确定焊接反变形的数值模拟及规律分析

焊接接头附近局部的加热及冷却使被焊结构产生残余应力及角变形.目前在船厂精度控制中,通常采用构件焊接后对某些部位进行火工校正的方法来控制残余角变形.文章提供了另外一种有效控制结构残余角变形的方法:对结构焊前施加弹性的反向变形.利用热弹塑性有限元法来模拟结构的焊接过程,并对不同板厚、不同热源的结构分别进行数值模拟,最终确定焊接结构的弹性反变形规律:焊接前施加弹性反变形的结构在焊接后角变形趋于零.     

地铁直流牵引供电系统框架泄漏保护的优化设计

介绍了地铁直流牵引供电系统框架泄漏保护的优化设计方案.通过对牵引变电所整流器独立设置一套框架泄漏保护装置,可以缩小整流器故障时框架泄漏保护动作的影响范围,提高直流牵引供电系统运行的可靠性和灵活性.     

3-D numerical and experimental analysis for airflow within a passenger compartment

People use cars so frequently that they always consider the air-conditioning, and thermal comfort of the driver and passenger when buying a new car. Therefore accurate simulation of the thermal performance of automobile air conditioners to improve human comfort has become increasingly important. In order to improve the thermal comfort of passengers, 3-D flow motion and thermal behavior within vehicles must be analyzed. In this paper, a numerical simulation was used to investigate thermal behavior in a vehicle. Because air temperature at an air vent is related to the cooling capacity of the air conditioner, the cooling capacity was calculated using ɛ-NTU (effective number of transfer unit) theoretical equations. Using the air temperature relationship between inlet and outlet vents as boundary conditions, a 3-D unsteady κ-ɛ turbulent model was used to give a transient analysis simulation of the temperature field and flow conditions in a vehicle’s passenger cabin. Cooling cycle analysis and conjugate heat transfer analysis at the inside surface of the cabin’s ceiling, floor and sides were also considered. The predicted temperature distributions in the vehicles passenger cabin were in good agreement with those obtained experimentally.     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.     

承台大体积混凝土水化热分析与施工控制

结合援孟加拉国中孟友谊六桥主桥承台设计与施工,利用Midas/Civil有限元计算分析软件对承台大体积混凝土水化热进行仿真分析,掌握水化热变化规律及其应力影响,据此指导现场施工控制。结果表明:仿真分析很好地反映了水化热变化规律及其应力影响,混凝土质量优良,没有出现温度裂缝,可供类似大体积混凝土设计与施工借鉴。     

沥青混合料搅拌设备导热油炉的选择及使用

针对施工单位在选择使用沥青混合料搅拌设备导热油炉中存在的问题,提出合理选择使用导热油炉。     

基于有机朗肯循环的车用柴油机排气余热回收系统性能分析

利用设计的有机朗肯循环系统回收某重型车用柴油机的排气能量,通过台架试验,获得了变工况下柴油机排气余热能分布特性。分析了有机工质蒸发压力、过热度以及柴油机工况变化对有机朗肯循环系统性能的影响,以系统净输出功率和热效率为优化目标,确定了适用于有机朗肯循环系统的最佳蒸发压力。研究结果表明,当有机工质蒸发压力为1.8 MPa时,有机朗肯循环系统的净输出功率最大可以达到12.69kW,热效率可以达到11.19%;将有机工质加热至过热状态并不能明显提高有机朗肯循环系统的净输出功率。     

多次喷射对柴油机燃烧与排放影响的试验研究

基于1台高压共轨涡轮增压柴油机,采用不同的预喷正时、预喷油量与后喷正时等,研究了多次喷射对燃烧放热、排放生成与燃油经济性的影响,以实现均质压燃和低温燃烧过程。研究结果表明:随预喷正时提前,缸内峰值压力降低,主燃阶段的滞燃期缩短,NOx和炭烟排放均降低;随预喷油量增加,预喷阶段燃烧的放热率和最大压力升高率增大,NOx和HC排放增大,而PM和CO排放降低;随后喷始点推迟,缸内压力与主放热率峰值差异变小,NOx排放降低,但炭烟排放先增大后逐渐降低。     

基于流固耦合模型的负压式EGR阀传热研究

采用CFD方法,建立了由阀体和阀体内的流体组成的负压式EGR阀的流固耦合传热仿真模型,进行了流体与固体之间的共轭传热仿真。仿真及试验结果表明,在上阀体设计冷却水道,有助于改善阀体的换热状况,能很好地满足安装在上阀体的密封环以及其他附件工作温度要求。     

地铁杂散电流防护体系研究

通过对地铁直流供电系统杂散电流的形成、危害及传统排流法防护体系的分析,针对排流法防护体系中存在的问题,提出了新型的泄漏电缆 等电位连接法防护改进体系。