相继增压系统对改善船用直列八缸发动机性能的试验研究

随着大型柴油发动机经济性和排放要求的不断提升,以及对发动机稳态、瞬态特性要求的不断提高,传统的涡轮增压系统已无法满足船用发动机全工况性能的要求。为了提高产品竞争力和适配性,针对某8缸直列船用柴油发动机开发了带有定压排气管的相继增压系统,并进行了发动机台架试验研究。结果表明：发动机中、低转速时,相继增压系统使发动机比油耗可以下降5%-10%,排气温度降低30%-45%,烟度下降55%-60%；最大扭矩可以提升15.1%-36.4%；发动机最大扭矩转速工况突加突卸响应性提升约28%-29%；相继增压系统中定压排气管的设计使得发动机高工况性能也有所提升,从而实现发动机全工况性能的提升。     

压载荷下骨材贯穿孔孔边应力集中模型试验

以船舶双层底结构为研究对象开展模型试验,研究板材中的开孔在承受压力载荷作用下的孔边应力分布情况,分析压力载荷下不同开孔孔型以及不同补强结构对孔边应力分布情况的影响。在此基础上,开展相关仿真分析,将试验结果与有限元仿真结果进行对比,验证有限元仿真的准确性。     

5000 PCC“SHANGHAI HIGHWY”船主机启动分析与处理

分析5 000 PCC"SHANGHAI HIGHWAY"船主机伺服油压低引起主机启动故障的原因、介绍调查与处理过程,在实施了恰当的处理方法后,解决了问题。以期为类似问题的处理与解决提供借鉴和参考。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

Planning hierarchical urban transit systems for reductions in greenhouse gas emissions

Public transit systems with high occupancy can reduce greenhouse gas (GHG) emissions relative to low-occupancy transportation modes, but current transit systems have not been designed to reduce environmental impacts. This motivates the study of the benefits of design and operational approaches for reducing the environmental impacts of transit systems. For example, transit agencies may replace level-of-service (LOS) by vehicle miles traveled (VMT) as a criterion in evaluating design and operational changes. In previous work, we explored the unintended consequences of lowering transit LOS on emissions in a single-technology transit system. Herein, we extend the analysis to account for a more realistic case: a transit system with a hierarchical structure (trunk and feeder lines) providing service to a city where demand is elastic. By considering the interactions between the trunk and the feeder systems, we provide a quantitative basis for designing and operating integrated urban transit systems that can reduce GHG emissions and societal costs. We find that highly elastic transit demand may cancel emission reduction potentials resulting from lowering LOS, due to demand shifts to lower occupancy vehicles. However, for mass transit modes, these potentials are still significant. Transit networks with buses, bus rapid transit or light rail as trunk modes should be designed and operated near the cost-optimal point when the demand is highly elastic, while this is not required for metro. We find that the potential for unintended consequences increases with the size of the city. Our results are robust to uncertainties in the costs and emissions parameters.     

柴油机排气污染物PM和NOx催化处理反应平台设计与应用

使用自行设计的程序温控的催化反应平台和模拟配气系统相连接,测试并获得催化剂的催化还原NOx和催化氧化PM的准确的催化性能数据.使用该催化反应平台和常柴CZ2102型柴油机实验平台相连接,获得在稀燃条件下介孔镧铈锆铝复合氧化物对PM和NOx的催化处理实验的应用数据.为同时去除柴油机排气污染物PM颗粒和NOx的工程应用打下坚实的基础.     

全海深双球连接耐压舱的结构设计探索

钛合金耐压球壳被广泛地应用于大深度载人潜水器.但是,由于受到材料强度的限制,若采用成熟的Ti-6Al-4VELI来设计3人型的全海深载人舱,其壁厚将超出很多国家的现有制造能力.为了解决这一矛盾,该文提出了一种新的双球连接的方案,并以中国船级社最新的强度标准作为优化约束条件,用有限元分析法对这种结构形式进行了优化设计.最后,对双球结构方案与传统单球方案作了比较.     

Airline energy efficiency measures using the Virtual Frontier Network RAM with weak disposability

In this paper, airline energy efficiency is divided into three stages: the operations stage, the services stage and the sales stage. Greenhouse gas emissions are treated as an undesirable output of the services stage. This new three-stage strategic operating framework is a modification of existing models. A new model, Virtual Frontier Network Range Adjusted Measure with weak disposability, is proposed to evaluate the efficiencies of 22 international airlines, from 2008 to 2012. The results show that the new model can establish more reasonable rankings and confirm new benchmarking airlines and that inclusion in the European Union’s Emissions Trading Scheme has had little influence on the improvement of airline energy efficiency.     

带卸荷板的方块码头墙身位移对墙后土压力的影响

土压力与挡土墙体的位移密切相关,现行规范中采用主动土压力理论计算带卸荷板的方块码头墙后土压力是不完全准确的。根据此类码头结构特点,对地基条件好、基床厚度薄的方块码头墙身位移特性进行论述,对规范方法提出修正意见。依托于某工程实例,采用数值分析方法对码头墙身位移和墙后土压力进行模拟,并与规范公式计算结果进行对比,得出墙底处修正系数可取1.84,卸荷板处可取1.34,可为类似特点的工程土压力计算提供参考。     

铁路路基动态变形模量的数值模拟分析

介绍铁路路基动态变形模量理论计算公式的推导及动态变形模量的测试原理,采用有限元软件模拟动态变形模量的测试过程,分析承载板与土体接触压力、路基动态变形模量的影响因素,并计算动态变形模量的有效测试深度.结果表明:在承载板中心一定范围内,接触压力模拟结果较理论计算值大;土体的动弹性模量对接触压力影响很小,可以忽略;路基动态变形模量测试冲击荷载作用下,土体只发生弹性变形;动态变形模量与土体动弹性模量呈线性关系,路基动态变形模量的模拟结果大于理论计算值;土体的泊松比对动态变形模量影响较小;动态变形模量有效测试深度建议取0.5~0.6 m.