共查询到18条相似文献,搜索用时 156 毫秒
1.
为了解决混合动力系统动力耦合的响应性和舒适性问题,建立混动离合器C0起动发动机过程和并联动力输出模式下的功率流模型。对C0起动发动机的控制过程进行仿真分析,针对C0的起动扭矩和电机的输出扭矩在时间和空间上的匹配问题,提出以换挡离合器的滑摩控制来进行缓冲的策略。为了实现稳定精确的发动机起动控制,消除各自的扭矩控制、液压系统特性的误差,提出C0离合器起动发动机的自适应控制和B1离合器滑摩自适应控制,以换挡离合器滑差和发动机转速的超调量为监控对象,对C0离合器各阶段压力控制参数进行自适应调整,以优化发动机起动过程。研究结果表明:通过换挡离合器的滑摩控制可以很好地解决C0离合器扭矩和电机扭矩的匹配问题,即使在换挡过程中对发动机起动也能保证良好的舒适性,并控制过程时间在1.5 s内;在整车试验过程中,通过对C0压力的自适应调整,发动机转速的超调和起动冲击问题均可以得到有效解决。 相似文献
2.
3.
4.
混合动力汽车通过发动机和电机两种动力源实现多种驱动模式,不同动力源的切换对整车动力性能和驾驶性能有着重要影响。在四轮驱动混合动力汽车的基础上,针对模式切换过程中不同动力源响应性差异造成驾驶性能变差的问题,以纯电动向混合驱动模式切换过程为研究对象,提出了以离合器、电机和发动机为控制对象的协调控制策略,通过控制离合器接合压力并结合电机定转矩补偿控制,同时对发动机转速进行PID闭环控制。台架和实车试验结果表明:该控制策略能够快速平稳地实现驱动模式切换,提高了整车驾驶性能。 相似文献
5.
6.
(接上期)2.离合器压力控制(图10)PCM驱动换挡电磁阀A和B控制超速传动离合器压力。PCM接收来自各传感器、开关和控制单元的输入信号,然后处理数据,并确定驾驶模式。当驾驶模式从HV驾驶模式转移到发动机驾驶模式时,PCM驱动换挡电磁阀B,使超速传动离合器运作。为了减少在啮合过程中产生的冲击,PCM控制发动机和牵引电机的转速。 相似文献
7.
《汽车工程学报》2017,(4)
研究了P2结构混合动力传动系统通过IMG电机和混动离合器对发动机的启动控制。建立了与发动机启动过程相关的关键物理模型和控制策略模型,并分析了模型物理参数和控制参数对启动性能的影响。通过仿真发现,发动机的启动转速、混动离合器的压力控制都会对发动机的启动时间和舒适性造成影响。在发动机启动过程中,对换挡离合器采用滑摩的控制方式来消除混动离合器压力与控制转矩不匹配时产生的冲击。通过对发动机转速的超调量进行监控,动态地自适应调整混动离合器的控制压力以保证控制效果的一致性。为了兼顾不同油门下对发动机启动过程的动力性和舒适性的要求,通过离合器压力控制,对小油门工况采用舒适型启动控制,对大油门工况采用动力型启动控制。整车的试验结果对离合器启动发动机的控制过程进行了验证,从启动时间和舒适性角度满足整车对启动性能的要求。 相似文献
8.
9.
10.
2 挡油路
变速器以1挡运行后当满足升2挡条件时,控制单元便发出2挡换挡指令信息,此时真实的输出是这样的:首先第一个动作要完成K1离合器和K2离合器的交替切换过程,为了避免换挡点瞬间出现动力流中断现象,因此K1和K2在油路上的切换是通过重叠方式来实现的,也就是K1离合器在释放过程和K2离合器在接合过程中出现一个短暂的重叠过程,它是发生在重叠扭矩不大、重叠时间很短的情况下,因此只需适当的调整下发动机输出扭矩,这样就不会形成扭矩的干预而引起的换挡品质下降;完成离合器交接后就像传递接力棒一样,K2离合器替代K1离合器在传递发动机扭矩,此时动力流在2挡传动比上完成(如图719所示),完成这个动作过程后控制单元必须尽快完成下一个预选挡的切换过程,那就是首先要把1/3挡同步器由1挡侧切换到3挡侧(可以看图720). 相似文献
11.
并联式混合动力汽车模式切换时离合器会介入传动系统,容易引起较明显的冲击感,是影响整车驾驶舒适性的主要因素。为此,提出了基于离合器双模糊和电机转矩协调的模式切换控制策略。首先建立混合动力汽车模式切换过程的动力学模型,以减小离合器滑磨功为目标,对模式切换时的离合器接合过程进行划分;其次,结合混合动力汽车模式切换的基本要求和驾驶意图,制定离合器双模糊控制策略,分别对滑摩阶段的接合时长和转矩同步阶段的压力变化率进行控制;然后以离合器滑磨功和整车冲击度为优化目标,采用二次型最优控制算法对滑摩阶段的接合压力进行优化,从而获取模式切换过程中离合器的最优接合压力轨迹;在此基础上,通过实时计算离合器传递转矩,根据电机转矩响应快的特点,制定电机转矩协调控制策略;最后,基于某混合动力试验样车,在底盘测功机上分别进行缓加速、中等加速和急加速下的模式切换试验,对所提出的控制策略进行验证。试验结果表明:该策略能较好地反映驾驶人驾驶意图,保证离合器的使用寿命,所产生的整车冲击度均处于合理范围之内,改善了整车模式切换过程中的驾驶舒适性。 相似文献
12.
Kyuhyun Sim Sang-Min Oh Choul Namkoong Ji-Suk Lee Kwan-Soo Han Sung-Ho Hwang 《International Journal of Automotive Technology》2017,18(5):901-909
The plug-in hybrid electric vehicle (PHEV) has various driving modes used in both internal combustion engine and electric motors. The EV mode uses only an electric motor and the HEV mode uses both an engine and an electric motor. Specifically, when the PHEV of a pre-transmission parallel hybrid structure performs mode changing, its engine clutch is either engaged or disengaged, which is important in terms of ride comfort. In this paper, to enhance the mode changing process for the clutch engagement, a PHEV performance simulator is developed using MATLAB/Simulink based on system dynamics and experiment data. Vehicle driving analysis is carried out of the control logic and properties of the mode changing. A compensated torque is applied during the mode change. This results in the rapid speed synchronization with the clutch although the trade-off relationship of the mode change. In addition, the mode changing is conducted through the transmission shifting process to rapidly synchronize with speed. The control strategy implemented in this study is shown to improve the drivability and energy efficiency of a PHEV. 相似文献
13.
14.
Z. Zhong G. Kong Z. Yu X. Xin X. Chen 《International Journal of Automotive Technology》2012,13(3):487-496
The automated mechanical transmission (AMT) is gaining popularity in the automotive industry, due to its combination of the
advantages of mechanical transmissions (MT) and automatic transmissions (AT) in terms of fuel consumption, low cost, improved
driving comfort and shifting quality. However, the inherent structural characteristics of the AMT lead to disadvantages, including
excessive wear of the clutch plates and jerk and traction interruption during the shift process, that severely affect its
popularity in the automatic transmission industry. The emerging technology of shifting control without the use of the clutch
is a promising way to improve the shifting transients of AMTs. This paper proposes a control algorithm that combines speed
and torque control of the AMT vehicle powertrain to achieve shifting control without using the clutch. The key technologies
of accurate engine torque and speed control and rapid position control of the shift actuators are described in detail. To
realize accurate engine speed control, a combined control algorithm based on feed-forward, bang-bang and PID control is adopted.
Additionally, an optimized closed-loop position control algorithm based on LQR is proposed for the shift actuators. The coordinated
control algorithm based on engine and shift actuator control is described in detail and validated on a test vehicle equipped
with an AMT. The results show that the coordinated control algorithm can achieve shifting control without the use of the clutch
to improve driving comfort significantly, reduce shift transients and extend the service life of the clutch. 相似文献
15.
16.
17.