Study of diesel spray combustion and ignition using high-pressure fuel injection and a micro-hole nozzle with a rapid compression machine: improvement of combustion using low cetane number fuel

This study aimed to reduce NO_x and soot by creating a more homogeneous lean fuel distribution in a diesel spray using high-pressure fuel injection and a micro-hole nozzle. This injection system shortened the ignition delay, but a homogeneous lean fuel distribution in the diesel spray was not achieved. Using a lower cetane number fuel, the resulting longer ignition delay made a uniform, lean fuel distribution in the diesel spray possible with this injection system. Ignition and combustion were analyzed by the combustion chamber pressure history, and flame temperatures and KL values were analyzed by the two-color method.     

Effect of operating parameters on diesel/propane dual fuel premixed compression ignition in a diesel engine

In this research, the effects of three operating parameters (Diesel injection timing, propane ratio, and exhaust gas recirculation (EGR) rates) in a diesel-propane dual fuel combustion were investigated. The characteristics of dual-fuel combustion were analyzed by engine parameters, such as emission levels (Nitrogen oxides (NO_x) and particulate matter (PM)), gross indicated thermal efficiency (GIE) and gross IMEP Coefficient of Variance (CoV). Based on the results, improving operating strategies of the four main operating points were conducted for dual-fuel PCCI combustion with restrictions on the emissions and the maximum pressure rise rate. The NOx emission was restricted to below 0.21 g/kWh in terms of the indicated specific NO_x (ISNO_x), PM was restricted to under 0.2 FSN, and the maximum pressure rise rate (MPRR) was restricted to 10 bar/deg. Dual-fuel PCI combustion can be available with low NO_x, PM emission and the maximum pressure rise rate in relatively low load condition. However, exceeding of PM and MPRR regulation was occurred in high load condition, therefore, design of optimal piston shape for early diesel injection and modification of hardware optimizing for dual-fuel combustion should be taken into consideration.     

Reduction of emissions with propane addition to a diesel engine

Recent studies on dual-fuel combustion in compression-ignition (CI) engines, also known as diesel engines, fall into two categories. In the first category are studies focused on the addition of small amounts of gaseous fuel to CI engines. In these studies, gaseous fuel is regarded as a secondary fuel and diesel fuel is regarded as the main fuel for combustion. The objectives of these studies typically involve reducing particulate matter (PM) emissions by using gaseous fuel as a partial substitution for diesel fuel. However, the addition of gaseous fuel raises the combustion temperature, which increases emissions of nitrogen oxides (NO_x). In the second category are studies focused on reactivity-controlled compression-ignition (RCCI) combustion. RCCI combustion can be implemented by early diesel injection with a large amount of low-reactivity fuel such as gasoline or gaseous fuel. Although RCCI combustion promises lower NO_x and PM emissions and higher thermal efficiency than conventional diesel combustion, it requires a higher intake pressure (usually more than 1.7 bars) to maintain a lean fuel mixture. Therefore, in this study, practical applications of dual-fuel combustion with a low air-fuel ratio (AFR), which implies a low intake pressure, were systemically evaluated using propane in a diesel engine. The characteristics of dualfuel combustion for high and low AFRs were first evaluated. The proportion of propane used for four different operating conditions was then increased to decrease emissions and to identify the optimal condition for dual-fuel combustion. Although the four operating conditions differ, the AFR was maintained at 20 (? approximately equal to 0.72) and the 50% mass fraction burned (MFB 50) was also fixed. The results show that dual-fuel combustion can reduce NO_x and PM emissions in comparison to conventional diesel combustion.     

Effect of injector parameters on the injection quantity of common rail injection system for diesel engines

In this paper, the bond graph model of common rail injector was proposed in consideration of the effects of variable liquid capacitance and fuel physical property on the injection characteristics of the injector. State equations were derived based on the model, which were numerically solved by programming in Matlab. Comparisons between the simulation results and the experimental data show that the numerical model can effectively predict the injection quantity of the system. Effect of variation of delivery chamber diameter, needle seat semi-angle, needle cone semi-angle, ball valve seat semi-angle, nozzle hole diameter, inlet orifice diameter and outlet orifice diameter on fuel injection quantity had been analyzed. The influence rules of various parameters on the fuel injection quantity had been established. The experiments were conducted using face centered central composite design. A second order polynomial response surface model had been developed for predicting fuel injection quantity, as a function of the independent variables. Analysis of variation was used to determine the significance interactions which primarily affect the fuel injection quantity. It had been concluded that six interaction factors including delivery chamber diameter with nozzle hole diameter, needle seat semi-angle with needle cone semi-angle, needle seat semi-angle with nozzle hole diameter, needle cone semi-angle with nozzle hole diameter, nozzle hole diameter with inlet orifice diameter, and nozzle hole diameter with outlet orifice diameter have significant effect on the fuel injection quantity of the system.     

Exhaust emissions and its control methods in compression ignition engines: A review

Extensive usage of automobiles has certain disadvantages and one of them is its negative effect on environment. Carbon dioxide (CO₂), carbon monoxide (CO), hydrocarbons (HC), oxides of nitrogen (NO_x), sulphur dioxide (SO₂) and particulate matter (PM) come out as harmful products during incomplete combustion from internal combustion (IC) engines. As these substances affect human health, regulatory bodies impose increasingly stringent restrictions on the level of emissions coming out from IC engines. This trend suggests the urgent need for the investigation of all aspects relevant to emissions. It is required to modify existing engine technologies and to develop a better after-treatment system to achieve the upcoming emission norms. Diesel engines are generally preferred over gasoline engines due to their undisputed benefit of fuel economy and higher torque output. However, diesel engines produce higher emissions, particularly NO_x and PM. Aftertreatment systems are costly and occupy more space, hence, in-cylinder solutions are preferred in reducing emissions. Exhaust gas recirculation (EGR) technology has been utilized previously to reduce NO_x. Though it is quite successful for small engines, problem persists with large bore engines and with high rate of EGR. EGR helps in reducing NO_x, but increases particulate emissions and fuel consumption. Many in-cylinder solutions such as lower compression ratios, modified injection characteristics, improved air intake system etc. are required along with EGR to accomplish the future emission norms. Modern combustion techniques such as low temperature combustion (LTC), homogeneous charge compression ignition (HCCI), premixed charge compression ignition (PCCI) etc. would be helpful for reducing the exhaust emissions and improving the engine performance. However, controlling of autoignition timing and achieving wider operating range are the major challenges with these techniques. A comprehensive review of diesel engine performance and emission characteristics is given in this paper.     

Experimental study on the characteristics of nano-particle emissions from a heavy-duty diesel engine using a urea-SCR system

Particulate matter in diesel engine exhaust, particularly nano-particles, can cause serious human health problems including diseases such as lung cancer. Because diesel nano-particle issues are of global concern, regulations on particulate matter emissions specify that not only the weight of particulate matter emitted but also the concentration of nanoparticles must be controlled. This study aimed to determine the effects on nano-particle and PM emissions from a diesel engine when applying a urea-SCR system for NO_x reduction. We found that PM weight increases by approximately 90% when urea is injected in ND-13 mode over the emission without urea injection. Additionally, PM weight increases as the NH₃/NO_x mole ratio is increased at 250 °C. In SEM scans of the collected PM, spherical particles were observed during urea injection, with sizes of approximately 200 nm to 1 μm. This study was designed to determine the conditions under which nano-particles and PM are formed in a urea-SCR system and to relate these conditions to particle size and shape via a quantitative analysis in ND-13 mode.     

Effect of UWS injection at low exhaust gas temperature on NO<Subscript>x</Subscript> removal efficiency of diesel engine

Urea-SCR systems have been widely used in diesel vehicles according to the strengthened NO_x (Nitrogen Oxides) emission standard. The NO_x removal efficiencies of the latest well optimized urea-SCR system are above 90 % at moderate exhaust gas temperature of 250 ~ 450 °C. However, a large amount of NO_x is emitted from diesel vehicles at cold start or urban driving conditions, when the exhaust gas temperature is not high enough for SCR catalyst activation. Although many researchs have been stuied to improve NO_x conversion efficiency at these low temperature conditions, it is still one of important technical issues. In this study, the effect of UWS injection at low exhaust gas temperature conditions is studied. This study uses a 3.4 L diesel engine equipped with a commertial urea SCR system. As a result, it is found that about 5 % of NO_x removal efficiency is improved in the NRTC test when UWS injection starts at the SCR inlet temperature of 150 °C compared to 200 °C. It is also found that urea deposits can be formed on the wall of exhaust pipe, when the local wall temperature is lower than temperature of urea decomposition.     

Effect of direct in-cylinder CO2 injection on HCCI combustion and emission characteristics

Fuel injection during negative valve overlap period was used to realize diesel homogeneous charge compression ignition (HCCI) combustion. In order to control the combustion, CO₂ in-cylinder injection was used to simulate external EGR. Effects of CO₂ injection parameters (injection timing, quantity, pressure) on HCCI combustion and emission characteristics were investigated. Experimental results revealed that CO₂ in-cylinder injection can control the start of combustion and effectively reduce NO_x emission. Either advancing CO₂ injection timing or increasing CO₂ injection quantity can reduce peak cylinder pressure and mean gas temperature, delay the starts of low temperature reaction (LTR) and high temperature reaction (HTR), and lower pressure rise rate; NO_x emission was reduced, while smoke, HC, and CO emissions increased. Since the combustion phase was improved, the indicated thermal efficiency was also improved. Injection pressure determines the amount of disturbance introduced into the cylinder. Generally, with the same injection quantity, higher injection pressure results in higher momentum flux and total momentum. Larger momentum flux and momentum has a stronger disturbance to air-fuel mixture, resulting in a more homogeneous mixture; therefore, larger injection pressure leads to lower NO_x and smoke emissions.     

喷孔数调控活性分层对乙醇-柴油双燃料燃烧的影响

基于1台自然吸气的单缸柴油机,结合缸内三维燃烧仿真计算,研究了不同直喷正时、不同预混比例条件下,直喷喷油器的喷孔数对乙醇-柴油双燃料发动机燃烧和排放特性的影响。结果表明,优化直喷喷油器的喷孔数,能影响直喷柴油的缸内分布,调控乙醇-柴油双燃料发动机燃烧过程。减少喷孔数,可以有效降低缸内高活性柴油的分布区域,减少初始着火的位置,从而降低缸内最高燃烧压力和压力升高率,并且可以在炭烟排放保持较低水平的基础上,降低氮氧化物(NO_x)排放。随着乙醇预混比例的增大,喷孔数对燃烧和排放的影响先增大后减小。随着喷油提前角的增大,由于直喷燃油在缸内混合较为均匀,喷孔数的影响作用逐渐减小。     

Evaluation and visualization of stratified ultra-lean combustion characteristics in a spray-guided type gasoline direct-injection engine

To comply with reinforced emission regulations for harmful exhaust gases, including carbon dioxide (CO₂) emitted as a greenhouse gas, improved technologies for reducing CO₂ and fuel consumption are being developed. Stable lean combustion, which has the advantage of improved fuel economy and reduced emission levels, can be achieved using a sprayguided-type direct-injection (DI) combustion system. The system comprises a centrally mounted injector and closely positioned spark plugs, which ensure the combustion reliability of a stratified mixture under ultra-lean conditions. The aim of this study is to investigate the combustion and emission characteristics of a lean-burn gasoline DI engine. At an excess air ratio of 4.0, approximately 23% improvement in fuel economy was achieved through optimal event timing, which was delayed for injection and advanced for ignition, compared to that under stoichiometric conditions, while NO_x and HC emissions increased. The combustion characteristics of a stratified mixture in a spray-guided-type DI system were similar to those in DI diesel engines, resulting in smoke generation and difficulty in three-way catalystutilization. Although a different operating strategy might decrease fuel consumption, it will not be helpful in reducing NO_x and smoke emissions; therefore, alternatives should be pursued to achieve compliance with emission regulations.     

双层分区燃烧系统对高强化柴油机性能的影响

柴油机的燃烧系统是混合气形成质量的关键。为改善某高强化柴油机的燃烧和排放性能,在保证原机压缩比不变的条件下,设计了一种双层双弧脊分区燃烧系统——双层燃烧室匹配双排喷孔,并基于计算流体力学软件Converge进行数值模拟,研究不同上下排喷孔油束夹角对缸内燃烧和排放的影响。研究结果表明:新设计的燃烧系统的燃烧和排放性能均优于原机,上下排喷孔油束夹角会影响燃油在上下层弧脊处的分配,较大的上排喷孔油束夹角有利于对燃烧室顶隙空间的利用和上层弧脊下侧混合气的形成,较小的下排喷孔油束夹角有利于燃烧室底部凹坑附近空气利用率的提高和混合气分布范围的增加。因此,需要对上下排喷孔油束夹角进行合理的选择和匹配,使得发动机的整体燃烧和排放性能达到最优。     

喷孔布置对缸内油气混合与燃烧过程的影响

基于YD4A75—C3电控共轨柴油机,结合Bosch公司提出的第四代共轴向可变喷嘴共轨喷射系统的概念,应用商用CFD软件Fire研究喷孔交错布置及两层布置对缸内燃油分布及燃烧过程的影响。研究结果表明:适当地采用双层、交错排列的喷孔,可以扩大燃油的空间分布范围,改善燃油与空气的混合质量,使缸内燃烧更加充分;NO排放量增多,但炭烟的排放量显著减少。     

Analysis of the transient atomization characteristics of diesel spray using time-resolved PDPA data

The transient atomization characteristics of a single-hole diesel spray were investigated to clarify the time-dependent droplet formation process of the spray through time-resolved analysis of the droplet size data acquired by using a 2-D PDPA (phase Doppler particle analyzer). Comparisons among the three single-hole diesel nozzles on the atomization characteristics were made to confirm the effects of the hole-diameter. The hole diameter of the single-hole diesel nozzles varied with d_n=0.22, 0.32 and 0.42 mm. The time-resolved diameter, SMD (Sauter mean diameter) and AMD (arithmetic mean diameter) of droplets in diesel spray injected into still ambient air were measured. The SMD and AMD decreased with decreasing nozzle hole diameter. The SMD distribution along the spray centerline steeply decreased with increasing axial distance before reaching a constant value. In the time-dependent analysis of the SMD of the whole flow field, the SMD gradually increased with time after the initiation of injection, reached a maximum value, and then decreased.     

Injection Characteristics of Palm Methyl Ester Blended with Diesel Using Zuech’s Chamber

This research attempts to characterize the injection of palm biodiesel blended with diesel in a Zuech’s chamber. Thailand conventional diesel (mandated blend of biodiesel at 5 % or B5), palm biodiesel (B100) and four other biodiesel blends ratios (B20, B40, B60 and B80) were investigated with single hole injector of 140 and 200 μm diameters, injection pressure of 40 MPa to 160 MPa, constant back pressure of 4.5 MPa and energize time of 2.5 ms. The results show that increasing biodiesel blending ratios leads to longer injection delay, larger injection pressure drop, smaller injection quantity discharge coefficient (C_d) and shorter injection duration. With increasing biodiesel blending ratio, high Cavitation number from biodiesel viscosity decreases Reynolds number. Increasing injector diameter from 140 μm to 200 μm has reduced injection delay, increased fuel injection quantity, discharge coefficient and remaining injection duration. The increasing of injection pressure were improve, injection delay, injection duration, injection quantity and discharge coefficient until injection pressure 120 MPa. In addition at injection pressure over 120 MPa are decrease injection quantity and discharge coefficient, it effect form the cavitation phenomena. Increasing of viscosity, density, Bulk modulus and sound velocity were effect to increase injection delay, with reduce injection quantity, injection duration and pressure drop during injection process.     

柴油掺混二甲醚喷雾粒子尺寸分布特性试验研究

为确定二甲醚掺入柴油后对燃料雾化性能的改善效果,利用阴影成像与数字图像处理技术,对不同掺混比、喷射压力以及喷孔直径等条件下的二甲醚-柴油混合燃料喷雾粒子尺寸分布特性进行了对比试验研究.结果发现:由于柴油中二甲醚的闪急沸腾作用,随着二甲醚掺混比的增加,混合燃料粒子尺寸分布曲线整体向小颗粒方向偏移,较大粒子数目较柴油明显减少,有助于降低发动机炭烟排放;喷孔直径、喷射压力等喷射参数对混合燃料雾化粒子分布有较大影响,减小喷孔直径使燃油粒子更加细化,降低喷射压力则使混合燃料雾化效果有变差的趋势.     

Computational study on the effects of volume ratio of DOC/DPF and catalyst loading on the PM and NOx emission control for heavy-duty diesel engines

The use of a diesel particulate filter (DPF) in a diesel aftertreatment system has proven to be an effective and efficient method for removing particulate matter (PM) in order to meet more stringent emission regulations without hurting engine performance. One of the favorable PM regeneration technologies is the NO₂-assisted regeneration method due to the capability of continuous regeneration of PM under a much lower temperature than that of thermal regeneration. In the present study, the thermal behavior of the monolith during regeneration and the conversion efficiency of NO₂ from NO with an integrated exhaust system of a diesel oxidation catalyst (DOC) and DPF have been predicted by one-channel numerical simulation. The simulation results of the DOC, DPF, and integrated DOC-DPF models are compared with experimental data to verify the accuracy of the present model for the integrated DOC and DPF modeling. The effects of catalyst loading inside the DOC and the volume ratio between the DOC and DPF on the pressure drop, the conversion efficiency, and the oxidation rate of PM, have been numerically investigated. The results indicate that the case of the volume ratio of ‘DOC/DPF=1.5’ within the same diameter of both monoliths produced close to the maximum conversion efficiency and oxidation rate of PM. Under the engine operating condition of 175 kW at 2200 rpm, 100% load with a displacement of 8.1, approximately 55 g/ft³ of catalyst (Pt) loading inside the DOC with the active Pt surface of 5.3 m²/g_pt was enough to maximize the conversion efficiency and oxidation rate of PM.     

多次喷射对柴油机燃烧与排放影响的试验研究

基于1台高压共轨涡轮增压柴油机,采用不同的预喷正时、预喷油量与后喷正时等,研究了多次喷射对燃烧放热、排放生成与燃油经济性的影响,以实现均质压燃和低温燃烧过程。研究结果表明:随预喷正时提前,缸内峰值压力降低,主燃阶段的滞燃期缩短,NOx和炭烟排放均降低;随预喷油量增加,预喷阶段燃烧的放热率和最大压力升高率增大,NOx和HC排放增大,而PM和CO排放降低;随后喷始点推迟,缸内压力与主放热率峰值差异变小,NOx排放降低,但炭烟排放先增大后逐渐降低。     

Influence of pilot injection on combustion characteristics and emissions in a DI diesel engine fueled with diesel and DME

This work experimentally investigates how the dwell time between pilot injection and main injection influences combustion and emissions characteristics (NOx, CO, THC and smoke) in a single-cylinder DI diesel engine. The experiments were conducted using two fuel injection systems according to the fuel type, diesel or dimethyl ether (DME), due to the different fuel characteristics. The injection strategy is accomplished by varying the dwell time (10°CA, 16°CA and 22°CA) between injections at five main injection timings (?4°CA aTDC, ?2°CA aTDC, 0°CA aTDC, 2°CA aTDC and 4°CA aTDC). Results from pilot-main injection conditions are compared with those shown in single injection conditions to better demonstrate the potential of pilot injection. It was found that pilot injection is highly effective for lowering heat-release rates with smooth pressure traces regardless of the fuel type. Pilot injection also offers high potential to maintain or increase the BMEP; even the combustion-timing is retarded to suppress the NOx emission formation. Overall, NOx emission formation was suppressed more by the combustion phasing retard effect, and not the pilot injection effect considered in this study. Comparison of the emissions for different fuel types shows that CO and HC emissions have low values below 100 ppm for DME operation in both single injection and pilot-main injection. However, NOx emission is slightly higher in the earlier main injection timings (?4°CA aTDC, ?2°CA aTDC) than diesel injections. Pilot injection was found to be more effective with DME for reducing the amount of NOx emission with combustion retardation, which indicates a level of NOx emission similar to that of diesel. Although the diesel pilot-main injection conditions show higher smoke emission than single-injection condition, DME has little smoke emission regardless of injection strategy.     

Urea-SCR system optimization with various combinations of mixer types and decomposition pipe lengths

The demand for NO_x after-treatment system has increased dramatically due to the stricter NO_x emission regulations for diesel vehicles. The urea-SCR system is one of the NO_x after-treatment methods found to be quite effective to meet the regulation requirement enforced by various authorities including the Euro-6. In order to develop an effective urea-SCR system, it is critical to establish an even distribution of reductant over the catalyst surface since this favorable distribution can increase reduction reaction and in turn, improve NO_x conversion efficiencies. In the current study, a number of design variations of the urea-SCR system which included two mixer types and three decomposition pipe lengths, were evaluated systematically using CFD analysis and experimental measurements. The purpose of the CFD analysis was to estimate the distribution of reductant within the urea-SCR system with a specific configuration and the purpose of the engine emission test was to measure the amount of NO_x reduction, respectively. The results from the systematic analysis revealed the relation between the reductant distribution over the SCR and the performance of the NO_x reduction.     

燃油含硫量对柴油机微粒排放影响的研究

选择两台涡轮增压柴油机,一台在发动机试验台上进行ECE R-49试验,另一台4缸、直喷共轨、2 L排量的柴油机装车在汽车底盘测功器上进行NEDC试验,研究了含S量对柴油机PM排放的影响。结果表明,柴油中的含S量对柴油机PM排放有很大影响,减少柴油含S量能直接降低柴油机的PM排放。