尼铁现代化项目中矩形空心桥台的优化设计

当前常用的时速200 km的铁路矩形空心桥台参考图中的桥台截面尺寸偏厚,安全富余量很大。为节约混凝土圬工量,希望在保证安全的前提下减少桥台截面尺寸。首先提出专门针对铁路矩形空心桥台台身截面计算的荷载图示,然后利用这一新的图示对拉伊铁路项目中使用的常规矩形空心桥台进行有限元分析,经过不断试算提出最优的截面尺寸。在钢筋用量基本不变的情况下,新尺寸桥台较原参考图中桥台的混凝土用量减少10%以上。对于项目所在地尼日利亚国水泥价格高昂的情况而言,桥台尺寸的这一优化将产生较大的经济效益。     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

挂篮底模纵梁受力简化计算方法及承重分配系数

以一桥梁施工工程实例为依托,采用有限元软件ANSYS对桥梁悬臂施工中使用的菱形挂篮进行仿真分析.提出3种简化模式计算底模纵梁的承重分配,对比发现将底模纵梁承受的外荷载简化为集中荷载,并分配至挂篮下前后横梁的方法是最优简化计算方法.在此基础上对挂篮底模纵梁承重分配系数进行优化,从而简化了繁琐的挂篮底模纵梁受力分析计算,保证了挂篮结构设计和施工的安全.     

A regression and beam theory based approach for fatigue assessment of containership structures including bending and torsion contributions

Container shipping has been expanding dramatically during the last decade. Due to their special structural characteristics, such as the wide breadth and large hatch openings, horizontal bending and torsion play an important role to the fatigue safety of containerships. In this study the fatigue contributions from vertical bending, horizontal bending and torsion are investigated using full-scale measurements of strain records on two containerships. Further, these contributions are compared to results from direct calculations where a nonlinear 3D panel method is used to compute wave loads in time domain. It is concluded that both bending and torsion have significant impacts on the fatigue assessment of containerships. The stresses caused by these loads could be correctly computed by full-ship finite element analysis. However, this requires large computational effort, since for fatigue assessment purposes the FE analysis needs to be carried out for all encountered sea states and operational conditions with sufficient time steps for each condition. In this paper, a new procedure is proposed to run the structure finite element analysis under only one sea condition for only a few time steps. Then, these results are used to obtain a relationship between wave loads and structural stresses through a linear regression analysis. This relation can be further used to compute stresses for arbitrary sea states and operational conditions using the computed wave loads (bending and torsion moments) as input. Based on this proposed method for structure stress analysis, an efficient procedure is formulated and found to be in very good agreement with the full-ship finite element analysis. In addition it is several orders of magnitude more time efficient for fatigue assessment of containership structures.     

STX1(2)型驮背多功能运输车超偏载检测标准

分析了STX₁₍₂)型驮背多功能运输车对既有超偏载检测方法和标准的适应性,提出了该车的超偏载检测方案,明确了公路货车或半挂车超偏载的检测方法及评判标准。     

超大型自航抓斗挖泥船作业流程载荷分析

以大型自航抓斗挖泥船为研究对象,建立相应的水动力计算模型。主要研究抓斗挖泥作业不同阶段下船舶运动、锚泊线受力情况以及其随不同环境载荷的变化规律,为船舶安全作业提供依据。研究结果表明,船舶在抓斗旋转和卸料时最为危险,船舶横荡、横摇及各锚泊线张力受其影响很大,实际作业时应尽量保持迎浪状态,进而确保船舶作业安全。     

压载荷下骨材贯穿孔孔边应力集中模型试验

以船舶双层底结构为研究对象开展模型试验,研究板材中的开孔在承受压力载荷作用下的孔边应力分布情况,分析压力载荷下不同开孔孔型以及不同补强结构对孔边应力分布情况的影响。在此基础上,开展相关仿真分析,将试验结果与有限元仿真结果进行对比,验证有限元仿真的准确性。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

An improved cellular automaton with axis information for microscopic traffic simulation

Cellular Automaton (CA), an efficient dynamic modeling method that is widely used in traffic engineering, is newly introduced for traffic load modeling. This modeling method significantly addresses the modest traffic loads for long-span bridges. It does, however, require improvement to calculate precise load effects. This paper proposed an improved cellular automaton with axis information, defined as the Multi-axle Single-cell Cellular Automaton (MSCA), for the precise micro-simulation of random traffic loads on bridges. Four main ingredients of lattice, cells’ states, neighborhoods and transition rules are redefined in MSCA to generate microscopic vehicle sequences with detailed vehicle axle positions, user-defined cell sizes and time steps. The simulation methodology of MSCA is then proposed. Finally, MSCA is carefully calibrated and validated using site-specific WIM data. The results indicate: (1) the relative errors (REs) for the traffic parameters, such as volumes, speeds, weights, and headways, from MSCA are basically no more than ±10% of those of WIM data; (2) the load effects of three typical influence lines (ILs) with varied lengths of 50, 200 and 1000 m are also confidently comparable, both of which validate the rationality and precision of MSCA. Furthermore, the accurate vehicle parameters and gaps generated from MSCA can be applied not only for precise traffic loading on infrastructures but also for the accurate estimation of vehicle dynamics and safety. Hence, wide application of MSCA can potentially be expected.     

Towards a model of hydrodynamic damping for a circular cylinder with helical strakes at low KC

This paper investigates the hydrodynamic damping of a circular cylinder with helical strakes at Keulegan-Carpenter (KC) number from 0.07 to 3 in the presence of steady currents. Experiments were performed with a straked cylinder oscillating in either in-line or cross currents over Reynolds number (based on the oscillating velocity amplitude) varying from 1260 to 54,000. With in-line current being present, the measured drag coefficients of the straked cylinder are found to depend on the ratio between the oscillating velocity amplitude and the steady current velocity. This phenomenon is further confirmed by computational fluid dynamics using large-eddy simulations. The drag coefficients obtained from the numerical simulations agree well with the experimentally determined values. Similar phenomenon is observed for the cases with cross background current. Based on the experimental data, empirical formulae are proposed to evaluate drag coefficients. These results are of importance in estimating the resonant motion and the fatigue life of risers, e.g. water intake risers, in the flow regime of low KC. Finally, recommendations are provided for fatigue analysis of risers with helical strakes from the perspective of engineering practice.