大跨径连续刚构桥的温度效应分析

以魏家洲特大桥为例,按照我国公路桥涵设计规范、英国BS5400规范、新西兰规范确定不同的计算模式,对大跨径连续刚构桥进行温度效应分析,得出：温度应力在大跨径连续刚构桥整个桥梁设计中占有很大的比重,且采用不同的温度梯度计算模式,所得到的梁内温度应力值相差较大,甚至出现异号的温度应力.     

沥青混凝土转运车对提高道路施工质量的试验研究

对道路摊铺过程中采用摊铺机直接摊铺作业和采用徐工AT1000A型转运车与摊铺机联合施工作业的试验路面效果进行了对比,分析了摊铺温度场和骨料摊铺效果.结果证明使用沥青混凝土转运车是提高道路施工质量的有效手段.     

多年冻土区钻孔灌注桩施工过程热力特性研究

钻孔灌注桩水化热会暖化冻土引起桩基承载力下降,以桩基水化热在时间与空间上的影响效应为研究目的,结合青藏公路G214沿线查拉坪旱桥桩基观测数据,分析水化热对地温场的扰动范围以及桩周土回冻时间,给出灌注桩18 d内的养护温度。结果表明:水化热对距桩1.95 m以外地温影响微弱;144 d后桩侧温度降至0℃以下,229 d后桩侧温度低于-0.5℃;2 a后桩侧基本回冻至天然地温,此时承载力已达到设计要求。桩基混凝土养护温度前5 d在10℃以上,5~12 d在5℃以上,12~15 d为2℃以上,15~18 d仍高于0℃。通过数值仿真给出混凝土入模温度及桩基施工时间对桩周温度场的影响,模拟结果显示,该区域的灌注桩施工可以在相应规范规定范围内提高混凝土入模温度;灌注桩施工可以在冷季进行,但要做好5 m以上深度桩基混凝土的温控措施。     

A design method of tensile triangles and low transformation temperature weld metal for reduction of stress concentration and residual stress of welded joints

Stress concentration and residual stress have a significant influence on fatigue life of welded joints. In order to reduce the stress concentration of welded joints, a mathematical design method of tensile triangles (MTT) based on bionics was applied to weld shape design. Accordingly, the stress concentration of various weld beads in the corner boxing welded joint and the fillet welded T-joint was dissected using our in-house FEM software JWRIAN. It was found that there existed a large stress concentration in the conventional welded joints, whereas those welded joints with elongated weld bead were accompanied by a lower stress concentration, especially for elongated weld bead with MTT design. Furthermore, among the weld shapes of the corner boxing fillet welded joint, the rectangle shape of weld bead had the minimum stress concentration factor (1.05). For the fillet welded T-joint with MTT design, the stress concentration of weld toe decreased dramatically with the increase of the index of designed shape, but there was a minor difference of stress concentration at weld root between the weld beads with MTT design. In addition, application of low transformation temperature (LTT) weld metal utilizing martensitic transformation to the fillet welded T-joints can produce compressive residual stress at weld toe.     

长大货物车适应THDS轴温探测技术的研究

针对不适应THDS轴温探测系统的长大货物车,分析论证了现车轴箱改进方案适应THDS轴温探测的不足,并提出了轴箱优化方案。经计算、试验和装车验证表明,新轴箱可行、有效、安全,满足THDS轴温探测要求,保证了长大货物车运输安全。     

兰州地铁地温分布特性及其演化规律

以兰州地铁所在地区为研究对象,实测地铁隧道开挖前的地温(简称为初始地温),根据实测数据,提出地铁初始地温预测模型公式。采用非稳态传热的数值模型,分析运营条件下地铁隧道围岩温度的演化规律。结果表明:兰州地铁初始地温随环境气温和埋深的变化而变化;年变温层位于自地表至埋深12m处;年恒温层位于埋深12m及其以下,温度为15℃左右;年变温层中,1年内初始地温变化规律与环境气温变化规律相似,近似呈正弦曲线状分布,但存在相位滞后的现象;1年中初始地温的振幅随埋深的增大呈指数下降趋势。在隧道内空气与围岩之间热交换中,兰州地铁隧道围岩的温度及其梯度、热透厚度(未达到极限时)均与隧道内环境温度、热交换时间成正相关关系,但与距隧道内壁的距离成负相关关系。     

某型直流充电柜温度场仿真

对某型直流充电柜满负载工况下温度场进行仿真,根据实验测量数据验证仿真结果准确性,成功完成了对充电柜温度场的建模仿真工作,并实现对初始模型的简化,为对整个充电站进行温度场建模仿真奠定了基础。     

The problem of cold starts: A closer look at mobile source emissions levels

While the phenomenon of excess vehicle emissions from cold-start conditions is well known, the magnitude and duration of this phenomenon is often unclear due to the complex chemical processes involved and uncertainty in the literature on this subject. This paper synthesizes key findings regarding the influence of ambient and engine temperatures on light-duty vehicle (LDV) emissions. Existing literature, as well as analytical tools like the U.S. Environmental Protection Agency’s Motor Vehicle Emission Simulator (MOVES), indicate that while total vehicle emissions have dropped significantly in recent years, those associated with cold starts can still constitute up to 80% for some pollutant species. Starting emissions are consistently found to make up a high proportion of total transportation-related methane (CH₄), nitrous oxide (N₂O), and volatile organic compounds (VOCs). After 3–4 min of vehicle operation, both the engine coolant and the catalytic converter have generally warmed, and emissions are significantly lower. This effect lasts roughly 45 min after the engine is shut off, though the cooling rate depends greatly on the emission species and ambient temperature. Electrically (pre-)heated catalysts, using the bigger batteries available on hybrid drivetrains and plug-in vehicles, may be the most cost-effective technology to bring down a sizable share of mobile source emissions. Trip chaining (to keep engines warm) and shifting to non-motorized modes for shorter trips, where the cold start can dominate emissions, are also valuable tactics.     

大跨度钢箱梁斜拉桥中跨合龙关键技术

以4座主跨超过400 m的钢箱梁斜拉桥中跨合龙控制为背景,对大跨度钢箱梁斜拉桥中跨合龙的2种方法进行对比分析,对合龙各主要工序的关键技术进行研究。提出了合龙段配切长度的计算公式和合龙口宽度连续观测的测点布置方式。建议:在调整好合龙口姿态后可不加压重,也可不采用临时劲性骨架锁定;采用无线采集设备采集合龙口结构的温度场,用激光测距仪测量合龙口宽度以提高观测效率和安全性;在悬臂施工阶段关注梁长累计误差并通过调整后续梁段的制造长度消除之。     

Climate change behaviors related to purchase and use of personal cars: Development and validation of eco-socially conscious consumer behavior scale

A constantly changing environment and global warming are issues that are recognized at all global forums. One of the major reasons for global warming is the emission of greenhouse gasses which is primarily caused by use of personal cars as means of transport. This study reports on the development of an eco-socially conscious consumer behavior (ESCCB) scale specific to purchase and use of personal cars, based on samples of actual automobile customers in Pakistan. Using mixed method approaches, the results of 3 studies yield a 9-item three-dimensional scale (eco-social conservation, eco-social use, and eco-social purchase) with satisfactory reliability, construct validity and nomological validity. Second-order factor analysis revealed that eco-social purchase was the most important dimension, followed by eco-conservation and eco-social use. A test of nomological behavior shows that the scale is positively associated with a related construct: environmental concern. This study advances the literature on pro-environmental behaviors by introducing a conceptual definition of ESCCB related to personal car purchase and use, developing a measure for the ESCCB concept and validating the scale in the context of an emerging economy, Pakistan. The scale provides important insights for marketers in the automobile industry for remodelling marketing plans, as well as for environmentalists focusing on strategies to bring change in consumer behavior.