渗透球壳流固耦合问题的位移及内力解

在弹性薄壳的线性(非线性)理论和流体力学基本方程的基础上,在小雷诺数的情况下应用相容欧拉-拉格朗日法建立了渗透球壳在流体中流固耦合的基本方程及关系式,并通过摄动法求解了渗透球壳在粘性流体中的流函数从而进一步解出其位移及内力解.通过具体算例,给出了壳的位移变形及内力图,并对有关参数进行讨论,绘出相关曲线.得出渗透系数k和流速越大的情况下,壳体位移也就越大,相应的内力也变大;球壳在三个角度处位移为零.文章能为过滤器问题提供指导.     

航站楼内部通信系统在铁路客运站应用的初探

本文介绍了航站楼内部通信系统的概念及特点，对内部通信系统的性能、功能、终端和接口等多个方面进行了详细的阐述，并对内部通信系统在铁路客运站的应用进行了展望。     

既有线车辆用车轴轮座上裂纹扩展性评价

介绍在既有线车辆轮座部位加工深度不等的人工伤痕,实施疲劳试验,并进行裂纹扩展性评价的结果.     

A novel fuzzy logic correctional algorithm for traction control systems on uneven low-friction road conditions

The traction control system (TCS) might prevent excessive skid of the driving wheels so as to enhance the driving performance and direction stability of the vehicle. But if driven on an uneven low-friction road, the vehicle body often vibrates severely due to the drastic fluctuations of driving wheels, and then the vehicle comfort might be reduced greatly. The vibrations could be hardly removed with traditional drive-slip control logic of the TCS. In this paper, a novel fuzzy logic controller has been brought forward, in which the vibration signals of the driving wheels are adopted as new controlled variables, and then the engine torque and the active brake pressure might be coordinately re-adjusted besides the basic logic of a traditional TCS. In the proposed controller, an adjustable engine torque and pressure compensation loop are adopted to constrain the drastic vehicle vibration. Thus, the wheel driving slips and the vibration degrees might be adjusted synchronously and effectively. The simulation results and the real vehicle tests validated that the proposed algorithm is effective and adaptable for a complicated uneven low-friction road.     

泵站厂房中吊车竖向荷载下吊车梁最大内力值及作用面的计算方法

在厂房中设有吊车来起吊大构件,运行时吊车在吊车梁上移动,对梁产生的最大内力值及作用面在变化;而吊车梁等自重产生的内力值则随截面位置的不同而变化。该文推导用公式一次即能准确计算出吊车梁的最大内力值及作用位置,以便设计吊车梁。     

Workspace analysis to generate a collision-free torch path for a ship welding robot

We propose a method to determine the optimal initial location and to generate torch paths for a ship welding robot with 6 degrees of freedom (DOF). The optimal initial location is determined using an objective function, which is set up by combining constraints on the torch posture, manipulability, and the range of each joint angle to avoid collisions. A genetic algorithm (GA) is used to optimize the objective function because it does not require additional derivatives. After the initial location is determined, torch paths are generated by interpolating the starting point, endpoints and torch postures using inverse kinematics. Our method can be applied to automate the welding job for each block during ship building, irrespective of the shape of the robots, by changing the objective function.     

电子差速系统轮胎附着特性模拟仿真研究

电子差速系统相对于传统的机械式差速器可以实现转矩的精准分配,根据轮胎的纵向运动特性以及侧向运动特性,结合轮胎滑移率让内外侧车轮在过弯时拥有足够的附着力,减小整车的横摆角速度,提高过弯稳定性。采用后轮双电机的驱动方案,驱动电机采用直接转矩控制的方法,由整车控制器将指定的计算转矩信号发送给电机控制器完成动力分配,所需转矩根据驾驶员的加速踏板及方向盘转角,运用阿克曼转向模型计算得到。     

考虑复合地基侧摩阻力作用下土中竖向应力解

为了估算新建路基对既有路基影响,以半无限体内Mindlin应力方程解为计算基础,假设复合地基为一个加固整体,对复合地基侧壁摩阻力进行积分,推导复合地基侧摩阻力在土体中引起的附加应力的解析表达式,计算在复合地基作用下距填筑坡脚处一点的土竖向附加应力。     

小净距隧道下穿薄煤层采空区地层开挖稳定性分析

采空区地层离散性大,小净距隧道近接下穿不同倾角薄煤层采空区开挖将引起采空区内腔塌陷。建立小净距隧道近接下穿采空区地层开挖模型,对比分析采空区倾角为0°、15°、25°、40°时先行洞监测面洞周位移和初支内力。结果表明:后行洞初支闭合时,采空区倾角为15°时,拱顶下沉量最大;采空区倾角为40°时,仰拱隆起量和拱腰水平收敛量最大;随着采空区倾角增大,初期支护正(内)弯矩分布和轴力最大位置有向近接采空区侧移动的趋势,偏压越严重;应力集中逐渐由右拱脚向左拱脚移动。最大偏心距出现在拱脚处,采空区倾角为15°时,偏心距最小,初期支护稳定性最好;倾角为40°时,偏心距最大,不利于初期支护稳定。     

Experimental study of the airside performance for interrupted fin-and-tube heat exchanger with hydrophilic coating under dehumidifying conditions

The airside heat transfer and friction characteristics of seven interrupted fin-and-tube heat exchangers with hydrophilic coating under dehumidifying conditions are experimented. The effects of number of tube rows, fin pitch and inlet relative humidity on airside performance are analyzed. The test results show that the influence of fin pitch on the friction characteristic under dehumidifying conditions is similar to that under dry surface, and the friction factors decrease slightly with the increase of number of tube rows. The heat transfer performance decreases as fin pitch and number of tube rows increases. The heat transfer performance and the friction characteristic are independent of inlet relative humidity. Based on the test results, heat transfer and friction correlations in terms of the Colburn j factor and Fanning f factor, are proposed to describe the airside performance of the interrupted fin geometry with hydrophilic coating under dehumidifying conditions. The correlation of the Colburn j factor gives a mean deviation of 9.7%, while the correlation of the Fanning f factor shows a mean deviation of 7.3%.