环氧沥青在大跨径钢桥面粘结层中的应用研究

粘结层材料和施工技术是大跨径钢桥面铺装的关键技术之一。根据某公路大桥桥面铺装粘结层的设计过程和特性，提出了环氧沥青粘结层的设计方法。     

砂浆锚杆的有限元模拟方法探讨

针对现有砂浆锚杆有限元模拟方法的局限性与不足，在深入探讨砂浆锚杆的力学机理的基础上，提出了一种包含锚杆、砂浆以及接触面的新型复合锚杆单元，该单元不仅能反映锚杆的轴向受力作用，还能反映锚杆的抗弯以及锚杆与岩体接触面的剪切滑移效应，并利用有限元基本理论，推导了新型复合锚杆单元刚度矩阵及相关计算公式，并编制了相应的计算程序，工程实例分析表明：模型能够满足工程要求，具有一定的理论与工程实用价值。     

大跨径连续刚构桥的温度效应分析

以魏家洲特大桥为例,按照我国公路桥涵设计规范、英国BS5400规范、新西兰规范确定不同的计算模式,对大跨径连续刚构桥进行温度效应分析,得出：温度应力在大跨径连续刚构桥整个桥梁设计中占有很大的比重,且采用不同的温度梯度计算模式,所得到的梁内温度应力值相差较大,甚至出现异号的温度应力.     

焊接残余应力对深潜器耐压球壳承载能力的影响

耐压球壳通常采用焊接方式将两个半球壳连接成整球,在焊缝处产生的接近材料屈服强度的焊接残余应力对球壳的承载能力有多大的影响,是否需要做焊后消除残余应力处理,将直接影响球壳的安全性和生产成本。而现有对球壳极限强度计算,无论是理论计算还是数值计算,均只考虑了球壳初始缺陷中的几何缺陷对球壳极限强度的影响。该文将在现有的耐压壳极限强度设计公式基础上,采用数值计算的方法对耐压球壳的焊接过程进行数值模拟,得到焊后球壳的焊接残余应力分布,并在此基础上考虑残余应力对球壳极限强度的影响,结果表明,对于大潜深厚球壳,焊接残余应力对耐压球壳承载能力影响不显著,为大深度潜器耐压球罐是否需做焊后消除残余应力处理提供了一定的参考依据。     

小方型系数船舶的船体波浪载荷综合研究

从船级社规范对于不符合主尺度比要求的船舶船体梁波浪载荷的规定出发,采用理论预报和船模试验2种综合方式,进行了小于0.6方型系数、高航速、高海况目标船的波浪载荷研究.从规范对波浪载荷的线性理论预报值进行的非线性修正,修正后中拱和中垂波浪弯矩绝对值之和与线性理论预报极值全幅值相等出发,阐述所研究船特殊主尺度比下的模型试验结果、三维非线性水弹性理论预报结果显示出的波浪载荷非线性行为;同时综合模型试验与理论预报的共同规律,研究不同波高、航速、浪向等非常规船型船体波浪载荷的强非线性行为,从而认为规范基于的线性理论预报值进行非线性修正的统一规定太过笼统,进而建议规范对波浪载荷的非线性修正予以进一步的明确区分和规定.     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

A regression and beam theory based approach for fatigue assessment of containership structures including bending and torsion contributions

Container shipping has been expanding dramatically during the last decade. Due to their special structural characteristics, such as the wide breadth and large hatch openings, horizontal bending and torsion play an important role to the fatigue safety of containerships. In this study the fatigue contributions from vertical bending, horizontal bending and torsion are investigated using full-scale measurements of strain records on two containerships. Further, these contributions are compared to results from direct calculations where a nonlinear 3D panel method is used to compute wave loads in time domain. It is concluded that both bending and torsion have significant impacts on the fatigue assessment of containerships. The stresses caused by these loads could be correctly computed by full-ship finite element analysis. However, this requires large computational effort, since for fatigue assessment purposes the FE analysis needs to be carried out for all encountered sea states and operational conditions with sufficient time steps for each condition. In this paper, a new procedure is proposed to run the structure finite element analysis under only one sea condition for only a few time steps. Then, these results are used to obtain a relationship between wave loads and structural stresses through a linear regression analysis. This relation can be further used to compute stresses for arbitrary sea states and operational conditions using the computed wave loads (bending and torsion moments) as input. Based on this proposed method for structure stress analysis, an efficient procedure is formulated and found to be in very good agreement with the full-ship finite element analysis. In addition it is several orders of magnitude more time efficient for fatigue assessment of containership structures.     

压载荷下骨材贯穿孔孔边应力集中模型试验

以船舶双层底结构为研究对象开展模型试验,研究板材中的开孔在承受压力载荷作用下的孔边应力分布情况,分析压力载荷下不同开孔孔型以及不同补强结构对孔边应力分布情况的影响。在此基础上,开展相关仿真分析,将试验结果与有限元仿真结果进行对比,验证有限元仿真的准确性。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

长江南京以下12.5 m深水航道工程新型筑堤结构

针对长江南京以下12.5 m深水航道二期工程落成洲河段整治建筑物的特点,提出在堤高为3.0~6.5 m的堤段采取倒T型构件混合堤替代抛石斜坡堤的新型筑堤结构。对混合堤结构在波、流共同作用下的稳定性采用翻坝水流力和合田波浪力计算公式进行理论受力分析,并通过三维物理模型试验对波、流共同作用下混合堤结构稳定性进行验证,结果判定为稳定。新型倒T型构件混合堤减少块石用量,有利于缓解大宗石料供应难度,适应环保需求,同时减少水上施工时间,加快施工进度。该结构已成功申请实用新型专利,可为类似工程提供指导和借鉴。