Development of two driving cycles for utility vehicles

Driving cycles are used to assess vehicle fuel consumption and pollutant emissions. The premise in this article is that suburban road-work vehicles and airport vehicles operate under particular conditions that are not taken into account by conventional driving cycles. Thus, experimental data were acquired from two pickup trucks representing both vehicle fleets that were equipped with a data logger. Based on experimental data, the suburban road-work vehicle showed a mixed driving behavior of high and low speed with occasional long periods of idling. In the airport environment, however, the driving conditions were restricted to airport grounds but were characterized by many accelerations and few high speeds. Based on these measurements, microtrips were defined and two driving cycles proposed. Fuel consumption and pollutant emissions were then measured for both cycles and compared to the FTP-75 and HWFCT cycles, which revealed a major difference: at least a 31% increase in fuel consumption over FTP-75. This increased fuel consumption translates into higher pollutant emissions. When CO₂ equivalent emissions are taken into account, the proposed cycles show an increase of at least 31% over FTP-75 and illustrate the importance of quantifying fleet speed patterns to assess CO₂ equivalent emissions so that the fleet manager can determine potential gains in energy or increased pollutant emissions.     

Development of the World-wide harmonized Light duty Test Cycle (WLTC) and a possible pathway for its introduction in the European legislation

This paper presents the World-wide harmonized Light duty Test Cycle (WLTC), developed under the Working Party on Pollution and Energy (GRPE) and sponsored by the European Union (with Switzerland) and Japan. India, Korea and USA have also actively contributed. The objective was to design the harmonized driving cycle from “real world” driving data in different regions around the world, combined with suitable weighting factors. To this aim, driving data and traffic statistics of light duty vehicles use were collected and analyzed as basic elements to develop the harmonized cycle. The regional driving data and weighting factors were then combined in order to develop a unified database representing the worldwide light duty vehicle driving behavior. From the unified database, short trips were selected and combined to develop a driving cycle as representative as possible of the unified database. Approximately 765,000 km of data were collected, covering a wide range of vehicle categories, road types and driving conditions. The resulting WLTC is an ensemble of three driving cycles adapted to three vehicle categories with different power-to-mass ratio (PMR). It has been designed as a harmonized cycle for the certification of light duty vehicles around the world and, together with the new harmonized test procedures (WLTP), will serve to check the compliance of vehicle pollutant emissions with respect to the applicable emissions limits and to establish the reference vehicle fuel consumption and CO₂ performance.     

Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

Analysis of vehicle emission measurements on the new WLTC,the NEDC and the CADC

Several studies have shown that the type-approval data is not representative for real-world usage. Consequently, the emissions and fuel consumption of the vehicles are underestimated. Aiming at a more dynamic and worldwide harmonised test cycle, the new Worldwide Light-duty Test Cycle is being developed. To analyse the new cycle, we have studied emission results of a test programme of six vehicles on the test cycles WLTC (Worldwide Light-duty Test Cycle), NEDC (New European Driving Cycle) and CADC (Common Artemis Driving Cycle). This paper presents the results of that analysis using two different approaches. The analysis shows that the new driving cycle needs to exhibit realistic warm-up procedures to demonstrate that aftertreatment systems will operate effectively in real service; the first trip of the test cycle could have an important contribution to the total emissions depending on the length of the trip; and that there are some areas in the acceleration vs. vehicle speed map of the new WLTC that are not completely filled, especially between 70 and 110 km/h. For certain vehicles, this has a significant effect on total emissions when comparing this to the CADC.     

Development of real-world driving cycle: Case study of Pune,India

The critical component of all emission models is a driving cycle representing the traffic behaviour. Although Indian driving cycles were developed to test the compliance of Indian vehicles to the relevant emission standards, they neglects higher speed and acceleration and assume all vehicle activities to be similar irrespective of heterogeneity in the traffic mix. Therefore, this study is an attempt to develop an urban driving cycle for estimating vehicular emissions and fuel consumption. The proposed methodology develops the driving cycle using micro-trips extracted from real-world data. The uniqueness of this methodology is that the driving cycle is constructed considering five important parameters of the time–space profile namely, the percentage acceleration, deceleration, idle, cruise, and the average speed. Therefore, this approach is expected to be a better representation of heterogeneous traffic behaviour. The driving cycle for the city of Pune in India is constructed using the proposed methodology and is compared with existing driving cycles.     

Electric vehicles’ energy consumption estimation with real driving condition data

The use of electric vehicles (EVs) is viewed as an attractive option to reduce CO₂ emissions and fuel consumption resulted from transport sector, but the popularization of EVs has been hindered by the cruising range limitation and the charging process inconvenience. Energy consumption characteristics analysis is the important foundation to study charging infrastructures locating, eco-driving behavior and energy saving route planning, which are helpful to extend EVs’ cruising range. From a physical and statistical view, this paper aims to develop a systematic energy consumption estimation approach suitable for EV actual driving cycles. First, by employing the real second-by-second driving condition data collected on typical urban travel routes, the energy consumption characteristics analysis is carried out specific to the microscopic driving parameters (instantaneous speed and acceleration) and battery state of charge (SOC). Then, based on comprehensive consideration of the mechanical dynamics characteristics and electric machine system of the EVs, a set of energy consumption rate estimation models are established under different operation modes from a statistical perspective. Finally, the performance of proposed model is fully evaluated by comparing with a conventional energy consumption estimation method. The results show that the proposed modeling approach represents a significant accuracy improvement in the estimation of real-world energy consumption. Specifically, the model precision increases by 25.25% in decelerating mode compared to the conventional model, while slight improvement in accelerating and cruising mode with desirable goodness of fit.     

Conventional,hybrid and electric vehicles for Australian driving conditions. Part 2: Life cycle CO2-e emissions

This paper is the second of a two part study which quantifies the economic and greenhouse performance of conventional, hybrid and fully electric passenger vehicles operating in Australian driving conditions. This second study focuses on the life cycle greenhouse gas emissions. Two vehicle sizes are considered, Class-B and Class-E, which bracket the large majority of passenger vehicles on Australian roads.Using vehicle simulation models developed in the first study, the trade-offs between the ability of increasingly electric powertrains in curtailing the tailpipe emissions and the corresponding rise in the embedded vehicle emissions have been evaluated. The sensitivity of the life cycle emissions to fuel, electricity and the change in the energy mix are all considered. In conjunction with the total cost of ownership calculated in the companion paper, this allows the cost of mitigating life cycle greenhouse gas emissions through electrification of passenger transport to be estimated under different scenarios. For Class-B vehicles, fully electric vehicles were found to have a higher total cost of ownership and higher life cycle emissions than an equivalent vehicle with an internal combustion engine. For Class-E vehicles, hybrids are found to be the most cost effective whilst also having lowest life cycle emissions under current conditions. Further, hybrid vehicles also exhibit little sensitivity in terms of greenhouse emissions and cost with large changes in system inputs.     

Development of a driving cycle for fuel economy in a developing country

A driving cycle corresponding to the driving conditions of a particular country is of decisive importance for fuel economy evaluation of vehicles and automobile engines. The driving pattern was studied in Delhi along four representative routes using a test car equipped with all the instruments required for recording modes of traffic and measuring fuel consumption. An analysis of the field trials results has shown that relative time spent under different modes (cruising, acceleration, etc.) does not practically depend upon a route and rush-or-non rush conditions. Fuel consumption is a function of the average speed and trip length. A four-mode driving cycle has been developed to simulate actual driving conditions with respect to fuel consumption. In comparison with driving cycles of developed countries, the driving cycle has significantly different average speed and relative time spent under acceleration and deceleration. The cycle may be used as a standardized method to evaluate fuel efficiency of vehicles and automobile engines and effect of various gadgets on its improvement.     

Reducing CO2 emissions of conventional fuel cars by vehicle photovoltaic roofs

The European Union has adopted a range of policies aiming at reducing greenhouse gas emissions from road transport, including setting binding targets for tailpipe CO₂ emissions for new light-duty fleets. The legislative framework for implementing such targets allows taking into account the CO₂ savings from innovative technologies that cannot be adequately quantified by the standard test cycle CO₂ measurement. This paper presents a methodology to define the average productivity of vehicle-mounted photovoltaic roofs and to quantify the resulting CO₂ benefits for conventional combustion engine-powered passenger cars in the European Union. The method relies on the analysis of a large dataset of vehicles activity data, i.e. urban driving patterns acquired with GPS systems, combined with an assessment of the shading effect from physical obstacles and indoor parking. The results show that on average the vehicle photovoltaic roof receives 58% of the available solar radiation in real-world conditions, making it possible to reduce CO₂ emissions from passenger cars in a range from 1% to 3%, assuming a storage capacity of 20% of the 12 V battery dedicated to solar energy. This methodology can be applied to other vehicles types, such as light and heavy-duty, as well as to different powertrain configurations, such as hybrid and full electric.     

Comparative evaluation of eight legislated driving schedules in terms of cycle metrics and emissions from a diesel-powered turbocharged van

The present work compares, on a fundamental basis, the performance and emissions of a diesel-engined large van running on eight legislated driving cycles, namely the European NEDC, the U.S. FTP-75, HFET, US06, LA-92 and NYCC, the Japanese JC08 and the Worldwide WLTC 3-2. It aims to identify differences and similarities between various influential driving cycles valid in the world, and correlate important cycle metrics with vehicle exhaust emissions. The results derive from a computational code based on an engine mapping approach, with experimentally derived correction coefficients applied to account for transient discrepancies; the code is coupled to a comprehensive vehicle model. Soot as well as nitrogen monoxide are the examined pollutants. Only the driving cycle schedule is under investigation in this work, and not the whole test procedure, in order to identify vehicle speed (transient) effects of the individual cycles only. The recently developed WLTC 3-2 is the cycle with a very broad and at the same time dense coverage of the vehicle’s/engine’s operating activity, being thus particularly representative of ‘average’ real-world driving. Even broader is the distribution of the US06, whereas particularly thin and narrow that of the modal NEDC. It is also revealed that the more transient cycles, e.g. the NYCC or the US06, are also the ones with the highest amount of engine-out pollutant emissions and energy consumption. Relative positive acceleration and stops per km are found to correlate very well with energy and fuel consumption and all emitted pollutants.     

A statistical model for estimating oxides of nitrogen emissions from light duty motor vehicles

Motor vehicle emission rate models for predicting oxides of nitrogen (NOx) emissions are insensitive to vehicle modes of operation such as cruise, acceleration, deceleration, and idle, because they are based on average trip speed. Research has shown that NOx emissions are sensitive to engine load; hence, load-based variables need to be included in emissions models. Ongoing studies attempting to incorporate these `modal' variables have experienced difficulties with: (1) incomplete and/or non-representative data sets of emissions test data vis-a-vis the modal operating profiles of the tested vehicles; (2) lack of information for predicting on-road operating parameters of vehicles; and (3) non-representative vehicles recruited for emissions tests.The objective of this research was to develop a statistical model for predicting NOx emissions from light-duty gasoline motor vehicles. The primary end use of this model is forecasting, rather than explanation of the factors that affect NOx emissions, which brings to bear different requirements from the statistical model. The three challenges noted above are addressed by: (1) analyzing a data set of more than 13 000 hot-stabilized laboratory treadmill tests on 19 driving cycles (specific speed versus time testing conditions), and 114 variables describing vehicle, engine and test cycle characteristics; (2) making the models compatible with empirical data on how vehicles are being operated in-use; and (3) developing statistical weights to account for the differences in model year distributions between the emissions testing database and the current national on-road fleets.The NOx emissions model is estimated using ordinary least-squares regression techniques, with transformed response variable and regression weights. Tree regression is employed as a tool for mining relationships among variables in the data, with particular focus on identifying useful interactions among discrete variables. Details of the model development process are presented, as well as results for the final model showing the predicted emissions algorithm for the current motor vehicle fleet in Atlanta, GA metropolitan region.     

The vehicle emissions and performance monitoring system: analysis of tailpipe emissions and vehicle performance

This paper describes tailpipe emission results generated by the Vehicle Performance and Emissions Monitoring system (VPEMS). VPEMS integrates on‐board emissions and vehicle/driver performance measurements with positioning and communications technologies, to transmit a coherent spatio‐temporally referenced dataset to a central base station in near real time. These results focus on relationships between tailpipe emissions of CO, CO₂, NO_x and speed and acceleration. Emissions produced by different driving modes are also presented. Results are generally as one would expect, showing variation between vehicle speed, vehicle acceleration and emissions. Data is based upon a test run in central London on urban streets with speeds not exceeding about 65 km/h. The results presented demonstrate the capabilities of the system. Various issues remain with regard to validation of the data and expansion of the system capability to obtain additional vehicle performance data.     

Environmental assessment of electrification of road transport in Norway: Scenarios and impacts

The study develops scenarios regarding the introduction of electric vehicles to the passenger vehicle fleet of Norway to reach the 2020 Norwegian greenhouse gas reduction target and a more extreme target to limit global temperature increase to two degrees. A process-based life cycle assessment approach is integrated with a temporally variable inventory model to evaluate the environmental impacts of these scenarios. We find that greenhouse gases in the reference scenario increase by 10% in 2020 in comparison to 2012; while for the more intensive improvements in conventional vehicles, this increase is reduced to 2%. For electric vehicles deployment scenarios, although the fleet share will reduce the tailpipe greenhouse gas emissions by 8–26%, with the upper end representing the two-degree reduction target, emissions reductions over the entire life cycle are only 3–15%. Electric vehicles also reduce emissions of NO_x, SO₂ and particulates reducing acidification, smog formation and particulate formation impacts, however, with addition of large numbers of electric vehicles significant trade-offs in toxicity impacts are found.     

Optimal fleet conversion policy from a life cycle perspective

Vehicles typically deteriorate with accumulating mileage and emit more tailpipe air pollutants per mile. Although incentive programs for scrapping old, high-emitting vehicles have been implemented to reduce urban air pollutants and greenhouse gases, these policies may create additional sales of new vehicles as well. From a life cycle perspective, the emissions from both the additional vehicle production and scrapping need to be addressed when evaluating the benefits of scrapping older vehicles. This study explores an optimal fleet conversion policy based on mid-sized internal combustion engine vehicles in the US, defined as one that minimizes total life cycle emissions from the entire fleet of new and used vehicles. To describe vehicles' lifetime emission profiles as functions of accumulated mileage, a series of life cycle inventories characterizing environmental performance for vehicle production, use, and retirement was developed for each model year between 1981 and 2020. A simulation program is developed to investigate ideal and practical fleet conversion policies separately for three regulated pollutants (CO, NMHC, and NO_x) and for CO₂. According to the simulation results, accelerated scrapping policies are generally recommended to reduce regulated emissions, but they may increase greenhouse gases. Multi-objective analysis based on economic valuation methods was used to investigate trade-offs among emissions of different pollutants for optimal fleet conversion policies.     

Development a new power management strategy for power split hybrid electric vehicles

Reduction of greenhouse gas emission and fuel consumption as one of the main goals of automotive industry leading to the development hybrid vehicles. The objective of this paper is to investigate the energy management system and control strategies effect on fuel consumption, air pollution and performance of hybrid vehicles in various driving cycles. In order to simulate the hybrid vehicle, the combined feedback–feedforward architecture of the power-split hybrid electric vehicle based on Toyota Prius configuration is modeled, together with necessary dynamic features of subsystem or components in ADVISOR. Multi input fuzzy logic controller developed for energy management controller to improve the fuel economy of a power-split hybrid electric vehicle with contrast to conventional Toyota Prius Hybrid rule-based controller. Then, effects of battery’s initial state of charge, driving cycles and road grade investigated on hybrid vehicle performance to evaluate fuel consumption and pollution emissions. The simulation results represent the effectiveness and applicability of the proposed control strategy. Also, results indicate that proposed controller is reduced fuel consumption in real and modal driving cycles about 21% and 6% respectively.     

Real-world gaseous emission characteristics of Euro 6b light-duty gasoline- and diesel-fueled vehicles

To accurately investigate vehicle emissions that have become major contributors to global air pollutants and greenhouse gases, test conditions have been transferred from laboratory type approval test cycles to real-world driving conditions. In this study, the real-world driving emissions of carbon monoxide (CO), total hydrocarbons (THC), nitrogen oxides (NO_x), and carbon dioxide (CO₂) from one gasoline and two diesel Euro 6b light-duty passenger vehicles were investigated by a portable emission measurement system (PEMS) in Lyon, France. NO_x and CO₂ emission controls remain critical to addressing the real-world driving emissions of Euro 6b vehicles. Notably, the tested gasoline vehicle emitted higher CO₂ emissions than diesel vehicles on all types of roads, especially on the urban road with an excess of 29.3–48.3%. The highest emission factors of gaseous pollutants generally occurred on the motorway for the gasoline vehicle, while on the urban road for diesel vehicles. In particular, for high-speed driving conditions, the gasoline vehicle gaseous emissions, especially NO_x emissions, were more affected by acceleration than diesel vehicle emissions. In addition, the CO emissions, especially THC emissions, for the gasoline vehicle, were more influenced by warm-start, especially cold-start, than those for diesel vehicles.     

Comparative analysis of the energy consumption and CO2 emissions of 40 electric,plug-in hybrid electric,hybrid electric and internal combustion engine vehicles

This paper analyses the results of the Royal Automobile Clubhallo’s 2011 RAC Future Car Challenge, an annual motoring challenge in which participants seek to consume the least energy possible while driving a 92 km route from Brighton to London in the UK. The results reveal that the vehicle’s power train type has the largest impact on energy consumption and emissions. The traction ratio, defined as the fraction of time spent on the accelerator in relation to the driving time, and the amount of regenerative braking have a significant effect on the individual energy consumption of vehicles. In contrast, the average speed does not have a great effect on a vehicles’ energy consumption in the range 25–70 km/h.     

Predicting market potential and environmental benefits of deploying electric taxis in Nanjing,China

This paper investigates the market potential and environmental benefits of replacing internal combustion engine (ICE) vehicles with battery electric vehicles (BEVs) in the taxi fleet in Nanjing, China. Vehicle trajectory data collected by onboard global positioning system (GPS) units are used to study the travel patterns of taxis. The impacts of charger power, charging infrastructure coverage, and taxi apps on the feasibility of electric taxis are quantified, considering taxi drivers’ recharging behavior and operating activities. It is found that (1) depending on the charger power and coverage, 19% (with AC Level 2 chargers and 20% charger network coverage) to 56% (with DC chargers and 100% charger network coverage) of the ICE vehicles can be replaced by electric taxis without driving pattern changes; (2) by using taxi apps to find nearby passengers and charging stations, drivers could utilize the empty cruising time to charge the battery, which may increase the acceptance of BEVs by up to 82.6% compared to the scenario without taxi apps; and (3) tailpipe emissions in urban areas could be significantly reduced with taxi electrification: a mixed taxi fleet with 46% compressed-natural-gas-powered (CNG) and 54% electricity-powered vehicles can reduce the tailpipe emissions by 48% in comparison with the fleet of 100% CNG taxis.     

A control theoretic formulation of green driving strategies based on inter-vehicle communications

Various green driving strategies have been proposed to smooth traffic flow and lower pollutant emissions and fuel consumption in stop-and-go traffic. In this paper, we present a control theoretic formulation of distributed, cooperative green driving strategies based on inter-vehicle communications (IVCs). The control variable is the advisory speed limit, which is designed to smooth a following vehicle’s speed profile without changing its average speed. We theoretically analyze the performance of a constant independent and three simple cooperative green driving strategies and present three rules for effective and robust strategies. We then develop a distributed cooperative green driving strategy, in which the advisory speed limit is first independently calculated by each individual vehicle and then averaged among green driving vehicles through IVC. By simulations with Newell’s car-following model and the Comprehensive Modal Emissions Model (CMEM), we demonstrate that such a strategy is effective and robust independently as well as cooperatively for different market penetration rates of IVC-equipped vehicles and communication delays. In particular, even when 5% of the vehicles implement the green driving strategy and the IVC communication delay is 60 s, the fuel consumption can be reduced by up to 15%. Finally we discuss some future extensions.     

Customizing driving cycles to support vehicle purchase and use decisions: Fuel economy estimation for alternative fuel vehicle users

Wider deployment of alternative fuel vehicles (AFVs) can help with increasing energy security and transitioning to clean vehicles. Ideally, adopters of AFVs are able to maintain the same level of mobility as users of conventional vehicles while reducing energy use and emissions. Greater knowledge of AFV benefits can support consumers’ vehicle purchase and use choices. The Environmental Protection Agency’s fuel economy ratings are a key source of potential benefits of using AFVs. However, the ratings are based on pre-designed and fixed driving cycles applied in laboratory conditions, neglecting the attributes of drivers and vehicle types. While the EPA ratings using pre-designed and fixed driving cycles may be unbiased they are not necessarily precise, owning to large variations in real-life driving. Thus, to better predict fuel economy for individual consumers targeting specific types of vehicles, it is important to find driving cycles that can better represent consumers’ real-world driving practices instead of using pre-designed standard driving cycles. This paper presents a methodology for customizing driving cycles to provide convincing fuel economy predictions that are based on drivers’ characteristics and contemporary real-world driving, along with validation efforts. The methodology takes into account current micro-driving practices in terms of maintaining speed, acceleration, braking, idling, etc., on trips. Specifically, using a large-scale driving data collected by in-vehicle Global Positioning System as part of a travel survey, a micro-trips (building block) library for California drivers is created using 54 million seconds of vehicle trajectories on more than 60,000 trips, made by 3000 drivers. To generate customized driving cycles, a new tool, known as Case Based System for Driving Cycle Design, is developed. These customized cycles can predict fuel economy more precisely for conventional vehicles vis-à-vis AFVs. This is based on a consumer’s similarity in terms of their own and geographical characteristics, with a sample of micro-trips from the case library. The AFV driving cycles, created from real-world driving data, show significant differences from conventional driving cycles currently in use. This further highlights the need to enhance current fuel economy estimations by using customized driving cycles, helping consumers make more informed vehicle purchase and use decisions.