A simple formulation for predicting the ultimate strength of ships

The aim of this study is to derive a simple analytical formula for predicting the ultimate collapse strength of a single- and double-hull ship under a vertical bending moment, and also to characterize the accuracy and applicability for earlier approximate formulations. It is known that a ship hull will reach the overall collapse state if both collapse of the compression flange and yielding of the tension flange occur. Side shells in the vicinity of the compression and the tension flanges will often fail also, but the material around the final neutral axis will remain in the elastic state. Based on this observation, a credible distribution of longitudinal stresses around the hull section at the overall collapse state is assumed, and an explicit analytical equation for calculating the hull ultimate strength is obtained. A comparison between the derived formula and existing expressions is made for largescale box girder models, a one-third-scale frigate hull model, and full-scale ship hulls.List of symbols A _B total sectional area of outer bottom - A _B total sectional area of inner bottom - A _D total sectional area of deck - A _S half-sectional area of all sides (including longitudinal bulkheads and inner sides) - a _s sectional area of a longitudinal stiffener with effective plating - b breadth of plate between longitudinal stiffeners - D hull depth - D _B height of double bottom - E Young's modulus - g neutral axis position above the base line in the sagging condition or below the deck in the hogging condition - H depth of hull section in linear elastic state - I _s moment of inertia of a longitudinal stiffener with effective plating - l length of a longitudinal stiffener between transverse beams - M _E elastic bending moment - M _p fully plastic bending moment of hull section - M _u ultimate bending moment capacity of hull section - M _uh ,M _us ultimate bending moment in hogging or sagging conditions - r radius of gyration of a longitudinal stiffener with effective plating [=(I _s /a _s )^1/2] - t plate thickness - Z elastic section modulus at the compression flange - Z _B ,Z _D elastic section modulus at bottom or deck - slenderness ratio of plate between stiffeners [= (b/t)(_y/E)^1/2] - slenderness ratio of a longitudinal stiffener with effective plating [=(l/r)(_y/E)^1/2] - _y yield strength of the material - _yB , _yB , _yD yield strength of outer bottom, inner bottom - _yS deck, or side - _u ultimate buckling strength of the compression flange - _uB , _uB , _uD ultimate buckling strength of outer bottom - _uS inner bottom, deck, or side     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.     

Dynamic modeling of the electro-mechanical configuration of the Toyota Hybrid System series/parallel power train

The hybridization of the conventional thermal vehicles nowadays constitutes a paramount importance for car manufacturers, facing the challenge of minimizing the consumption of the road transport. Although hybrid power train technologies did not converge towards a single solution, series/parallel power trains with power-split electromechanical transmissions prove to be the most promising hybrid technology. In fact, these power trains show maximum power train overall efficiency and maximum fuel reduction in almost all driving conditions compared to the conventional and other hybrid power trains. This paper addresses the model and design of the electro-mechanical configuration of one of the most effective HEV power trains: case study of the 2nd generation Prius. It presents the simulation work of the overall operation of the Toyota Hybrid System (THS-II) of the Prius, and explores not only its power-split eCVT innovative transmission system but also its overall supervision controller for energy management. The kinematic and dynamic behaviors of the THS-II power train are explained based on the power-split aspect of its transmission through a planetary gear train. Then, the possible regular driving functionalities that result from its eCVT operation and the energy flow within its power train are outlined. A feed-forward dynamic model of the studied power train is next proposed, supervised by a rule-based engineering intuition controller. The energy consumption of the THS-II proposed model has been validated by comparing simulation results to published results on European, American and Japanese regulatory driving cycles.     

Optimized energy management control for the Toyota Hybrid System using dynamic programming on a predicted route with short computation time

Among the general problematic of the HEV power trains, the most critical point is the determination of the power-split ratio between the mechanical and the electrical paths, known as the energy management strategy (EMS). Many EMS are proposed in the literature, and can be grouped in two categories: the local optimization EMS and the global optimization EMS. The local optimization category corresponds to the EMS based on human expertise and the knowledge of the power train components efficiency maps. Thus, the local optimization EMS manages the power train operations by referring to predefined rules. The drawback of such strategies is that it brings an instantaneous fuel consumption optimization, and does not fully optimize the fuel consumption over the whole trip. Therefore, additional fuel savings are still possible. This paper presents an overall optimized predictive EMS for the Toyota Hybrid System (THS-II) power train of the Prius. The proposed EMS is based on Dynamic Programming (DP), where the prior knowledge of the route is required in order to predetermine the power-split ratio and optimize the fuel consumption for the whole predicted route. The DP EMS proposed for the THS-II power train is designed with a very short computation time, intended to be implemented in real-time applications. The potential of this DP-controller in reducing fuel consumption on regulatory cycles are computed and compared to a rule-based controller and to the Prius published fuel consumption results. Finally, the fuel reduction enhancements of the DP-controller are computed for real road tests achieved on a MY06 Prius in Ile-de-France, by comparing to the associated observed consumption measurements.     

Jointly optimizing cost, service, and environmental performance in demand-responsive transit scheduling

In certain fleet systems, the environmental impacts of operation are, to some extent, a controllable function of vehicle routing and scheduling decisions. However, little prior work has considered environmental impacts in fleet vehicle routing and scheduling optimization, in particular, where the impacts were assessed systematically utilizing life-cycle impact assessment methodologies such as those described by the Society of Environmental Chemistry and Toxicology. Here a methodology is presented for the joint optimization of cost, service, and life-cycle environmental consequences in vehicle routing and scheduling, which we develop for a demand-responsive (paratransit or dial-a-ride) transit system. We demonstrate through simulation that, as a result of our methodology, it is possible to reduce environmental impacts substantially, while increasing operating costs and service delays only slightly.