低同步串级调速系统转差功率反馈方式的研究

绕线式异步电机转差功率反馈到电网进行调速的方法已在许多工业部门得到广泛应用,但由于调速过程中转子电势将低于电网电压,因而这种调速方式需要在电网与逆变器之间接入一个升压变压器。本文提出了一种省去升压变压器和直接将转差功率反馈到定子绕组的新的串级调速方法。文中对定子绕组反馈点的选择、等效电路数模及主要参数作了分析,并在一台改制的绕线式异步电机上作了试验,结果表明这种调速方法除经济简便外,仍具有优良的调速性能。     

汽车防抱死制动系统H_∞控制与PID控制的比较研究

控制方法是汽车防抱死制动系统的核心技术。为了提高ABS系统的鲁棒性能,在建立汽车防抱死制动系统数学模型的基础上,设计了H∞控制器,在Matlab/Simulink平台上对基于H∞控制器的ABS系统进行了动态仿真,并与基于传统PID控制器的ABS系统进行对比。通过对仿真结果进行比较发现,PID控制和H∞控制都能使ABS系统获得较好的制动性能;H∞控制响应迅速、具有优秀的稳定性和鲁棒性,总体控制效果优于PID控制。     

The dynamic study of locomotives under saturated adhesion

In order to study the dynamic behaviours of locomotives under saturated adhesion, the stability and characteristics of stick–slip vibration are analysed using the concepts of mean and dynamic slip rates. The longitudinal vibration phenomenon of the wheelset when stick–slip occurs is put forward and its formation mechanism is made clear innovatively. The stick–slip vibration is a dynamic process between the stick and the slip states. The decreasing of mean and dynamic slip rates is conducive to its stability, which depends on the W/R adhesion damping. The torsion vibration of the driving system and the longitudinal vibration of the wheelset are coupled through the longitudinal tangential force when the wheelset alternates between the stick and the slip states. The longitudinal oscillation frequencies of the wheelset are integral multiples of the natural frequency of torsion vibration of the driving system. A train dynamic model integrated with an electromechanical and a control system is established to simulate the stick–slip vibration phenomenon under saturated adhesion to verify the theoretical analysis. The results show that increases of the longitudinal axle guidance stiffness and the motor suspension stiffness are beneficial to the stick–slip vibration stability and the locomotive's traction ability. The optimised matching of the longitudinal axle guidance stiffness and the motor suspension stiffness are helpful to avoid longitudinal resonance when the stick–slip vibration occurs.     

An investigation of the effects of pneumatic actuator design on slip control for heavy vehicles

Progress in reducing actuator delays in pneumatic brake systems is opening the door for advanced anti-lock braking algorithms to be used on heavy goods vehicles. However, little has been published on slip controllers for air-braked heavy vehicles, or the effects of slow pneumatic actuation on their design and performance. This paper introduces a sliding mode slip controller for air-braked heavy vehicles. The effects of pneumatic actuator delays and flow rates on stopping performance and air (energy) consumption are presented through vehicle simulations. Finally, the simulations are validated with experiments using a hardware-in-the-loop rig. It is shown that for each wheel, pneumatic valves with delays smaller than 3 ms and orifice diameters around 8 mm provide the best performance.     

德国滑模摊铺机连续摊铺枕式无碴轨道轨下基础施工技术

介绍德国铁路土路基上枕式 (Rheda型 )无碴轨道轨下基础采用滑模摊铺机连续摊铺混凝土底座和混凝土路槽的施工技术 ,并与我国长期施工实践所积累的较为成熟的轨排支撑架法技术相比较 ,对如何再提高机械化施工程度以及如何提高施工质量提出新的思路与方向。     

滑差对贝氏体钢轨材料磨损行为的影响

通过对磨试验研究接触应力相同时贝氏体钢轨的磨损率、表面粗糙度、硬度,并结合扫描电镜观测到的磨损表面和剖面的形貌特征,分析不同滑差条件下贝氏体钢轨的磨损行为特征和变化规律.结果表明:接触应力为500 MPa条件下,贝氏体钢轨磨损率随滑差的增大而显著增大,滑差由2%增大到10%时磨损率增大了8倍;小滑差条件下的贝氏体钢轨表面较光滑,有少量疲劳裂纹,以滚动接触疲劳磨损为主;大滑差条件下表面粗糙,有疲劳裂纹、剥落坑和表面划擦痕迹,更接近滑动磨损;增大滑差可导致磨损表面加工硬化率偏大;增大滑差对贝氏体钢轨表面的滚动接触疲劳裂纹在深度方向的扩展几乎无影响,且对塑性变形层厚度影响不明显;大滑差可引发亚表面次表层裂纹.     

侧滑仪与检测工作站通信技术研究

汽车前轮定位参数的正确与否,对汽车的行驶平顺性、安全性、秉坐的舒适性及操纵的灵巧等方面有很大影响.因此,作为前轮定位参数的重要部分--侧滑量的检测在汽车检测系统中占有不可或缺的地位.     

滑模摊铺机施工中的平整度控制

水泥混凝土路面机械施工方法中最为先进的方法就是滑模摊铺机施工法,我国的滑模摊铺施工技术起步较晚,对该项技术的掌握也不是很好。针对如何提高滑模摊铺机的使用效率、提高施工质量进行分析,对滑模摊铺机的作业特点、对材料的要求以及保证平整度的措施等方面进行了探讨。     

均布荷载作用下双面组合梁的滑移效应分析

利用基本力学方法对钢．混凝土双面组合梁在均布荷载作用下的滑移效应进行分析，推导得到了负弯矩区上、下交界面滑移沿梁长方向的表达式，并通过算例比较了双面组合梁与传统单面连续组合梁的滑移特点。计算表明，与传统单面连续组合梁相比，钢-混凝土双面组合连续梁不仅在负弯矩区提高了截面承载力，也使截面刚度得到了提高。     

某高速公路桥梁拓宽后伸缩缝锚固区混凝土破坏原因分析

结合九乡河大桥扩建工程,探讨了桥台处伸缩缝锚固区混凝土的有限元建模方法,着重研究了桥台处伸缩缝锚固区混凝土的破坏成因。分析表明,伸缩缝锚固区开裂的主要原因是新旧桥台的不均匀沉降,采用文中提供的建模方法,可以正确地模拟伸缩缝处混凝土的破坏,从而明确破坏机理,并为此类旧桥加宽工程的设计和施工提供借鉴。