Cycle-simulation turbulence modelling of IC engines

Numerical simulations of IC engines are of high interest for automotive engineers worldwide. The simulation models should be as fast as possible, low-computational effort and predictive tool. The correct prediction of turbulence level inside the combustion chamber of spark ignition engines is the most important factor influencing to the engine working cycle. This paper presents a development of the k-ε turbulence model applied to the commercial cycle-simulation software with the high emphasis on the intake part. The validation was performed on two engine geometries with the variation of engine speed and load comparing the cycle-simulation results of the turbulent kinetic energy and in-cylinder temperature with 3-D CFD results. In order to apply the cycle-simulation turbulence model for the simulation of entire engine map, the parameterization model of turbulence constants was proposed. The parameterized turbulence model was optimized using NLPQL optimization algorithm where the single set of turbulence model parameters for each engine was found. A good agreement of the turbulent kinetic energy during the expansion was achieved when the turbulence affects the flame front propagation and combustion rate as well.     

Modelling and control of a new differential steering concept

This paper presents a new steer-by-wire concept using an all-wheel drive vehicle layout with in-wheel motors while completely omitting the application of any dedicated steering device. Steering is based on the so-called differential steering principle which generates the necessary steering moment about the kingpins by a traction force difference between left and right sides of the vehicle. In order to investigate the behaviour of the vehicle and to design the underlying control algorithms, a planar vehicle model is presented, where the vehicle is described as constrained non-holonomic system requiring a special treatment. A state feedback linear controller for controlling of the lateral dynamics of the vehicle at higher speeds and a simple PI angle controller for low-speed manoeuvring are developed. The resulting behaviour of the system is investigated by various simulation experiments demonstrating a comparable steering performance of the new steering concept as that of conventional passenger cars.     

Protecting Rhode Island's coastal salt ponds: An economic assessment of downzoning

Abstract

In southern Rhode Island, there is growing concern that housing and recreational demands will soon overwhelm the capacity of the coastal salt ponds to absorb wastes, produce seafood, and maintain scenic qualities. As a result, coastal towns have been studying the feasibility of using land controls such as downzoning to protect these coastal amenities. The paper presents an economic analysis of the downzoning program proposed in the town of South Kingstown. Hedonic price and contingent valuation methods are used to value coastal amenities. The estimated net present value of “swimmable” water is shown to be $3.1 million.     

Origin–destination table disaggregation using biproportional least squares estimation

This paper describes a group of techniques for disaggregating origin–destination tables for travel forecasting that makes explicit use of observed traffic on a network. Five models within the group are presented, each of which uses nonlinear least-squares estimation to obtain row and column factors for splitting trip totals from and to larger geographical areas into smaller ones. The techniques are philosophically similar to Fratar factoring, although the solution method is quite different. The techniques are tested on a full-sized network for Northfield, MN and are found to work effectively.     

Estimation of the effects of aircraft noise on residential satisfaction

This study assesses the effects of aircraft noise on residential satisfaction, an important indicator of subjective well-being. A structural equation model is specified that estimates the relationships between objective variables, noise annoyance variables and residential satisfaction. Secondary data-analysis is used to estimate the model. The survey was conducted in 1996/1997 among the population living within a 25-km radius of Amsterdam Schiphol, the largest airport in the Netherlands. The effect of aircraft noise annoyance is found to be relatively small. In addition, the objective level of aircraft noise exposure is found to be a better predictor of residential satisfaction than its subjective counterpart. The most important determinants of residential satisfaction are found to be road traffic noise annoyance, age and neighbor noise annoyance.     

Scantling multi-objective optimisation of a LNG carrier

Numerous real-world problems related to ship design can be solved by various alternatives. However, the scantling design has conflicting objectives such as minimum production cost, minimum weight and maximum moment of inertia (stiffness). Therefore a multi-purpose solution had to be settled in order to meet all these requirements at once. Ship design is a complex endeavour requiring successful coordination of many different disciplines, both technical and non-technical. Basic design is the least defined stage of the ship design process and seeks to define the optimal amidships section structure. For that purpose, recent improvements have been made to a numerical tool in order to optimise the scantling of ship sections by considering production cost, weight and moment of inertia in the optimisation objective function. A multi-criteria optimisation of a LNG carrier is conducted in this paper to illustrate the analysis process. Pareto frontiers are obtained and results have been validated by the Bureau Veritas rules. The methodology presented in this paper has demonstrated its effectiveness in optimising scantling of ships at a very early design stage thanks to a management of critical problems usually studied at a later stage of the design.     

Methodology for the accuracy improvement of FEM beam type T-junctions of buses and coaches structures

The analysis of structures with finite elements methods (FEM) represents a widely spread technique. For large tubular structures similar to the buses and coaches upper structures, beam type elements are utilized due to the fact that these elements provide satisfactory results at relatively reduced computational performances. However the beam type elements have a main disadvantage determined by the fact that the modeled joints have an infinite rigid behavior. This shortcoming determines a stiffer behavior of the modeled structures which translates into an error source for the structural simulations (up to 45%). To overcome this problem, a simple methodology was conceived and an alternative optimized equivalent beam model obtained. The methodology studies the behavioral characteristics of beam modeled T-junctions determining their limitations and comparing them to equivalent T-junctions modeled with shell and volume elements. This way an improved Tjunction has been obtained, in which the behavioral error was reduced to less than 5%. Furthermore the FEM obtained results were validated with real T-junctions.     

Network representation,continuum approximations and a solution to the spatial aggregation problem of traffic assignment

This paper complements the preceding one, which showed how one could modify equilibrium traffic assignment algorithms for networks with many centroids. In this one it is shown how one can substitute centroids by zones with continuous population densities. The technique, which is mathematically guaranteed to approximate a flow pattern in accordance with Wardrop's user equilibrium criterion, requires some geometrical calculations which can be handled off-line. With the suggested approach, it is possible to represent the spatial distribution of trip ends more realistically and this allows traffic assignment models to capture the effects of short and intrazonal trips in a way previously impossible. The method is shown to be computationally feasible.     

Finite element modeling of static tire enveloping characteristics

To investigate static tire enveloping characteristics, a three dimensional (3-D) finite element model is proposed. The vertical stiffness of the tire is studied on a flat surface with and without cleat. Tire rubber materials and cord layers are represented independently using “rebar” elements available in MSC Marc Mentat. Comparisons of numerical and experimental results are given to show the validity of the proposed model. It is shown that after a certain displacement, the results of the proposed model agree well with experimental results. In addition, the model results show that regardless of the type of the cleat placed under the rim center (hub center), all vertical force curves intersect after a certain displacement, which indicates typical static enveloping characteristics. Moreover, another typical characteristic of the radial tires that is unlike those of bias-ply constructions confirms that the contact patch does not expand laterally after a level vertical load is applied to the tire, which is directly related to fuel consumption and tire tread life.