转K6型转向架变刚度弹簧组的疲劳寿命分析

对转K6型变刚度弹簧组的疲劳强度进行了理论分析,利用名义应力法对疲劳寿命进行了估算,利用考虑实际重车载荷下的“当量挠度法”对疲劳强度进行了校核,同时进行疲劳试验对理论分析进行了验证.     

重庆市城镇土地集约利用时空动态变异分析

通过建立城镇土地集约利用度评价指标体系,运用改进的熵值法,对重庆市1997—2005年各城镇土地集约利用程度进行评价.根据评价结果,对重庆市土地集约利用程度进行区域性的时空变异分析,总结出全市各区域土地集约度时空变异规律及其形成原因,提出未来提高城镇土地集约利用度的政策建议.     

粉喷桩技术在高速公路软基处理中的应用

采用粉体喷射水泥搅拌桩是高速公路处理软土路基的有效方法，它具有就地搅拌原状土成桩效率高、成本低，施工占地小．施工过程中无噪音、无震动，环境污染小等特点，值得推广使用。     

沥青层底裂缝几何函数和权函数分析

为了更好分析沥青路面的裂缝开裂问题，以裂缝面受均匀拉应力为参考荷载，利用有限元方法计算出不同沥青层底裂缝长度的应力强度因子，从而得到不同裂缝长度的离散几何函数值，再根据这些离散几何函数值，为沥青层底裂缝拟合出了3个几何函数F(a/b）。并利用另外两种荷载对这3个几何函分别进行了检验，用3个数根据汉函数理论计算出的应力强度因子和有限元计算出的应力强度因子在所有计算范围内都吻合得很好。利用这几何函数得到了裂缝所有计算范围的权函数，并绘图进行了对比分析。     

磁处理对南海原油凝点的影响规律研究

通过对原油进行磁处理,可以改善原油的流动性,降低其输送成本。通过控制磁化温度、磁化转速和磁化强度,对模拟南海原油油样进行磁处理后凝点变化规律进行了研究。结果表明:磁处理能降低南海原油的凝点,磁化温度、磁化转速和磁化强度对南海原油的凝点均有影响。在40~80℃的温度区间内,磁化温度越高,磁处理降凝效果越好;在0~100 mT的磁场强度范围内,随着磁化强度增加,凝点具有不断降低趋势;最优的磁化转速为1000 r/min,在此转速下,实验油样凝点降低了4.7%。     

Approximate weight functions of stress intensity factor for a wide range shapes of surface and an embedded elliptical crack

This paper describes the application of weight function for stress intensity factor in a surface crack with a wide range of crack shapes. Based on the weight function representation proposed by Wang and Glinka (2009), an extended formulation of the weight function for surfaces and embedded cracks is performed. The unknown parameters in the formulations were determined from reference values of stress intensity factor for a surface and an embedded crack given by finite element analysis with the J integral method. The effectiveness of the proposed weight functions has been verified by comparing with the stress intensity factors given by finite element analysis and available approximated solutions under several loading conditions.     

Dynamic anti-plane interaction between an impermeable crack and a circular cavity in an infinite piezoelectric medium

Wave propagation in an infinite elastic piezoelectric medium with a circular cavity and an impermeable crack subjected to steady-state anti-plane shearing was studied based on Green＇s function and the crack-division technique. Theoretical solutions were derived for the whole elastic displacement and electric potential field in the interaction between the circular cavity and the impermeable crack. Expressions were obtained on the dynamic stress concentration factor （DSCF） at the cavity＇s edge, the dynamic stress intensity factor （DSIF） and the dynamic electric displacement intensity factor （DEDIF） at the crack tip. Numerical solutions were performed and plotted with different incident wave numbers, parameters of piezoelectric materials and geometries of the structure. Finally, some of the calculation results were compared with the case of dynamic anti-plane interaction of a permeable crack and a circular cavity in an infinite piezoelectric medium. This paper can provide a valuable reference for the design of piezoelectric actuators and sensors widely used in marine structures.     

骨质疏松性骨折愈合过程中骨痂局部生物力学改变的实验研究

目的　探讨骨质疏松骨折动物模型愈合过程中骨痂局部生物力学性能的变化。方法　利用大鼠骨质疏松胫骨骨折模型 ,测量了骨痂局部弹性模量和极限强度的变化。结果　骨质疏松骨折愈合过程中 ,弹性模量和极限强度均随着骨折愈合过程的进行而增加 ,在骨折后 3 5d编织骨完全形成后 ,极限强度与非骨折组相比无明显差别 ,而弹性模量尚有明显差别 ;在同一时间点与正常骨折组相比均无明显差别。结论　骨质疏松骨折骨痂局部的弹性模量及极限强度的变化模式与正常骨折骨痂相比无明显差别。     

岩溶区盾构带压开仓掌子面加固关键技术研究

针对盾构过岩溶区带压开仓常规加固所存在的弊端,以深圳地铁16号线龙龙区间为背景,研究注浆加固关键技术。通过试验配制具有一定胶凝性能的快凝低强度浆液,并利用研制的可伸缩液压注浆装置,将浆液直接快速输送至地层薄弱点,使其渗入掌子面岩土裂隙,实现掌子面整体加固、阻断外部来水和密封土仓高压气,快速稳固刀盘、土仓土体,同时做好盾尾止水,保证换刀安全。该方法与常规衡盾泥加固相比,经济效益显著,对复合地层、富水砂层、软塑或流塑性地层等不良地质中盾构带压开仓具有重要指导意义。     

The effect of weld residual stress on fracture toughness at the intersection of two welding lines of offshore tubular structure

Due to the spatial complexity and fabrication characteristics of offshore platforms, it is inevitable to encounter overlaps or proximity of weld lines in tubular joints. Several international standards such as American Petroleum Institute (API), American Welding Society (AWS), and American Institute of Steel Construction (AISC) regulate the minimum distance between primary weld beads; however, any logical and detailed background of this limitation has not been presented. For a non-compliant weld joint where the regulation is not met, fracture toughness calculation is a typical index to verify the structural integrity.This research consists of two parts. First, weld residual stress distributions are calculated by a 3D thermo-mechanical nonlinear Finite Element Analysis. Two crossing welds, a T-weld crossing on a butt weld, are simulated in one model. A separate tee and a butt welding simulations are also performed for a comparative purpose. Second, SIFs and J-integral values are calculated at the surface and deepest crack tip locations for four different types of semi-elliptical surface cracks. Four cracks are embedded into the weld model and the residual stress distribution from the 3D thermo-mechanical FEA are mapped to a 3D FE crack model as initial conditions. An additional axial tensile load is also imposed. SIF values are compared with those using the weighting function method for the butt weld model subject to three load cases, i.e., tensile stress only, weld residual stress only, and both of them. From the simulation, a tubular joint containing a chord girth weld intersected with weld beads of brace is found to show lower the SIF values than that having only a girth weld on chord.