PHC桩损伤处应力释放与水平受力影响分析

基于大型有限元软件ANSYS建立单桩有限元模型,以某5万DWT高桩码头为例,计算分析PHC桩在桩基完整性检测割桩处的应力释放以及损伤对水平承载的影响。结果表明:PHC桩在割桩损伤处应力释放明显,损伤区域应力变化剧烈,损伤处应力变化规律和应力集中系数与桩的预应力水平无关;水平荷载作用时PHC桩的预应力对于提高损伤桩的抗裂效果明显,损伤处受应力集中影响,预应力水平越高损伤处应力变化越大,而且最不利应力位置也下移到损伤平台内侧处。     

Assessment of fatigue strength of steel butt-welded joints in as-welded condition – Alternative approaches for curve fitting and mean stress effect analysis

Experimental fatigue data for butt-welded joints in as-welded condition and under constant amplitude tensile loading (secondary bending included) were analyzed using the nominal stress system and the notch stress system. Two approaches were used; a standard fitting procedure and minimization of the sum of squared perpendicular distances from a line with a fixed and free slope. In all cases, the latter method gave better agreement between the experimental and predicted fatigue life and fatigue strength. The analyses showed both with all broken specimen data included and with reduced data that the FAT225 curve, as recommended by IIW, might be too optimistic for the notch stress approach in the case of butt-welded joints in as-welded condition. It was also found that use of the local stress ratio instead of the applied stress ratio might explain many issues concerning current observations and apparent inconsistencies in reported literature.     

Dynamic demand estimation and prediction for traffic urban networks adopting new data sources

Nowadays, new mobility information can be derived from advanced traffic surveillance systems that collect updated traffic measurements, both in fixed locations and over specific corridors or paths. Such recent technological developments point to challenging and promising opportunities that academics and practitioners have only partially explored so far.The paper looks at some of these opportunities within the Dynamic Demand Estimation problem (DDEP). At first, data heterogeneity, accounting for different sets of data providing a wide spatial coverage, has been investigated for the benefit of off-line demand estimation. In an attempt to mimic the current urban networks monitoring, examples of complex real case applications are being reported where route travel times and route choice probabilities from probe vehicles are exploited together with common link traffic measurements.Subsequently, on-line detection of non-recurrent conditions is being recorded, adopting a sequential approach based on an extension of the Kalman Filter theory called Local Ensemble Transformed Kalman Filter (LETKF).Both the off-line and the on-line investigations adopt a simulation approach capable of capturing the highly nonlinear dependence between the travel demand and the traffic measurements through the use of dynamic traffic assignment models. Consequently, the possibility of using collected traffic information is enhanced, thus overcoming most of the limitations of current DDEP approaches found in the literature.     

中韩船舶油污损害赔偿制度的比较

韩国不论是从地理位置还是经济贸易往来,对于我国是很重要的邻国.由于海上运输的国际性,我国的船东有在该国卷入油污损害赔偿案件的可能,研究其油污损害赔偿制度能够更好的保护我国船东的权益,而且对于我国完善油污民事赔偿立法有一定的借鉴作用.本篇论文比较了中韩油污损害赔偿制度,并对完善我国油污损害赔偿制度提出几点建议.     

埋地管道防腐层破损点检测技术综合应用研究

对防腐层完整性检测尤其是对防腐层破损点的精确定位,及对检出大、中面积破损点开挖修补,是确保土壤跟管道的有效绝缘、提高阴极保护效果的关键。文中分析了常用埋地钢质管道防腐层破损点检测技术特点,结合现场检测实践,综合应用多种技术,能有效检测埋地钢质管道防腐层破损点。根据测量数据可以判断破损点大小以及是否开挖修理,在管道安全运行及检测的经济性之间寻找结合点。     

山区漫水桥梁水毁调查分析及重建设计

重点阐述在涞水县7.21灾后公路恢复重建中，对桥梁水毁状况的调查分析以及工程重建设计要点，可为相关工作提供借鉴。     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

Design of tyre force excitation for tyre–road friction estimation

Knowledge of the current tyre–road friction coefficient is essential for future autonomous vehicles. The environmental conditions, and the tyre–road friction in particular, determine both the braking distance and the maximum cornering velocity and thus set the boundaries for the vehicle. Tyre–road friction is difficult to estimate during normal driving due to low levels of tyre force excitation. This problem can be solved by using active tyre force excitation. A torque is added to one or several wheels in the purpose of estimating the tyre–road friction coefficient. Active tyre force excitation provides the opportunity to design the tyre force excitation freely. This study investigates how the tyre force should be applied to minimise the error of the tyre–road friction estimate. The performance of different excitation strategies was found to be dependent on both tyre model choice and noise level. Furthermore, the advantage with using tyre models with more parameters decreased when noise was added to the force and slip ratio.     

基于发动机台架考核方法的气缸盖高周疲劳特性研究

依据发动机台架考核规范,运用疲劳强度理论,对某铸铁气缸盖进行高周疲劳强度评估。明确温度和应力随考核工况改变的变化行为,研究气缸盖各区域受工作载荷的影响状况,为缸盖寿命评估模型提供载荷边界。结合疲劳理论,在考虑材料修正的基础上进行了疲劳特性分析和损伤状况分析。分析表明,气缸盖各区域的疲劳安全系数均大于1,视为安全,但冷却钻孔区域的安全裕度较小。