest to find out if it is possible to allow a higher axle load on the track with new wagons

To be able to understand and predict the effects on track wear depending on what type of vehicle that is in use, the contact forces between wheels and rails have to be determined. A computer aided analysis has been made of the dynamic behaviour of three test vehicles equipped with different types of three-piece bogies running at Malmbanan. The vehicles are modelled and their interaction with the track is analysed using the multibody simulation package GENSYS

The simulations show that, even if the axle load is increased from 25 tons to 30 tons and the velocity is increased from 50 km/h to 60 km/h, it is possible to reduce lateral track forces and wear in curves by using a different bogie than the standard three-piece bogie used today.     

Vertical Load-Deflection Behaviour of a Pneumatic Tire Subjected to Slip and Camber Angles

In this paper the vertical load-deflection behaviour of a pneumatic tire has been studied theoretically. A simple mathematical model which is especially suitable for a tire applied by a side force has been developed. Researches carried out in the past show that the tire vertical stiffness varies neither proportionally nor symmetrically as the slip angle of a cambered tire is changed. This effect can be explained by the theory developed here.

The model predictions have been verified using experimental results obtained from literature. Moreover, tire cornering characteristic curves obtained under different test conditions, i. e. during increasing of the slip angle the vertical load is kept constant or not, have been discussed through a simulation example. This study shows that the characteristic curves vary rather considerably under the different conditions.