规则纵浪中船舶参数激励横摇运动研究

考虑船舶横摇运动中恢复力矩及阻尼力矩的非线性,建立船舶在规则波浪中参数激励下的非线性横摇运动方程,并对规则纵浪中船舶参数激励横摇运动进行研究,探讨船舶发生参数激励横摇运动的条件及大幅横摇的动力学特征,分析船速、波高及波长等因素对参数激励横摇运动的影响。     

Probabilistic assessment of parametric instability of a top tensioned riser in irregular waves

A reliability analysis was used to investigate the parametric instability of a top tensioned riser (TTR) operating under irregular sea conditions. In practical applications, the parametric instability evaluation of a riser is a very difficult task, owing to uncertainty of various parameters such as the environmental conditions of the load, the structural geometric parameters, and material properties. Considering the uncertainties of these parameters, it is vital to adopt a probabilistic approach in evaluating the instability. In this work, the Hill equation of a TTR operating under real sea conditions is first derived, and the corresponding stochastic external excitation is obtained using the Pierson–Moskowitz wave spectrum. The effects of various random variables on the parametric instability are studied by a sensitivity analysis. A surrogate model is used to construct the response surface for assessing the reliability of the parametric instability of the riser. The distribution regularity of parametrically unstable cases is examined using the contour of the parametrically excited responses. The effect of three significant uncertain factors on the probability of the parametric stability is investigated using the surrogate model. The proposed approach is demonstrated to be efficient for evaluating the reliability of the parametric instability of a TTR.     

Theoretical study on the effect of parametric rolling on added resistance in regular head seas

A formula based on Maruo’s theory is presented for the added resistance in regular head seas when parametric rolling occurs. Firstly, the velocity potential of the radiation waves due to parametric rolling, sway and yaw motions should be superposed on the conventional velocity potential. Secondly, the added resistance is averaged within the time duration that is double the encounter period. Thirdly, the stationary-phase method which is used in Maruo’s method is also used to obtain the formula of added resistance in waves with parametric rolling taken into account as well as viscous roll damping. Fourthly, source distribution based on Maruo and Ishii's and Maruo and Iwase’s works is used to calculate the added resistance. Finally, the effect of parametric rolling on added resistance in regular head seas mainly results from viscous roll damping and it becomes larger as the amplitude of parametric rolling becomes larger.     

参数化技术在舰船结构设计中的应用

参数化设计是指设计人员在CAD系统提供的条件下用一组参数来构造设计对象的信息模型,参数与设计对象的控制尺寸有显式对应,当参数的值发生变化时,设计对象随之改变。本文结合CATIAV5系统,介绍了参数化设计技术,阐述了参数化建模的几种方法。以甲板支柱为例,建立了支柱的参数化模型,实现支柱的参数化设计和模型自动修改的功能,大大节约了设计时间。     

On the Parametric Resonance of Tumblehome Hullforms in a Longitudinal Seaway

This work presents a numerical study of the influence of topside shape on parametric roll in longitudinal seas. The ONR 3 Topsides hulls are used to compare the single degree-of-freedom rolling response of a destroyer-sized vessel with flared (model 5613), tumblehome (model 5613-1), and wallsided (model 5613-2) shapes above the waterline. Through this relative comparison, the key aspects of parametric resonance of a tumblehome hullform are highlighted, namely the reduction in head seas forward speed required to encounter parametric roll. A variant on the Mathieu equation is used to simulate roll motions.     

纵向规则波中参数横摇的数值模拟

基于ITTC推荐的参数横摇运动方程,采用估算方法确定方程中的阻尼系数和复原力矩系数,数值模拟出船舶在规则波中的参数横摇情况,将上述方法具体应用于一艘滚装船船模的参数横摇预报,并与试验数据进行对比,验证了所采用方法的有效性。     

基于设计特征的FRIENDSHIP船型参数化方法及实现

船型设计是船舶总体设计中一项极其复杂且又重要的内容,船舶的结构设计、性能计算、总布置等都要以船型为依据,因此,如何实现船型参数化设计尤为重要。FRIENDSHIP系统为船型设计提供了基于Feature特征和仿真驱动设计的参数化方法和实现机制。在对船型参数化基本理论———特征参数、特征曲线和曲面生成等进行详细阐述的基础上,以某型船艉部裸船体为例,具体阐述了船型参数化的实现流程,以及以Feature、Curveengine和Meta surface为特征机制的船型参数化的具体步骤。以Feature特征为核心的船型参数化方法不仅能为船型曲面的快速建立提供技术支撑,还可以为性能分析和优化提供基础条件。     

Parametric rolling prediction in irregular seas using combination of deterministic ship dynamics and probabilistic wave theory

In recent years there have been reports of serious accidents of parametric rolling for modern container ships and car carriers. For avoiding such accidents, a prediction method of parametric rolling in irregular seas is required. Since parametric rolling is practically non-ergodic, repetitions of numerical simulations or experiments could be not feasible to ascertain the behaviour. Therefore, in this paper, a method combining a stochastic approach with a deterministic approach in order to estimate the probabilistic index without such simple repetitions is developed. The ship's response in regular seas is estimated by solving an averaged system of the original 1-DoF roll model, and random waves necessary for occurrence of parametric rolling is achieved by using Longuet-Higgins’s or Kimura’s wave group theory. As a result, a fast and robust computation method of the probabilistic index is established. Finally, it is concluded that the proposed method is considered to be one of the useful tools for discussing the new IMO Intact Stability Code.     

风力载荷对实船参数横摇预报的影响研究

参数横摇作为一种严重危害船舶安全的现象,已被国际海事组织(IMO)列为重要的稳性失效模式开展研究。集装箱船的事故报告表明,参数横摇现象发生于相对恶劣的海况条件下,且伴随相应的气象条件。由于此时风力载荷是船舶航行过程中不可忽略的因素,因而非常有必要研究其对参数横摇运动的影响。文中基于弱非线性三自由度运动模型,通过对4艘实船参数横摇响应的计算研究,发现风力载荷对于集装箱船在规则波中的参数横摇具有重要影响,对于参数横摇起促进作用。     

NURBS曲面与隐式曲面求交的计算机实现及应用

阐述了参数曲面与隐式曲面求交的算法原理，给出计算机实现方法及交点可能的分布示意图，将其应用于基于NURBS的船体曲面与任意平面的求交中，并针对船体曲面的特点指出应用过程中应注意的问题。     

A numerical study on piezoelectric energy harvesting by combining transverse galloping and parametric instability phenomena

This paper aims to numerically investigate the effects of parametric instability on piezoelectric energy harvesting from the transverse galloping of a square prism. A two degrees-of-freedom reduced-order model for this problem is proposed and numerically integrated. A usual quasi-steady galloping model is applied, where the transverse force coefficient is adopted as a cubic polynomial function with respect to the angle of attack. Time-histories of nondimensional prism displacement, electric voltage and power dissipated at both the dashpot and the electrical resistance are obtained as functions of the reduced velocity. Both, oscillation amplitude and electric voltage, increased with the reduced velocity for all parametric excitation conditions tested. For low values of reduced velocity, 2:1 parametric excitation enhances the electric voltage. On the other hand, for higher reduced velocities, a 1:1 parametric excitation (i.e., the same as the natural frequency) enhances both oscillation amplitude and electric voltage. It has been also found that, depending on the parametric excitation frequency, the harvested electrical power can be amplified in 70% when compared to the case under no parametric excitation.     

基于统一模型的船舶迎浪参数横摇数值预报及其舵减摇研究

国际海事组织（IMO）正致力于第二代完整稳性规范的制定,而参数横摇一直是船舶动态完整稳性研究的热点。文章采用考虑船舶操纵性和耐波性运动耦合的统一模型对迎浪规则波下的船舶参数横摇运动进行了时域数值模拟。在时域模型中,六自由度耐波性运动辐射绕射力采用切片理论计算,并由脉冲响应函数法转化到时域。非线性回复力和入射波力采用瞬时湿表面压力积分方法计算。操纵性运动基于MMG模型,依据统一理论将操纵性与耐波性运动进行耦合计算。文中先应用简化三自由度模型对三艘集装箱船进行了参数横摇样船计算,并进行了初步的模型实验验证,依据结果对比分析了横摇惯性矩、初稳性高和方形系数对参数横摇的影响。基于统一模型分析了操纵性运动对参数横摇的影响,并进行了参数横摇舵减摇研究。     

An investigation of different methods for the prevention of parametric rolling

The parametric rolling of modern containerships is emerging as a serious problem, to the extent that its effects warrant a study into its prevention. In light of this, two methods for reduction of parametric rolling are proposed and examined by physical model experiments. The first is a sponson attached to the side of a ship, the purpose being to decrease the rate of change of the rollrestoring moment. The second is an antirolling tank to increase roll damping. By conducting free-running model experiments for a 6600-TEU post-Panamax container ship with sponsons under typical parametric rolling conditions, it was found that the sponsons could decrease the magnitude of parametric rolling. The antirolling tank could prevent parametric rolling completely in certain conditions, even in severe head seas. Using the damping coefficients from experimentally derived data of a model ship with an antiroll tank, a numerical simulation was established. The numerical model was then compared with the free-running model experiments. The results indicated that the numerical model could qualitatively verify the experimental results. Finally, an attempt to optimise the size of an antirolling tank for preventing parametric rolling for the subject post-Panamax container ship in the North Pacific Ocean is presented.     

载人潜水器概念设计中的系统集成模型(英文)

在载人潜水器的概念设计阶段,开展系统参数化分析来研究设计变量变化对潜水器性能影响以及多学科优化设计方法在潜水器上的应用是十分有价值的.然而,对于系统参数化分析和多学科设计优化应用所需要的潜水器数学模型,这方面的研究却比较少.为了解决这一问题,该文以某载人潜水器为对象,示范如何建立一个包含有六个模块的载人潜水器系统集成模型,它们分别是艇型模块、阻力模块、能源模块、结构模块、重量模块和稳定性模块.通过设计结构矩阵的应用,发现载人潜水器的概念设计是一个顺序执行的过程,并且属于弱耦合设计问题.     

Parametric roll mitigation using rudder control

Severe roll angles can be developed by parametric excitation in relatively moderate weather without any apparent pre-warning for the crew onboard. In this study the prospect of using rudder control to mitigate parametric roll was investigated using multi-degree of freedom simulations. A typical modern Pure Car and Truck Carrier was considered and modelled by coupling a roll model with a planar motion manoeuvring model. The combined model was calibrated using in-service, full-scale trials and model tests. Irregular variations of the metacentric height were applied to simulate recorded, full-scale events of parametric roll that have occurred with the considered design. These simulations with rudder roll control showed promising results and demonstrate that the approach could be very efficient for mitigation of parametric roll.     

一种海底小目标近距离探测系统及试验研究

随着水下航行器技术的发展及探雷等特殊场合的需求,利用水下小平台探测海底小目标的方式逐渐受到重视,本文依据参量发射阵理论,结合参量阵的优势、截断参量阵的特点,设计了一种应用于海底小目标近距离探测的系统,测试该探测系统在近距离的特性,进行沉底及掩埋目标的探测实验,结果表明,该参量阵系统能够实现海底小目标近距离探测,在现有条件下所做的探索工作具有一定的工程参考价值.     

基于UG二次开发的折叠式舱口盖参数化设计

文章以折叠式舱口盖为研究对象,结合UG／Open GRIP高效、便捷、交互性能强的编程特点和UG／Open API操作简单、控制用户界面方便的优势,依托UG／Open UIStyler制作灵活、多样的人性化界面和UG／OpenMenuScript生成用户菜单,在对折叠式舱口盖结构分析的基础上,引入UG二次开发技术对折叠式舱口盖进行参数化建模系统设计,达到改变折叠式舱口盖部件参数值输入就能迅速建立新模型的目的。经过对参数化建模系统程序调试,系统能够正确、简便、迅速完成折叠式舱口盖部件参数化建模功能。该系统减少了折叠式舱口盖设计周期,提高了设计效率,为折叠式舱口盖参数化建模设计提供参考依据。     

大型集装箱船参数横摇模型试验和数值模拟研究

以4000TEU集装箱船为研究对象,通过系列自航模型试验,确定其在迎浪规则波中发生参数横摇的限界。试验结果显示：在迎浪规则波中,参数横摇通常发生在波浪遭遇周期为横摇固有周期一半的附近;对应不同遭遇频率时参数横摇的发生,存在一个临界波高;航速的增加和舭龙骨的安装将使参数横摇发生的临界波高增加;当有初始干扰时,参数横摇发生的临界波高较小。而且,数值模拟结果与模型试验结果比较吻合。     

参激振动对顺应式垂直通路立管涡激振动的影响

顺应式垂直通路立管(CVAR)是目前处于研究阶段的一种新型的立管类型,在海流作用下产生涡激振动,在平台垂荡运动作用下产生参数激励振动。为了研究参数激励的影响,本文引入尾流振子模型模拟漩涡脱落对立管的作用,同时考虑浮式平台升沉运动产生的参数激励,建立了CVAR参激-涡激联合振动方程,获取联合作用下的动力响应,并与纯涡激振动响应进行对比。结果表明,在相同的流速下CVAR中部涡激振动幅值最大,流速的增大会导致涡激振动的频率增大,发生高阶锁振,高阶锁振振动幅值比低阶锁振振动幅值小。考虑参数激励之后,较纯涡激振动而言,立管的振动幅值增大;当参激频率与涡激振动频率接近时,立管的振动幅值最大。     

参数横摇下大型集装箱船外飘砰击的近似计算方法（英文）

Since the research of flare slamming prediction is seldom when parametric rolling happens, we present an efficient approximation method for flare slamming analysis of large container ships in parametric rolling conditions. We adopt a 6-DOF weakly nonlinear time domain model to predict the ship motions of parametric rolling conditions. Unlike previous flare slamming analysis, our proposed method takes roll motion into account to calculate the impact angle and relative vertical velocity between ship sections on the bow flare and wave surface. We use the Wagner model to analyze the slamming impact forces and the slamming occurrence probability. Through numerical simulations, we investigate the maximum flare slamming pressures of a container ship for different speeds and wave conditions. To further clarify the mechanism of flare slamming phenomena in parametric rolling conditions, we also conduct real-time simulations to determine the relationship between slamming pressure and 3-DOF motions, namely roll, pitch, and heave.