Reduction of emissions with propane addition to a diesel engine

Recent studies on dual-fuel combustion in compression-ignition (CI) engines, also known as diesel engines, fall into two categories. In the first category are studies focused on the addition of small amounts of gaseous fuel to CI engines. In these studies, gaseous fuel is regarded as a secondary fuel and diesel fuel is regarded as the main fuel for combustion. The objectives of these studies typically involve reducing particulate matter (PM) emissions by using gaseous fuel as a partial substitution for diesel fuel. However, the addition of gaseous fuel raises the combustion temperature, which increases emissions of nitrogen oxides (NO_x). In the second category are studies focused on reactivity-controlled compression-ignition (RCCI) combustion. RCCI combustion can be implemented by early diesel injection with a large amount of low-reactivity fuel such as gasoline or gaseous fuel. Although RCCI combustion promises lower NO_x and PM emissions and higher thermal efficiency than conventional diesel combustion, it requires a higher intake pressure (usually more than 1.7 bars) to maintain a lean fuel mixture. Therefore, in this study, practical applications of dual-fuel combustion with a low air-fuel ratio (AFR), which implies a low intake pressure, were systemically evaluated using propane in a diesel engine. The characteristics of dualfuel combustion for high and low AFRs were first evaluated. The proportion of propane used for four different operating conditions was then increased to decrease emissions and to identify the optimal condition for dual-fuel combustion. Although the four operating conditions differ, the AFR was maintained at 20 (? approximately equal to 0.72) and the 50% mass fraction burned (MFB 50) was also fixed. The results show that dual-fuel combustion can reduce NO_x and PM emissions in comparison to conventional diesel combustion.     

Exhaust emissions and its control methods in compression ignition engines: A review

Extensive usage of automobiles has certain disadvantages and one of them is its negative effect on environment. Carbon dioxide (CO₂), carbon monoxide (CO), hydrocarbons (HC), oxides of nitrogen (NO_x), sulphur dioxide (SO₂) and particulate matter (PM) come out as harmful products during incomplete combustion from internal combustion (IC) engines. As these substances affect human health, regulatory bodies impose increasingly stringent restrictions on the level of emissions coming out from IC engines. This trend suggests the urgent need for the investigation of all aspects relevant to emissions. It is required to modify existing engine technologies and to develop a better after-treatment system to achieve the upcoming emission norms. Diesel engines are generally preferred over gasoline engines due to their undisputed benefit of fuel economy and higher torque output. However, diesel engines produce higher emissions, particularly NO_x and PM. Aftertreatment systems are costly and occupy more space, hence, in-cylinder solutions are preferred in reducing emissions. Exhaust gas recirculation (EGR) technology has been utilized previously to reduce NO_x. Though it is quite successful for small engines, problem persists with large bore engines and with high rate of EGR. EGR helps in reducing NO_x, but increases particulate emissions and fuel consumption. Many in-cylinder solutions such as lower compression ratios, modified injection characteristics, improved air intake system etc. are required along with EGR to accomplish the future emission norms. Modern combustion techniques such as low temperature combustion (LTC), homogeneous charge compression ignition (HCCI), premixed charge compression ignition (PCCI) etc. would be helpful for reducing the exhaust emissions and improving the engine performance. However, controlling of autoignition timing and achieving wider operating range are the major challenges with these techniques. A comprehensive review of diesel engine performance and emission characteristics is given in this paper.     

Effect of operating parameters on diesel/propane dual fuel premixed compression ignition in a diesel engine

In this research, the effects of three operating parameters (Diesel injection timing, propane ratio, and exhaust gas recirculation (EGR) rates) in a diesel-propane dual fuel combustion were investigated. The characteristics of dual-fuel combustion were analyzed by engine parameters, such as emission levels (Nitrogen oxides (NO_x) and particulate matter (PM)), gross indicated thermal efficiency (GIE) and gross IMEP Coefficient of Variance (CoV). Based on the results, improving operating strategies of the four main operating points were conducted for dual-fuel PCCI combustion with restrictions on the emissions and the maximum pressure rise rate. The NOx emission was restricted to below 0.21 g/kWh in terms of the indicated specific NO_x (ISNO_x), PM was restricted to under 0.2 FSN, and the maximum pressure rise rate (MPRR) was restricted to 10 bar/deg. Dual-fuel PCI combustion can be available with low NO_x, PM emission and the maximum pressure rise rate in relatively low load condition. However, exceeding of PM and MPRR regulation was occurred in high load condition, therefore, design of optimal piston shape for early diesel injection and modification of hardware optimizing for dual-fuel combustion should be taken into consideration.     

Effect of UWS injection at low exhaust gas temperature on NO<Subscript>x</Subscript> removal efficiency of diesel engine

Urea-SCR systems have been widely used in diesel vehicles according to the strengthened NO_x (Nitrogen Oxides) emission standard. The NO_x removal efficiencies of the latest well optimized urea-SCR system are above 90 % at moderate exhaust gas temperature of 250 ~ 450 °C. However, a large amount of NO_x is emitted from diesel vehicles at cold start or urban driving conditions, when the exhaust gas temperature is not high enough for SCR catalyst activation. Although many researchs have been stuied to improve NO_x conversion efficiency at these low temperature conditions, it is still one of important technical issues. In this study, the effect of UWS injection at low exhaust gas temperature conditions is studied. This study uses a 3.4 L diesel engine equipped with a commertial urea SCR system. As a result, it is found that about 5 % of NO_x removal efficiency is improved in the NRTC test when UWS injection starts at the SCR inlet temperature of 150 °C compared to 200 °C. It is also found that urea deposits can be formed on the wall of exhaust pipe, when the local wall temperature is lower than temperature of urea decomposition.     

Study of the effects on exhaust emissions in direct injection diesel engines: Effects of fuel injection system,distillation properties and cetane number

The effect of injection nozzle, diesel fuel density (volatility) and cetane number on diesel exhaust emissions were investigated. Decreasing injection nozzle hole diameter decreases PM emission. However, a small nozzle hole increases NO_x emission and decreases the effect of fuel on PM emission. Decreasing fuel density is effective for reduction of NO_x emission. But the effect is smaller than that of nozzle hole diameter and injection pressure. Furthermore injection timing retardation decreases the effect of fuel density on NO_x emission.     

Urea-SCR system optimization with various combinations of mixer types and decomposition pipe lengths

The demand for NO_x after-treatment system has increased dramatically due to the stricter NO_x emission regulations for diesel vehicles. The urea-SCR system is one of the NO_x after-treatment methods found to be quite effective to meet the regulation requirement enforced by various authorities including the Euro-6. In order to develop an effective urea-SCR system, it is critical to establish an even distribution of reductant over the catalyst surface since this favorable distribution can increase reduction reaction and in turn, improve NO_x conversion efficiencies. In the current study, a number of design variations of the urea-SCR system which included two mixer types and three decomposition pipe lengths, were evaluated systematically using CFD analysis and experimental measurements. The purpose of the CFD analysis was to estimate the distribution of reductant within the urea-SCR system with a specific configuration and the purpose of the engine emission test was to measure the amount of NO_x reduction, respectively. The results from the systematic analysis revealed the relation between the reductant distribution over the SCR and the performance of the NO_x reduction.     

Model-based control system design in a urea-SCR aftertreatment system based on NH3 sensor feedback

This paper presents preliminary control system simulation results in a urea-selective catalytic reduction (SCR) aftertreatment system based on NH₃ sensor feedback. A four-state control-oriented lumped parameter model is used to analyze the controllability and observability properties of the urea-SCR plant. A model-based estimator is designed via simulation and a control system is developed with design based on a sliding mode control framework. The control system based on NH₃ sensor feedback is analyzed via simulation by comparing it to a control system developed based on NO_x sensor feedback. Simulation results show that the NH₃ sensor-based strategy performs very similarly in comparison to a NO_x sensor-based strategy. The control system performance metrics for NO_x index, urea index, urea usage, and NH₃ slip suggest that the NO_x sensor can be a potential alternative to a NO_x sensor for urea-SCR control applications.     

Experimental investigation and comparison of nanoparticle emission characteristics in light-duty vehicles for two different fuels

In recent years, particle number emissions rather than particulate mass emissions in automotive engines have become the subject with controversial discussions. Recent results from studies of health effects imply that it is possible that particulate mass does not properly correlate with the variety of health effects attributed to engine exhaust. The concern is now focusing on nano-sized particles emitted from I. C. engines. In this study, particulate mass and particle number concentration emitted from light-duty vehicles were investigated for a better understanding of the characteristics of the engine PM from different types of fuels, such as gasoline and diesel fuel. Engine nano-particle mass and size distributions of four test vehicles were measured by a condensation particle counter system, which is recommended by the particle measurement program in Europe (PMP), at the end of a dilution tunnel along a NEDC test mode on a chassis dynamometer. We found that particle number concentrations of diesel passenger vehicles with DPF system are lower than gasoline passenger vehicles, but PM mass has some similar values. However, in diesel vehicles with DPF system, PM mass and particle number concentrations were greatly influenced by PM regeneration. Particle emissions in light-duty vehicles emitted about 90% at the ECE15 cycle in NEDC test mode, regardless of vehicle fuel type. Particle emissions at the early cold condition of engine were highly emitted in the test mode.     

Review on characterization of nano-particle emissions and PM morphology from internal combustion engines: Part 2

This paper presents a review of the characterization of physical properties, morphology, and nanostructure of particulate emissions from internal combustion engines. Because of their convenience and readiness of measurement, various on-line commercial instruments have been used to measure the mass, number, and size distribution of nano-particles from different engines. However, these on-line commercial instruments have inherent limitations in detailed analysis of chemical and physical properties, morphology, and nanostructure of engine soot agglomerates, information that is necessary to understand the soot formation process in engine combustion, soot particle behavior in after-treatment systems, and health impacts of the nano-particles. For these reasons, several measurement techniques used in the carbon research field, i.e., highresolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), and Raman spectroscopy, were used for analysis of engine particulate matter (PM). This review covers a brief introduction of several measurement techniques and previous results from engine nano-particle characterization studies using those techniques.     

基于改善柴油机排放的燃烧过程优化措施

改善柴油机排放的核心是对燃烧过程进行优化,通过改善燃烧过程来降低柴油机排放是当前柴油机研究中的重要课题。本文主要从优化进气系统、优化喷油系统、优化燃烧室结构、燃料的改质及优化润滑系统五个方面进行分析,综合这些相互制约的优化措施优化柴油机的燃烧过程,降低颗粒物质PM和NOx的直接排放。     

Review on characterization of nano-particle emissions and PM morphology from internal combustion engines: Part 1

This paper is review of the characterization of exhaust particles from state-of-the-art internal combustion engines. We primarily focus on identifying the physical and chemical properties of nano-particles, i.e., the concentration, size distribution, and particulate matter (PM) morphology. Stringent emissions regulations of the Euro 6 and the LEV III require a substantial reduction in the PM emissions from vehicles, and improvements in human health effects. Advances in powertrains with sophisticated engine control strategies and engine after-treatment technologies have significantly improved PM emission levels, motivating the development of new particle measurement instruments and chemical analysis procedures. In this paper, recent research trends are reviewed for physical and chemical PM characterization methods for gasoline and diesel fueled engines under various vehicle certification cycles and real-world driving conditions. The effects of engine technologies, fuels, and engine lubricant oils on exhaust PM morphology and compositions are also discussed.     

Computational study on the effects of volume ratio of DOC/DPF and catalyst loading on the PM and NOx emission control for heavy-duty diesel engines

The use of a diesel particulate filter (DPF) in a diesel aftertreatment system has proven to be an effective and efficient method for removing particulate matter (PM) in order to meet more stringent emission regulations without hurting engine performance. One of the favorable PM regeneration technologies is the NO₂-assisted regeneration method due to the capability of continuous regeneration of PM under a much lower temperature than that of thermal regeneration. In the present study, the thermal behavior of the monolith during regeneration and the conversion efficiency of NO₂ from NO with an integrated exhaust system of a diesel oxidation catalyst (DOC) and DPF have been predicted by one-channel numerical simulation. The simulation results of the DOC, DPF, and integrated DOC-DPF models are compared with experimental data to verify the accuracy of the present model for the integrated DOC and DPF modeling. The effects of catalyst loading inside the DOC and the volume ratio between the DOC and DPF on the pressure drop, the conversion efficiency, and the oxidation rate of PM, have been numerically investigated. The results indicate that the case of the volume ratio of ‘DOC/DPF=1.5’ within the same diameter of both monoliths produced close to the maximum conversion efficiency and oxidation rate of PM. Under the engine operating condition of 175 kW at 2200 rpm, 100% load with a displacement of 8.1, approximately 55 g/ft³ of catalyst (Pt) loading inside the DOC with the active Pt surface of 5.3 m²/g_pt was enough to maximize the conversion efficiency and oxidation rate of PM.     

Development of new 4-valve/cylinder small DI diesel engine

Nitrous oxide (NO_x) and the particulate matter contained in the exhaust given off by diesel powered vehicles have been identified as elements responsible for polluting the atmosphere. As such, these emissions have been the targets of increasingly strict emission control regulations. Plans are underway to introduce regulations that are even stricter some time early in the next century. The advanced thermal efficiency offered by diesel engines is a feature clearly desired for its potential contribution toward energy conservation and the reduction of global warming. Research and development on the highly thermal-efficient direct-injection diesel engine are progressing at a rapid pace in Europe where introduction of a carbon dioxide tax is under consideration.     

柴油机排气微粒中可溶有机组分的分析

采用超声洗脱法,分离出柴油机排气微粒(PM)中的可溶有机组分(SOF)。利用色谱—质谱联用技术对SOF的成分进行了分析。结果表明,SOF中最大的组分为烷烃,其次是芳香烃;烷烃中大部分为直链烷烃,芳香烃以萘族和菲族等多环芳香烃为主。给出了微粒SOF中烷烃和芳香烃等有机成分在不同工况下所占有的比例,以及芳香烃中主要有机组分的百分含量。     

Sliding-mode observer for urea-selective catalytic reduction (SCR) mid-catalyst ammonia concentration estimation

This paper presents an observer design for SCR mid-catalyst ammonia concentration estimation using tailpipe NO_x and ammonia sensors. Urea-SCR has been popularly used by Diesel engine powered vehicles to reduce NO_x emissions in recent years. It utilizes ammonia, converted from urea injected at upstream of the catalyst, as the reductant to catalytically convert NO_x emissions to nitrogen. To simultaneously achieve high SCR NO_x conversion efficiency and low tailpipe ammonia slip, it is desirable to control the ammonia storage distribution along the SCR catalyst. Such a control method, however, requires a mid-catalyst ammonia sensor. The observer developed in this paper can replace such a mid-catalyst ammonia sensor and be used for SCR catalyst ammonia distribution control as well as serves for fault diagnosis purpose of the mid-catalyst ammonia sensor. The stability of the observer was shown based on the sliding mode approach and analyzed by simulations. Experimental validation of the observer was also conducted based on a medium-duty Diesel engine two-catalyst SCR system setup with emission sensors.     

Heat exchanger/catalytic system for reducing the exhaust emissions from diesel engines

A system has been researched over the past 3 years for reducing the exhaust pollutants from diesel engines for light commercial vehicles. The system researched achieves Euro 6 standards for reduction of polluting gases (CO, HC, PM, NO). It consists of 4 main sections: 1. A heater and heat exchanger (HE); 2. A CO/HC oxidising catalyst (D°C); 3. Pt catalyst on a diesel particulate filter (DPF); 4. A NO reducing reaction (SCR) within the DPF. The system operates as follows. The exhaust gas contains oxidising gases, namely both O₂ and NO₂. The levels of CO and HC are oxidised by O₂ to CO₂ for temperatures above 200°C. Carbon (PM) is oxidised to CO₂ by NO₂ but requires a temperature above 250°C. The operating exhaust temperature of 300°C is ideal for the removal of NO by using the Pt catalyst and the CO generated within the DPF. The heater is required to be able to raise the exhaust temperature at any time to 300°C in order to optimise the performance of the system, since diesel engine exhaust temperatures vary between 160°C (slow speeds) to 350°C (high speeds). Considerable heat is required (??3 kW) to maintain the exhaust gas for a 2l engine at 300°C for engine idle conditions. Therefore a heat exchanger is required to re-circulate the input heat and thereby reduce the maximum power consumption to a maximum of 500W over the engine full operating test cycle. This energy is supplied by the engine battery and alternator. Experimental results have been obtained for the exhaust from a Kubota diesel engine and the reductions in exhaust emissions of 83% (CO/ HC), 58% (NOx) and 99% (PM) were obtained. The PM was continuously cleaned so that there was no build up of back pressure.     

Evaluation and visualization of stratified ultra-lean combustion characteristics in a spray-guided type gasoline direct-injection engine

To comply with reinforced emission regulations for harmful exhaust gases, including carbon dioxide (CO₂) emitted as a greenhouse gas, improved technologies for reducing CO₂ and fuel consumption are being developed. Stable lean combustion, which has the advantage of improved fuel economy and reduced emission levels, can be achieved using a sprayguided-type direct-injection (DI) combustion system. The system comprises a centrally mounted injector and closely positioned spark plugs, which ensure the combustion reliability of a stratified mixture under ultra-lean conditions. The aim of this study is to investigate the combustion and emission characteristics of a lean-burn gasoline DI engine. At an excess air ratio of 4.0, approximately 23% improvement in fuel economy was achieved through optimal event timing, which was delayed for injection and advanced for ignition, compared to that under stoichiometric conditions, while NO_x and HC emissions increased. The combustion characteristics of a stratified mixture in a spray-guided-type DI system were similar to those in DI diesel engines, resulting in smoke generation and difficulty in three-way catalystutilization. Although a different operating strategy might decrease fuel consumption, it will not be helpful in reducing NO_x and smoke emissions; therefore, alternatives should be pursued to achieve compliance with emission regulations.     

Adaptation Strategy for Exhaust Gas Recirculation and Common Rail Pressure to Improve Transient Torque Response in Diesel Engines

Fuel injection limitation algorithms are widely used to reduce particulate matter (PM) emissions under transient states in diesel engines. However, the limited injection quantity leads to a decrease in the engine torque response under transient states. To overcome this issue, this study proposes an adaptation strategy for exhaust gas recirculation (EGR) and common rail pressure combined with a fuel injection limitation algorithm. The proposed control algorithm consists of three parts: fuel injection limitation, EGR adaptation, and rail pressure adaptation. The fuel injection quantity is limited by adjusting the exhaust burned gas rate, which is predicted based on various intake air states like air mass flow and EGR mass flow. The control algorithm for EGR and rail pressure was designed to manipulate the set-points of the EGR and rail pressure when the fuel injection limitation is activated. The EGR controller decreases the EGR gas flow rate to rapidly supply fresh air under transient states. The rail pressure controller increases the rail pressure set-point to generate a well-mixed air-fuel mixture, resulting in an enhancement in engine torque under transient states. The proposed adaptation strategy was validated through engine experiments. These experiments showed that PM emissions were reduced by up to 11.2 %, and the engine torque was enhanced by 5.4 % under transient states compared to the injection limitation strategy without adaptation.     

Estimation of soot oxidation rate in DPF under carbon and non-carbon based particulate matter accumulated condition

By high particulate matter(PM) reduction performance, diesel particulate filter(DPF) is applied to almost all of modern HSDI diesel engine. PM emitted from diesel engine is consist of carbon based and non-carbon based material. Representative carbon based PM is soot. Non-carbon based PM is produced by wear of engine and exhaust component, combustion of lubrication oil and sulphur in fuel. Accumulation of non-carbon based PM affects pressure difference of DPF and thus accuracy of soot mass estimation in DPF can be lowered during normal and regeneration condition when the pressure difference caused by non-carbon based PM is not recognized correctly. Also unevenly accumulated PM inside of DPF can produce locally different exhaust gas temperature and thus it can lower accuracy of soot mass estimation during regeneration. This study focuses on estimation of soot oxidation rate not by conventional pressure difference but by exhaust gas analysis at up and downstream of DPF. Results, strong correlations between CO₂ -fuel mass ratio and soot oxidation was observed.     

掺烧比对P50/甲醇双燃料发动机燃烧与排放的影响

燃料富氧重整和双燃料燃烧模式是改善燃烧过程和降低颗粒物排放的重要方法.在一台四缸增压中冷的高压共轨柴油机上,采用进气道喷射甲醇、缸内喷射P50(50％体积比例柴油与50％体积比例PODE)的双燃料模式,研究掺混比对P50/甲醇双燃料发动机燃烧与排放特性的影响.研究结果表明:相比于纯柴油模式,P50及P50/甲醇双燃料燃...