建构中高职衔接物流专业模块化课程体系研究

建立中职与高职的有效衔接是完善职业教育体系和提高职业教育质量的关键，通过分析目前物流专业中高职课程衔接在课程体系、教学计划、教学管理、考评制度方面存在的割裂现象，提出应借鉴国外的做法，加强宏观制度建设，建立统一的职业能力导向的模块化课程体系。     

桥梁单板受力的原因及预防措施探讨

从宏观角度分析桥梁预制板单板受力的一般规律,以及形成单板受力的原因,并从设计角度提出克服单板受力的措施,尤其是提出设置横向预应力是解决单板受力的有效措施,可供设计人员参考.     

斜向波浪对斜坡堤胸墙作用力的试验研究

斜坡堤胸墙的稳定性主要受到波浪作用的影响,而且实际工程中斜坡堤多受斜向波浪作用。通过斜向与正向不规则波对斜坡堤胸墙作用的物理模型试验研究,分析斜坡堤单个胸墙所受的斜向波浪总力的折减系数随水位和波浪入射角度的变化规律,并与斜向波浪对单元直立堤的作用情况进行对比。结果表明:斜坡堤单个胸墙所受的斜向波浪总力的折减系数总体上随着水位的降低而变小,随着波浪入射角度的减小而变小;斜向波浪总浮托力的折减系数一般小于总水平力的折减系数;在不同水位和波浪入射角下,斜坡堤单个胸墙所受的斜向波浪总力的折减系数与单元直立堤有一定差别。     

浅埋顶管沉井周边土体的三维破坏形状及沉降研究

为研究顶管沉井及周边土体在顶进力作用下的形变范围与大小，以加固旋喷桩作为沉井周围加固体建立ABAQUS软件计算模型，并将模拟结果与工程实例、PLAXIS 3D软件所得结果进行对比分析。同时，采用广州地区花岗岩残积土进行室内沉井模型试验，并通过试验结果对数值模拟结论进行验证，得出结论如下： 1）在开挖基坑前达到设计强度的旋喷桩能有效减小基坑周边土体塌陷变形、坑底隆起。2）在施加工作顶推力下，前侧主动区首先出现贯通裂缝，竖向位移斜率增大出现明显拐点；继续增大顶推力，土体位移会急剧增大导致地表沉降严重。3）对于后背土体，在顶推力作用下，地表破裂线的切线角度从0°逐渐增大至45°+φ/2，导致破裂范围也不断扩大；达到45°+φ/2处后，继续施加顶推力会导致短轴方向破坏范围扩大的速度较长轴方向的速度更快；三维空间中被动区破坏土体在地表处产生形状为椭圆的破坏面，椭圆长轴方向为顶推轴线方向，被动破坏体呈现为牛角状椭圆楔体。     

基于地基回弹因素的盾构隧道管片上浮预测

针对软弱地层盾构隧道管片脱出盾尾后出现的上浮问题,分析盾构施工过程中管片上浮的诱因,得出软弱地层中管片的上浮主要是地层应力重分布产生的地基回弹力引起的。在此基础上建立隧道开挖动态模型,分析隧道上浮量变化规律以及地层特性对管片上浮量的影响规律,得出地层弹性模量和管片上浮量呈一定的指数关系,且弹性模量对管片上浮量的影响远大于地层黏聚力和内摩擦角。通过力平衡理论计算盾构开挖引起的地层回弹力、管片上浮量以及隧道上浮影响的地层高度范围,并通过对珠江狮子洋工程管片上浮量的计算与实测对比,证明该公式的合理性,为盾构隧道工程中考虑地基抗力引起的管片上浮量预测提供一种新的方法。     

约束对隧道二次衬砌早期温度应力分布的影响

为了解决隧道工程渗水问题,基于某隧道工程,采用MIDAS-GEN对其二次衬砌早期模筑混凝土进行非稳定温度应力场以及周围约束进行研究。研究结果表明:约束可以改变隧道的早期拉应力场的分布,具有外围约束的隧道二次衬砌的拉应力为隧道厚度中间最大,无约束隧道的拉应力为外部最大,约束可以减小隧道外部区域的拉应力,使得远离约束区域的拉应力变大,而无约束隧道的拉应力分布与之相反。根据温度应力分布特点,建议在设计方面适当增大二次衬砌中间与外侧的配筋,在施工方面减小初期支护与二次砌衬之间约束等。     

Design of tyre force excitation for tyre–road friction estimation

Knowledge of the current tyre–road friction coefficient is essential for future autonomous vehicles. The environmental conditions, and the tyre–road friction in particular, determine both the braking distance and the maximum cornering velocity and thus set the boundaries for the vehicle. Tyre–road friction is difficult to estimate during normal driving due to low levels of tyre force excitation. This problem can be solved by using active tyre force excitation. A torque is added to one or several wheels in the purpose of estimating the tyre–road friction coefficient. Active tyre force excitation provides the opportunity to design the tyre force excitation freely. This study investigates how the tyre force should be applied to minimise the error of the tyre–road friction estimate. The performance of different excitation strategies was found to be dependent on both tyre model choice and noise level. Furthermore, the advantage with using tyre models with more parameters decreased when noise was added to the force and slip ratio.     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.     

基于一维-三维耦合仿真的进气系统优化方法

提出了基于一维-三维耦合仿真的进气系统优化方法,此方法兼具CFD对进气系统三维流动特性准确描述与一维仿真对内燃机进气系统全局控制的优点。建立了进气歧管三维模型,采用GT-Power软件进行缸内工作过程模型仿真,根据试验数据标定仿真模型。通过一维-三维耦合仿真计算得到进气歧管各转速下的流动参数,以此作为CFD仿真的边界条件,优化进气歧管的结构参数。通过整机试验对进气歧管流动性能进行了验证。试验结果表明,该方法能够较好地指导进气歧管设计。     

柴油机活塞销孔型线对比分析研究

针对某柴油机活塞销孔的磨损问题,分别借助有限元方法和EHD仿真方法研究了不同销座结构匹配多种销孔型线对接触应力的影响,及不同活塞销孔型线对润滑特征评价参数的影响。综合研究表明,活塞销孔型线与热变形匹配不合理所引起的润滑状态恶化是导致活塞销孔磨损的直接原因,因此通过合理调整销孔型线可使接触应力均匀,润滑状态良好,并有效降低活塞销座磨损风险。