At-sea towing of a Mega-Float unit

A huge floating offshore platform (359m long, 60m wide, and 3m deep) was towed into the Pacific Ocean for a validation experiment for a floating airport. Full-scale measurements of towline tension and the bending strain on the upper-deck were made during towing. The measured bending moment agreed well with numerical calculation without taking the draught and towing speed into consideration.     

Stress intensity factor measurement of cracks using piezoelectric element

A stress intensity factor (SIF) measurement method for cracks using a piezoelectric element and an electrostatic voltmeter is presented. In this method, an isotropic piezoelectric element is first attached near the tip of the crack. Then surface electrodes are attached to three different positions on the piezoelectric element. The electric potentials of the surface electrodes, which are proportional to the sum of the stress ( _x + _y ) on the structural member, are measured by an electrostatic voltmeter during load cycling. The mode I and mode II SIFs of the crack are estimated using the relationship between the SIF and ( _x + _y ). The applicability of the proposed method is examined through experiments and numerical analysis.     

砂卵石地层台阶法施工隧道围岩-支护结构应力应变特性三维离散元分析

为了解砂卵石地层隧道围岩和支护结构的应力应变特性，以青海循隆高速公伯峡隧道为依托，借助PFC3D离散元软件对公伯峡隧道穿越砂卵石地层进行三维模拟，重点研究以密排短管棚预支护为根本前提，以三台阶预留核心土为施工方法的砂卵石地层围岩和支护结构的应力应变特性，并与现场实测进行对比分析。研究结果表明： 隧道台阶开挖时，围岩应力集中范围逐渐从拱顶过渡到拱腰，直到拱脚，对应的塑性区范围不断扩大，且密排短管棚对塑性区的发展有一定的“遮拦效应”； 围岩横纵向变形规律一致，主要是向隧道临空面产生收敛变形，且密排短管棚形成的梁拱效应限制了掌子面前方位移发展； 2种方法得到的初期支护变形规律一致，均呈阶段性变化，拱顶下沉累计值大于周边收敛累计值，且两者的最终变形量均满足规范限值要求。     

磁测式船舶姿态自动测量装置研究

利用三维磁传感器直接敏感在同状态下两个不同坐标系中的船舶综合磁场三维磁感应强度,研制了出一种新型的船舶姿态实时测量系统,并对该系统的测量原理,误差分析,校正原理与方法等作了较全面的论述。     

沥青混凝土热铺层厚度测量仪设计

针对在公路养护与沥青混凝土路面摊铺过程中,沥青混凝土的厚度控制对施工成本、路面平整度、路面质量及验收结果的影响,设计了一种能够精确测量沥青混凝土热铺层厚度的实用新型厚度测量仪,克服了目前公路工程施工中沥青混凝土热铺层厚度测量技术中的缺点与不足     

罗兰C TOA-ASF测量系统设计与实现

附加二次相位因子（ASF）是影响罗兰C导航/授时系统精度的主要因素。进行ASF修正主要有理论预测法和实测法两种。针对罗兰C到达时间ASF实测修正的需要,本文给出了ASF测量系统的测量原理和测量系统组成,详细介绍了测量系统的设置、软硬件设计。车载试验表明,该测量系统的设计是成功的,能够满足ASF实测的需要。     

偏压隧道处治措施及稳定性分析

以上瑞高速公路怀新段第8合同段青山冲隧道为工程实例,针对左线出口端洞口浅埋偏压情况,为了节约工程投资,实施了反压回填的处治方案,采用数值模拟分析及现场监控量测数据分析了偏压隧道支护结构的受力状态和稳定性,可供类似工程参考。     

An ABS control logic based on wheel force measurement

The paper presents an anti-lock braking system (ABS) control logic based on the measurement of the longitudinal forces at the hub bearings. The availability of force information allows to design a logic that does not rely on the estimation of the tyre–road friction coefficient, since it continuously tries to exploit the maximum longitudinal tyre force.

The logic is designed by means of computer simulation and then tested on a specific hardware in the loop test bench: the experimental results confirm that measured wheel force can lead to a significant improvement of the ABS performances in terms of stopping distance also in the presence of road with variable friction coefficient.     

人工关节磨损测量方法综述

人工关节的磨损问题是制约我国人工关节矫形术全面开展的重要因素之一，而磨损的检测和分析技术是评价磨损的手段。随着新技术、新材料等的发展，对人工关节磨损的检测提出新的要求，其中越来越迫切需要精确实现人工关节微量磨损的数字化检测、分析和表征。文章论述了目前国内外主要测量方法，分析了各自的特点和优点，这对于人工关节磨损的测量及其研究具有参考价值。     

离焦对光测影响的初步研究

分析离焦产生机理,并通过实验的方法,定量地分析离焦对光测的影响.有助于解决在进行大视场测量时,特别是对大视场内的运动目标位置进行测昔时,在什么位置标定既方便又不影响测量精度的难题.