Injection Characteristics of Palm Methyl Ester Blended with Diesel Using Zuech’s Chamber

This research attempts to characterize the injection of palm biodiesel blended with diesel in a Zuech’s chamber. Thailand conventional diesel (mandated blend of biodiesel at 5 % or B5), palm biodiesel (B100) and four other biodiesel blends ratios (B20, B40, B60 and B80) were investigated with single hole injector of 140 and 200 μm diameters, injection pressure of 40 MPa to 160 MPa, constant back pressure of 4.5 MPa and energize time of 2.5 ms. The results show that increasing biodiesel blending ratios leads to longer injection delay, larger injection pressure drop, smaller injection quantity discharge coefficient (C_d) and shorter injection duration. With increasing biodiesel blending ratio, high Cavitation number from biodiesel viscosity decreases Reynolds number. Increasing injector diameter from 140 μm to 200 μm has reduced injection delay, increased fuel injection quantity, discharge coefficient and remaining injection duration. The increasing of injection pressure were improve, injection delay, injection duration, injection quantity and discharge coefficient until injection pressure 120 MPa. In addition at injection pressure over 120 MPa are decrease injection quantity and discharge coefficient, it effect form the cavitation phenomena. Increasing of viscosity, density, Bulk modulus and sound velocity were effect to increase injection delay, with reduce injection quantity, injection duration and pressure drop during injection process.     

Load and Load Dependent Friction Identification and Compensation of Electronic Non-Circular Gear Brake System

Control of the electronic non-circular gear brake (ENGB) involves challenges, including the non-linear variation of loads and the effect of friction, which is dependent upon load. The controller must be designed based on modelling information in order to enhance control performance. This study performed model identification of the ENGB system using a DOB-based model identification method. By employing the nearest neighbor search method, the even-odd disturbance was separated without the influence of hysteresis even in situations with low control precision. The accuracy of the resulting ENGB system model was validated through experiments. The self-energizing effect due to friction between the brake disc and pad within the mechanical system was also validated.     

Numerical Analysis of the Mixture Formation in a Two-Stroke Wall-Guided LPG DI Engine for Extended-Range Electric Vehicle

The use of automotive LPG characteristics which are easy to evaporate vaporization and carry. The paper presents a design of extended-range electric vehicle for wall-guided two stroke LPG engine with direct injection combustion system. Based on the modified vehicle LPG spray model, a database describing the characteristics of vehicle LPG fuel was built and imported into the CFD software. And the accuracy of the model is verified by the Schlieren experimental results. The concentration and velocity field of the mixture in the cylinder under different load conditions are numerically analyzed. The analyzed result indicated that the start injection time θ = 60°–70°CA BTDC under part load condition, the plug electrode near the gathering of a richer mixture is easy to be fired at spark ignition time, the obvious formation of mixture in cylinder is formed and the overall air-fuel ratio is above 40: 1. The start-transition working condition and large load conditions in the piston moves upward before closing the exhaust port to start injection LPG. The optimized LPG injection start time θ ensures that the fresh gas is locked in the cylinder when the exhaust port is closed (63°CA ABDC). In the ignition time of the spark plug, an ideal homogeneous mixture in the cylinder is realized.     

Effects of Test Conditions on Fuel Economy of Gasoline-Powered Vehicle

In this study, the influence on fuel economy testing of gasoline-powered vehicles is evaluated for various test conditions (e.g., laboratory temperature, soaking time, cooling fan, battery charge state, and driving mode tracking). It showed a difference in fuel economy results of approximately 3 % between low (88 %) and high (99 %) battery state of charge conditions because the alternator saving function has a positive effect on fuel economy. Fuel economy testing with laboratory temperature changes gave a slight reduction at 21 °C and slight increase at 29 °C. The cooling fan changes had an almost negligible effect on fuel consumption. The largest fuel economy result varied by 5.2 % in the soft, standard, and rough driving conditions.     

Belief and fuzzy theories for driving behavior assessment in case of accident scenarios

The estimation of the overspeed risk before the accident is among the main goals of this paper. The proposed method uses the Energy Equivalent Speed (EES) to assess the severity of an eventual accident. However, the driver behavior evaluation should take into account the parameters related to the Driver, the Vehicle and the Environment (DVE) system. For this purpose, this paper considers a two-level strategy to predict the global risk of an event using the Dempster-Shafer Theory (DST) and the Fuzzy Theory (FT). This paper presents two methods to develop the Expert Model-based Basic Probability Assignment (EM based BPA), which is the most important task in the DST. The first one is based on the accident statistics and the second method deals with the relationship between the Fuzzy and Belief measurements. The experimental data is collected by one driver using our test vehicle and a Micro-intelligent Black Box (Micro-iBB) to collect the driving data. The sensitivity of the developed models is analysed. Our main evaluation concerns the Usage Based Insurance (UBI) applications based on the driving behavior. So, the obtained masses over the defined referential subsets in the DST are used as a score to compute the driver’s insurance premium.     

Gasket life criteria at low temperatures adopting proportional compensation for loss of flexibility and conformability

In the automobile industry, the service life of gaskets is defined as the time until which a released gasket recovers 60 % of the original compression. It was observed that the recovery curves of gaskets were highly nonlinear at high temperatures, and relatively nonlinear at temperatures above the room temperature. However, it was also noted that the recovery curves of the gaskets at temperatures below room temperature exhibited linearity with respect to the ln(time). Automotive manufacturers demand gasket life criteria that exceed a specific time or the entire life of a car. In the case of gaskets used at lower temperatures, since materials encounter losses in its flexibility and conformability, the definition of service life specifying a 60 % recovery may not be sufficiently safe to eliminate possible leakages. In this study, new gasket life criteria that could be used at low temperatures were proposed. The new criteria were proposed based on the change in Young’s modulus of the gasket material in order to conserve the sealing capability.     

Disturbance Observer-Based Sideslip Angle Control for Improving Cornering Characteristics of In-Wheel Motor Electric Vehicles

In this paper, a robust sideslip angle controller based on the direct yaw moment control (DYC) is proposed for in-wheel motor electric vehicles. Many studies have demonstrated that the DYC is one of the effective methods to improve vehicle maneuverability and stability. Previous approaches to achieve the DYC used differential braking and active steering system. Not only that, the conventional control systems were commonly dependent on the feedback of the yaw rate. In contrast to the traditional control schemes, however, this paper proposes a novel approach based on sideslip angle feedback without controlling the yaw rate. This is mainly because if the vehicle sideslip angle is controlled properly, the intended sideslip angle helps the vehicle to pass through the corner even at high speed. On the other hand, the vehicle may become unstable because of the too large sideslip caused by unexpected yaw disturbances and model uncertainties of time-varying parameters. From this aspect, disturbance observer (DOB) is employed to assure robust performance of the controller. The proposed controller was realized in CarSim model described actual electric vehicle and verified through computer simulations.     

New Optimal Power Management Strategy for Series Plug-In Hybrid Electric Vehicles

Recently Plug-in hybrid electric vehicles (PHEVs) have gained increasing attention due to their ability to reduce the fuel consumption and emissions. In this paper a new efficient power management strategy is proposed for a series PHEV. According to the battery state of charge (SOC) and vehicle power requirement, a new rule-based optimal power controller with four different operating modes is designed to improve the fuel economy of the vehicle. Furthermore, the teaching-learning based optimization (TLBO) method is employed to find the optimal engine power and battery power under the specified driving cycle while the fuel consumption is considered as the fitness function. In order to demonstrate the effectiveness of the proposed method, four different driving cycles with various numbers of driving distances for each driving cycle are selected for the simulation study. The performance of the proposed optimal power management strategy is compared with the rule-based power management method. The results verify that the proposed power management method could significantly improve the fuel economy of the series PHEV for different driving conditions.     

Effect of Hydrothermal Aging over a Commercial DOC on NO<Subscript>2</Subscript> Production and Subsequent SCR Efficiency

In this study, the effect of hydrothermal aging over a commercial diesel oxidation catalyst (DOC) on deterioration in nitrogen dioxide (NO₂) production activity has been experimentally investigated based on a micro-reactor DOC experiment. Through this experimental result, the NO₂ to nitrogen oxides (NOx) ratio at DOC outlet has been mathematically expressed as a function of DOC temperature according to various aging conditions. The current study reveals that the catalyst aging temperature is a more dominant factor than the aging duration in terms of the decrease in NO₂ production performance through DOC. The DOC sample hydrothermally aged for 25 h at 750 °C has displayed the lowest NO₂ to NOx ratio compared to the samples aged for 25 ~ 100 h at 650 °C. Also, in this study, the impact of hydrothermal aging of a DOC on the selective catalytic reduction (SCR) efficiency in a ‘DOC + SCR’ aftertreatment system was predicted by using transient SCR simulations. To validate the SCR simulation, this study has conducted a dynamometer test of a non-road heavy-duty diesel engine with employing a commercial ‘DOC + SCR’ system on the exhaust line. The current study has quantitatively estimated the effect of the variation in NO₂ to NOx ratio due to the hydrothermal aging of DOC on the NOx removal efficiency of SCR.     

Detection of Cognitive and Visual Distraction Using Radial Basis Probabilistic Neural Networks

This paper suggests a real-time method for detecting a driver’s cognitive and visual distraction using lateral driving performance measures. The algorithm adopts radial basis probabilistic neural networks (RBPNNs) to construct classification models. In this study, combinations of two driving performance data measures, including the standard deviation of lane position (SDLP) and steering wheel reversal rate (SRR), were considered as measures of distraction. Data for training and testing the RBPNN models were collected under simulated conditions in which fifteen participants drove on a highway. While driving, they were asked to complete auditory recall tasks or arrow search tasks to create cognitively or visually distracted driving periods. As a result, the best performing model could detect distraction with an average accuracy of 78.0 %, which is a relatively high accuracy in the human factors domain. The results demonstrated that the RBPNN model using SDLP and SRR could be an effective distraction detector with easy-to-obtain and inexpensive inputs.