支线集装箱船整船强度和疲劳有限元分析

在分析UR S11A和S34生效后的集装箱船整船屈服、屈曲要求的基础上,以1艘支线集装箱船为对象,计算得到目标船整船结构各个计算工况下的应力分布,完成整船屈服、屈曲强度评估和疲劳筛选及评估,分析发现支线集装箱船艏、艉非货舱区域结构和货舱区域的横向结构,以及整船重点区域的疲劳问题不容忽视。在设计时,对上述区域结构应重点关注,必要时建议选择装载手册中最危险的工况开展整船屈服、屈曲和疲劳评估并作适当加强。     

大型集装箱船整船有限元分析计算技术研究

本文在研究大型集装箱船整船分析的基础上,总结研究和发展了二种集装箱船整船有限元分析时调整节点力和惯性平衡的处理方法.对于正确地进行大型集装箱船整船结构强度直接计算具有指导作用和实用价值.同时本文提出了对集装箱船整船结构强度分析的分工况计算和应力合成技术,可应用于集装箱船的整船结构有限元计算分析.     

船用电器柜抗冲击设计研究

为增强船内部电器柜的抗冲击性能,采用有限元法对船内不同安装型式的电器柜结构进行了模态和抗冲击性能仿真分析,通过对比分析得出了使用撑杆加固型式安装的电器柜能显著提高船内电器柜的抗冲击性能的结论,并确定了电器柜抗冲击优化设计方案。     

偏压连拱隧道施工方法研究

文章采川三维有限元数值模拟研究了偏压连拱隧道不同施工顺序下拱顶下沉、中墙稳定性及初期支护受力特征.研究结果表明,先开挖浅埋侧时,拱顶沉降较小,中墙在施工中的稳定安全系数较大、弯矩较小,初期支护受力较大；对于浅埋偏压连拱隧道,围岩变形及中墙在施工中的稳定性控制更为重要.所以,从有利于围岩变形、中墙稳定性控制以及中墙受力的角度出发,宜采用先开挖浅埋侧的施工方法.     

基于48000载重吨教学实习船的动力学结构优化

本文以48000载重吨教学实习船为研究对象,采用通用有限元软件MSC.Patran/Nastran进行全船频响分析.全船有限元计算条件要求极高,而一般情况下又存在各种资料的限制或实验数据的缺失,因而会使得计算精度较低.本文介绍利用基本的设计资料的条件下,从模态参与系数角度结合模态振型提出一种新的动力学结构优化思路,并进行计算分析以验证该方法的可行性与准确性,为全船有限元振动分析提供新的研究思路.     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

Analysis of cross effect on inherent deformation during the line heating process – Part 1 – Single crossed heating lines

This paper describes the effect of previous heating on inherent deformation by a subsequent heating line, more specifically, the case of two heating lines intersecting (crossing) each other. The paper has been divided into two parts. In the first part, the case of single crossed heating lines is studied in detail. The second part of the paper, discusses the case of more than one crossed heating lines. The novelty of the work lies in revealing the cross effect and how, factors such as, for example, the heating condition and the plate geometry, influence the resulting inherent deformation of crossed heating. In addition, relationships to easily get these influences are provided. The results are suitable for a wide range of heating conditions and plate thickness.     

调距桨桨叶连接螺栓过渡圆角光弹性试验研究

苛刻的空间尺寸要求和严酷的使用环境使得调距桨桨叶连接螺栓设计极为重要,为研究连接螺栓螺帽螺杆圆角过渡区域因截面形状突变存在的应力集中情况和应力分布规律,以某型调距桨桨叶连接螺栓联接组件作为试验模型,采用光弹性试验方法测得其应力分布和应力集中系数,并与有限元仿真分析结果进行了对比验证,为桨叶连接螺栓组件结构设计及其优化提供重要支撑。     

船舶甲板分段纵骨焊接变形和残余应力数值模拟

基于非线性分析软件Abaqus,采用顺序耦合的热弹塑性有限元方法研究典型船舶甲板分段纵骨焊接的变形与残余应力问题。焊接过程中的温度场分析采用具有截面积分shell单元的shell/solid模型,移动热源为高斯分布与均匀体组合热源,材料考虑应变随温度变化的特性。通过与T型接头焊接实验结果对比,验证了方法的可靠性。在此基础上,计算分析了甲板分段纵骨焊接的整体变形和局部板格变形,并讨论了外板纵向和横向焊接残余应力分布规律。     

基于Femap的风帆基座局部强度分析

以上海海事大学教学实习船"育明"轮为对象,研究船舶加装风帆装置的船体结构强度问题,通过局部加强风帆基座和船体连接部分来保证风帆安装部位的结构稳定性。利用Solidworks和Femap软件建立了风帆基座和船体的有限元模型,计算得到该模型在10级风载荷下受风角度从0°~60°的应力和应变。最终结果表明,在10级风载荷下,该船风帆基座和局部加强后的船体的强度符合要求。