基于FPGA的里程轮信号优选算法设计

文中通过对里程信号产生机理进行分析,提出了一种基于FPGA架构的里程优选算法,给出了实现算法的硬件架构图,并设计相应硬件电路和模拟实验。结果表明:该算法可以对3个里程轮脉冲信号进行优选采集,当里程轮处于超速或者停转状态时也能输出正确的脉冲信号。     

Research on the pipeline walking caused by cyclic increasing soil friction for free deep-sea submarine pipelines laid on even seabed

Pipelines are important to offshore oil and gas development, but suffers from the pipeline walking phenomenon due to cyclic temperature variations—where large axial walking distances threaten the safety of pipeline systems. Current research indicates that pipeline walking is triggered by steel catenary riser (SCR) tension, seabed slopes, or thermal transients. This paper proposes a new driving mechanism for the pipeline walking phenomenon, involving cyclic hardening soil strength. The finite element analysis method was adopted to analyse the soil friction difference induced walking phenomenon, and the influence of key parameters on the gain in soil friction on walking distance was studied. Pipeline walking distances under different drainage conditions in the heating and cooling processes were also calculated, and the impact of the degree of drainage in the heating process was determined. To better understand the new pipeline walking mechanism, theoretical analysis of the walking behaviour under different cyclic soil friction conditions was carried out. Analytical solutions for estimating the pipeline walking distance were also provided, based on the simplified theoretical analysis.     

潜艇均衡系统自流注水调节阀稳态噪声试验研究

本文模拟建立了潜艇均衡系统自流注水试验系统,对不同假海压力、不同系统流量、不同出口背压及串联2台调节阀时自流注水稳定过程振动噪声进行研究。结果表明:潜艇均衡注水振动噪声随着假海深度的增大而增大;空气噪声随流量调节阀开度的增大而增大,在流量调节阀开度为60°-70°之间,振动加速度及水动力噪声产生峰值;在出口背压为0-0.5 MPa之间时,振动噪声值均大于无背压状态,峰值为0.2 MPa;串联2台流量调节阀可大幅降低自流注水振动噪声。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

海上大直径超长HDPE管段沉放工艺

HDPE管段的沉放工艺直接影响管段水下对接的效率以及成功率,是HDPE管段水下安装工程中的重要环节。针对大直径超长HDPE管段的灌水沉放工艺进行系统研究,将理论分析与现场试验相结合,首次提出采用气囊配合"牺牲绳"控制管段灌水沉放的方法,并得出确定气囊数量的方法与原则,进而提出满足变水深条件下的大直径超长HDPE管的灌水沉放工艺。该工艺已成功应用于沙特吉赞JIGCC取排水工程大直径超长HDPE管段安装工程中,为今后类似工程的建设提供参考。     

潜艇舷间舾装的精度分配

[目的]潜艇建造是一个多工序耦合的工艺过程,随着模块化建造模式的发展,广义的“舾装”包含了材料成型、结构建造、设备管系制造安装及涂装等全流程,在设计阶段开展潜艇舾装的精度分配顶层规划,可有效影响潜艇建造工艺过程,确保潜艇总体性能。[方法]针对潜艇舷间舾装,首先提出精度分配的流程,然后对基于尺寸链的精度分配方法的内涵及其适用范围进行探讨,最后对舷间的关键项目及其精度控制对象进行识别,依据尺寸链原理方法对舾装全流程的未知精度项进行分配。[结果]得到了可满足建造精度需求的舷间舾装关键项目中未知精度项的分配值。[结论]通过研究,形成了包含材料、结构、设备、安装等广义舾装过程的精度分配流程及方法,并可用于指导潜艇舾装的各工艺环节和工艺设计。     

Mode jumping in the lateral buckling of subsea pipelines

Unburied subsea pipelines under high-temperature conditions tend to relieve their axial compressive stress by forming localised lateral buckles. This phenomenon is traditionally studied under the assumption of a specific lateral deflection profile (mode) consisting of a fixed number of lobes. We study lateral thermal buckling as a genuinely localised buckling phenomenon by applying homoclinic (‘flat’) boundary conditions. By not having to assume a particular buckling mode we are in a position to study transitions between these traditional modes in typical loading sequences. For the lateral resistance we take a realistic nonlinear pipe-soil interaction model for partially embedded pipelines. We find that for soils with appreciable breakout resistance, i.e., nonmonotonicity of the lateral resistance characteristic, sudden jumps between modes may occur. We consider both symmetric and antisymmetric solutions. The latter turn out to require much higher temperature differences between pipe and environment for the jumps to be induced. We carry out a parameter study on the effect of various pipe-soil interaction parameters on this mode jumping. Away from the jumps post-buckling solutions are reasonably well described by the traditional modes whose analytical expressions may be used during preliminary design.     

地面注汽管线表面散热损失影响因素分析

文中采用Fluent模拟与理论计算结合比较的方法,研究了不同因素对蒸汽管道散热损失的影响规律,并分析了理论计算模型的相对误差。发现增加注汽管线距地面高度,对其散热损失影响较弱;空气温度升高,注汽管道表面散热损失降低;风速和表面发射率对注汽管线表面热损失影响较大;数值模拟结果与理论计算数据相对误差较大。     

潜艇耐压舱室过渡段结构型式的探讨

为了探讨潜艇不同直径的耐压舱室过渡段结构型式的最优设计,利用工程计算方法和有限元方法,分析过渡段结构的应力集中,提出了能够使不同直径圆柱壳光滑过渡的结构形式--双圆弧式过渡形式.计算结果表明:双圆弧式的过渡形式能使不同直径圆柱壳两端连接处消除应力集中和改善过渡段应力分布.     

汕头市苏埃通道工程海域段平纵横方案研究

为有效解决汕头市苏埃通道工程遇到的海底硬岩、孤石群及高烈度抗震等技术难题,从海底隧道横断面、平面及纵断面方案进行研究。主要研究和结论如下： 1）对两管方案与三管方案进行比较,在海底硬岩处理方面,2种方案施工风险无本质区别,但两管方案可利用车道板下空间解决消防防灾问题、取消隧道联络通道设置、降低施工及抗震风险,优于三管方案; 2）从抗震、工程造价、结构受力及隧道运维等方面进行研究,发现盾构管片采用单层预制结构优于管片内置二次衬砌结构; 3）隧道平面方案需摸清海底硬岩及孤石群分布范围,结合码头、港池及锚地等控制因素综合确定; 4）隧道纵断面方案的确定,需充分考虑海底硬岩、孤石分布规律以及最小覆土、主航道规划标高、港池范围等控制因素,避开硬岩及孤石群,以减小隧道修建难度和风险。