Multi-modal traffic signal control with priority,signal actuation and coordination

Both coordinated-actuated signal control systems and signal priority control systems have been widely deployed for the last few decades. However, these two control systems are often conflicting with each due to different control objectives. This paper aims to address the conflicting issues between actuated-coordination and multi-modal priority control. Enabled by vehicle-to-infrastructure (v2i) communication in Connected Vehicle Systems, priority eligible vehicles, such as emergency vehicles, transit buses, commercial trucks, and pedestrians are able to send request for priority messages to a traffic signal controller when approaching a signalized intersection. It is likely that multiple vehicles and pedestrians will send requests such that there may be multiple active requests at the same time. A request-based mixed-integer linear program (MILP) is formulated that explicitly accommodate multiple priority requests from different modes of vehicles and pedestrians while simultaneously considering coordination and vehicle actuation. Signal coordination is achieved by integrating virtual coordination requests for priority in the formulation. A penalty is added to the objective function when the signal coordination is not fulfilled. This “soft” signal coordination allows the signal plan to adjust itself to serve multiple priority requests that may be from different modes. The priority-optimal signal timing is responsive to real-time actuations of non-priority demand by allowing phases to extend and gap out using traditional vehicle actuation logic. The proposed control method is compared with state-of-practice transit signal priority (TSP) both under the optimized signal timing plans using microscopic traffic simulation. The simulation experiments show that the proposed control model is able to reduce average bus delay, average pedestrian delay, and average passenger car delay, especially for highly congested condition with a high frequency of transit vehicle priority requests.     

An analytical model to conduct a person-based evaluation of transit preferential treatments on signalized arterials

The complexities of urban transportation networks where multiple modes with different characteristics and needs travel in combination with constraints on space and funding make the sustainable management of these systems a challenge. In order to improve transit service, space (e.g., dedicated bus lanes) and time (e.g., transit signal priority strategies) Transit Preferential Treatments (TPT) are deployed to improve transit operations. The objective of this paper is to develop an analytical model that allows for a person-based evaluation of alternative TPTs when considered individually and in combination. In particular, the analytical model is developed to assess person delay and person discharge flow at any intersection that is part of a signalized arterial, where auto arrivals are in platoons. The performance of TPTs is evaluated using both the analytical model and through microsimulation tests on two intersections of San Pablo Avenue in Berkeley, CA. Space TPTs such as dedicated bus lanes and queue jumper lanes are beneficial in reducing bus person delay when provided in addition to the existing lanes; however, the effectiveness of time TPTs such as green extension depends on the level of auto demand in combination with signal settings. Changes in person discharge flow are not significant for any of the treatments tested with the exception of the bus lane substitution with and without green extension, which led to a significant decrease in person discharge flow. Increased bus frequency increases the effectiveness of transit signal priority in reducing total and bus person delay. The analytical model results produce ranking outcomes that are comparable with the microsimulation ones and therefore, the model may be used for a quantitative evaluation of TPTs without the need for data intensive and time consuming calibration efforts required for microsimulation models. The developed model can be used to guide infrastructure and investment decisions on where such TPTs should be implemented and under what conditions space TPTs should be combined with time TPTs to improve person mobility.     

Self-organizing traffic signals using secondary extension and dynamic coordination

Actuated traffic signal control logic has many advantages because of its responsiveness to traffic demands, short cycles, effective use of capacity leading to and recovering from oversaturation, and amenability to aggressive transit priority. Its main drawback has been its inability to provide good progression along arterials. However, the traditional way of providing progression along arterials, coordinated–actuated control with a common, fixed cycle length, has many drawbacks stemming from its long cycle lengths, inflexibility in recovering from priority interruptions, and ineffective use of capacity during periods of oversaturation. This research explores a new paradigm for traffic signal control, “self-organizing signals,” based on local actuated control but with some additional rules that create coordination mechanisms. The primary new rules proposed are for secondary extensions, in which the green may be held to serve an imminently arriving platoon, and dynamic coordination, in which small groups of closely spaced signals communicate with one another to cycle synchronously with the group’s critical intersection. Simulation tests in VISSIM performed on arterial corridors in Massachusetts and Arizona show overall delay reductions of up to 14% compared to an optimized coordinated–actuated scheme where there is no transit priority, and more than 30% in scenarios with temporary oversaturation. Tests also show that with self-organizing control, transit signal priority can be more effective than with coordinated–actuated control, reducing transit delay by about 60%, or 12 to 14 s per intersection with little impact on traffic delay.     

Integrated optimization of bus priority operations in connected vehicle environment

Most previous works associated with transit signal priority merely focus on the optimization of signal timings, ignoring both bus speed and dwell time at bus stops. This paper presents a novel approach to optimize the holding time at bus stops, signal timings, and bus speed to provide priority to buses at isolated intersections. The objective of the proposed model is to minimize the weighted average vehicle delays of the intersection, which includes both bus delay and impact on nearby intersection traffic, ensuring that buses clear these intersections without being stopped by a red light. A set of formulations are developed to explicitly capture the interaction between bus speed, bus holding time, and transit priority signal timings. Experimental analysis is used to show that the proposed model has minimal negative impacts on general traffic and outperforms the no priority, signal priority only, and signal priority with holding control strategies (no bus speed adjustment) in terms of reducing average bus delays and stops. A sensitivity analysis further demonstrates the potential of the proposed approach to be applied to bus priority control systems in real‐time under different traffic demands, bus stop locations, and maximum speed limits. Copyright © 2016 John Wiley & Sons, Ltd.     

Priority for public transit in Germany

Priority for public transit includes a large variety of measures, including improvements to infrastructure and vehicles. For vehicles, the low floor concept is of particular importance. The central points of priority measures, however, are improvements of traffic control by traffic signals. Here, an improved sensitivity regarding public transit vehicles is the key to a remarkable reduction of factors causing delay. Different techniques for a traffic actuated signal control and different strategies regarding the degree of priority are applied. Thus, especially the reliability of public transit operations is increased. The priority efforts must be embedded in an integrated plan covering the whole urban or metropolitan transportation system.     

An integrated real-time traffic signal system for transit signal priority,incident detection and congestion management

This paper presents a traffic control system that can work standalone to handle various boundary conditions of the recurrent, non-recurrent congestion, transit signal priority and downstream blockage conditions to improve the overall traffic network vehicular productivity and efficiency. The control system uses field detectors’ data to determine the boundary conditions of all incoming and exit links. The developed system is interfaced with CORSIM micro-simulation for rigorous evaluations with different types of signal phase settings. The comparative performance of this control logic is quite satisfactory for some of the most frequently used phase settings in the network with a high number of junctions under highly congested conditions.     

Dependability as a measure of on-time performance of personal rapid transit systems

A comprehensive method for calculating and measuring Dependability of Personal Rapid Transit systems is derived and compared with the more common measure called Availability. Availability is the percentage of all revenue trips that are completed without interruption. It does not take into account the duration of delays of the passengers because of the diffiiculty of gathering the necessary information in conventional transit systems. In PRT systems, vehicle-hours of travel and of delay relate in a statistically simple way to person-hours of travel and of delay. Therefore, in such systems, it is practical to use the performance measure called Dependability that takes into account the inconveince of people as a result of delays. To form a bridge to present practice, it is recommended that both measures be calculated and compared in forthcoming PRT systems. With today's computer systems, this is easily accomplished.     

Mobility and environment improvement of signalized networks through Vehicle-to-Infrastructure (V2I) communications

Traffic signals, even though crucial for safe operations of busy intersections, are one of the leading causes of travel delays in urban settings, as well as the reason why billions of gallons of fuel are burned, and tons of toxic pollutants released to the atmosphere each year by idling engines. Recent advances in cellular networks and dedicated short-range communications make Vehicle-to-Infrastructure (V2I) communications a reality, as individual cars and traffic signals can now be equipped with communication and computing devices. In this paper, we first presented an integrated simulator with V2I, a car-following model and an emission model to simulate the behavior of vehicles at signalized intersections and calculate travel delays in queues, vehicle emissions, and fuel consumption. We then present a hierarchical green driving strategy based on feedback control to smooth stop-and-go traffic in signalized networks, where signals can disseminate traffic signal information and loop detector data to connected vehicles through V2I communications. In this strategy, the control variable is an individual advisory speed limit for each equipped vehicle, which is calculated from its location, signal settings, and traffic conditions. Finally, we quantify the mobility and environment improvements of the green driving strategy with respect to market penetration rates of equipped vehicles, traffic conditions, communication characteristics, location accuracy, and the car-following model itself, both in isolated and non-isolated intersections. In particular, we demonstrate savings of around 15% in travel delays and around 8% in fuel consumption and greenhouse gas emissions. Different from many existing ecodriving strategies in signalized road networks, where vehicles’ speed profiles are totally controlled, our strategy is hierarchical, since only the speed limit is provided, and vehicles still have to follow their leaders. Such a strategy is crucial for maintaining safety with mixed vehicles.     

What do commuters think travel time reliability is worth? Calculating economic value of reducing the frequency and extent of unexpected delays

The measurement of transportation system reliability has become one of the central topics of travel demand studies. A growing literature concerns the measurement of value of travel time reliability which provides a monetary cost of avoiding unpredictable travel time. The goal of this study is to measure commuters’ sensitivities to travel time reliability and their willingness to pay (WTP) to avoid unreliable routes. The preferences are elicited through a pivoted stated preference survey technique. To circumvent the issue of presenting numerical distributions and statistical terms to day-to-day commuters, we use the frequency of delay days as a means of measuring traveler’s sensitivities to travel time reliability. The advantage of using simplified measures to elicit traveler preferences for travel time reliability is that these methods simply compare days with high delay to days with usual travel time. It was found that travelers are not only averse to the amount of unexpected delay but also to the frequency of days with unexpected delays. The paper presents WTP findings for three measures: travel time, frequency embedded travel time, and travel time reliability. The ‘reliability’ increase in WTP for travel time is found to be nearly proportional to the frequency of experiencing unexpected delays. For example, the WTP for mean travel time is calculated at $6.98/h; however, reliability adds $3.27 (about 50 % of $6.98) to avoid unexpected delays ‘5 out of 10 days’. The results of the study would provide valuable inputs to cost-benefit analyses and traffic and revenue studies required for road tolling investment projects.     

Traffic performance of shared lanes at signalized intersections based on cellular automata modeling

Shared lanes at signalized intersections are designed for use by vehicles of different movement directions. Shared lane usage increases the flexibility of assigning lane grouping to accommodate variable traffic volume by direction. However, a shared lane is not always beneficial as it can at time result in blockage that leads to both capacity and safety constraints. This paper establishes a cellular automata model to simulate traffic movements at signalized intersections with shared lanes. Several simulation experiments are carried out both for a single shared lane and for an approach with a shared lane. Simulation of a single shared lane used by straight‐through and right‐turn (as similar to left‐turn in the USA) vehicles suggests that the largest travel delay occurs when traffic volumes (vehicles/lane) of the two movement streams along the shared lane are at about the same level. For a trial lane‐group with a shared lane, when traffic volumes of the two movement streams are quite different, the shared lane usage is not efficient in terms of reduction in traffic delay. The simulation results are able to produce the threshold traffic volume to arrange a shared lane along an approach. Copyright © 2013 John Wiley & Sons, Ltd.     

An optimization method for sustainable traffic control in urban areas

The optimization of traffic signalization in urban areas is formulated as a problem of finding the cycle length, the green times and the offset of traffic signals that minimize an objective function of performance indices. Typical approaches to this optimization problem include the maximization of traffic throughput or the minimization of vehicles’ delays, number of stops, fuel consumption, etc. Dynamic Traffic Assignment (DTA) models are widely used for online and offline applications for efficient deployment of traffic control strategies and the evaluation of traffic management schemes and policies. We propose an optimization method for combining dynamic traffic assignment and network control by minimizing the risk of potential loss induced to travelers by exceeding their budgeted travel time as a result of deployed traffic signal settings, using the Conditional Value-at-Risk model. The proposed methodology can be easily implemented by researchers or practitioners to evaluate their alternative strategies and aid them to choose the alternative with less potential risk. The traffic signal optimization procedure is implemented in TRANSYT-7F and the dynamic propagation and route choice of vehicles is simulated with a mesoscopic dynamic traffic assignment tool (DTALite) with fixed temporal demand and network characteristics. The proposed approach is applied to a reference test network used by many researchers for verification purposes. Numerical experiments provide evidence of the advantages of this optimization method with respect to conventional optimization techniques. The overall benefit to the performance of the network is evaluated with a Conditional Value-at-Risk Analysis where the optimal solution is the one presenting the least risk for ‘guaranteed’ total travel times.     

Passing Bays for Slow Moving Vehicles on Rural Two‐lane Roads

Abstract

Slow‐moving vehicles, including agricultural vehicles, on arterial highways can cause serious delays to other traffic as well as posing an extra safety risk. This paper elaborates on a small‐scale solution for these problems: the passing bay. It investigates the impacts of a passing bay on the total delay for other motorized vehicles, the number of passing manoeuvres and hindered vehicles, and the mean delay per hindered vehicle. The latter is also considered to be an indicator for traffic safety. The calculations are performed for two characteristic trips with a slow‐moving vehicle. The passing bay is an effective solution to reducing delays on arterial highways when two‐way hourly volumes exceed 600–1000 vehicles. The effects depend on the trip length and speed of the slow‐moving vehicle, and on the passing sight distance limitations of the road. A distance of 2–4?km between the passing bays seems an acceptable compromise between the reduction of delay for other motorized vehicles and the extra discomfort and delay for drivers of slow‐moving vehicles. This result also shows that passing bays are not effective in regions where slow‐moving vehicles mainly make trips shorter than this distance.     

The development of taiwan arterial traffic‐adaptive signal control system and its field test: A taiwan experience

This Taiwan traffic‐adaptive arterial signal control model borrowed its traffic flow framework mainly from a British traffic‐adaptive control model with a cyclic traffic progression function, i.e. SCOOT (Split Cycle Office Optimisation Technique). The new arterial control model can take into account delays of both major and minor streets and make real‐time signal timing decisions with optimal two‐way signal offsets, so as to create the best arterial signal operation performance. It has been developed to be an online real‐time software for both simulation testing and field validation. Through simulation, it was found that the performance when operating this newly developed real‐time arterial traffic‐adaptive model was significantly better than when using the optimal fixed‐time arterial timing plan. On the aspect of field testing, three signalized intersections located in East District, Tainan City, Taiwan were selected to be the test sites. Fairly good traffic control performance has been demonstrated in that it can effectively reduce travel delays of the control arterial as a whole. Additional discussions about how to combine travel delay and the total number of vehicle stops into a new control performance index have also been included to make the new traffic‐adaptive model more flexible and reasonable to meet the expectations of different driver groups in the arterial system.     

Tracking a system of shared autonomous vehicles across the Austin,Texas network using agent-based simulation

This study provides a large-scale micro-simulation of transportation patterns in a metropolitan area when relying on a system of shared autonomous vehicles (SAVs). The six-county region of Austin, Texas is used for its land development patterns, demographics, networks, and trip tables. The agent-based MATSim toolkit allows modelers to track individual travelers and individual vehicles, with great temporal and spatial detail. MATSim’s algorithms help improve individual travel plans (by changing tour and trip start times, destinations, modes, and routes). Here, the SAV mode requests were simulated through a stochastic process for four possible fare levels: $0.50, $0.75, $1, and $1.25 per trip-mile. These fares resulted in mode splits of 50.9, 12.9, 10.5, and 9.2% of the region’s person-trips, respectively. Mode choice results show longer-distance travelers preferring SAVs to private, human-driven vehicles (HVs)—thanks to the reduced burden of SAV travel (since one does not have to drive the vehicle). For travelers whose households do not own an HV, SAVs (rather than transit, walking and biking) appear preferable for trips under 10 miles, which is the majority of those travelers’ trip-making. It may be difficult for traditional transit services and operators to survive once SAVs become available in regions like Austin, where dedicated rail lines and bus lanes are few. Simulation of SAV fleet operations suggest that higher fare rates allow for greater vehicle replacement (ranging from 5.6 to 7.7 HVs per SAV, assuming that the average SAV serves 17–20 person-trips per day); when fares rise, travel demands shift away from longer trip distances. Empty vehicle miles traveled by the fleet of SAVs ranged from 7.8 to 14.2%, across the scenarios in this study. Implications of mobility and sustainability benefits of SAVs are also discussed in the paper.     

Within-day recharge of plug-in hybrid electric vehicles: Energy impact of public charging infrastructure

This paper examines the role of public charging infrastructure in increasing the share of driving on electricity that plug-in hybrid electric vehicles might exhibit, thus reducing their gasoline consumption. Vehicle activity data obtained from a global positioning system tracked household travel survey in Austin, Texas, is used to estimate gasoline and electricity consumptions of plug-in hybrid electric vehicles. Drivers’ within-day recharging behavior, constrained by travel activities and public charger availability, is modeled. It is found that public charging offers greater fuel savings for hybrid electric vehicles s equipped with smaller batteries, by encouraging within-day recharge, and providing an extensive public charging service is expected to reduce plug-in hybrid electric vehicles gasoline consumption by more than 30% and energy cost by 10%, compared to the scenario of home charging only.     

A real-time adaptive signal control in a connected vehicle environment

The state of the practice traffic signal control strategies mainly rely on infrastructure based vehicle detector data as the input for the control logic. The infrastructure based detectors are generally point detectors which cannot directly provide measurement of vehicle location and speed. With the advances in wireless communication technology, vehicles are able to communicate with each other and with the infrastructure in the emerging connected vehicle system. Data collected from connected vehicles provides a much more complete picture of the traffic states near an intersection and can be utilized for signal control. This paper presents a real-time adaptive signal phase allocation algorithm using connected vehicle data. The proposed algorithm optimizes the phase sequence and duration by solving a two-level optimization problem. Two objective functions are considered: minimization of total vehicle delay and minimization of queue length. Due to the low penetration rate of the connected vehicles, an algorithm that estimates the states of unequipped vehicle based on connected vehicle data is developed to construct a complete arrival table for the phase allocation algorithm. A real-world intersection is modeled in VISSIM to validate the algorithms. Results with a variety of connected vehicle market penetration rates and demand levels are compared to well-tuned fully actuated control. In general, the proposed control algorithm outperforms actuated control by reducing total delay by as much as 16.33% in a high penetration rate case and similar delay in a low penetration rate case. Different objective functions result in different behaviors of signal timing. The minimization of total vehicle delay usually generates lower total vehicle delay, while minimization of queue length serves all phases in a more balanced way.     

The optimization of lane assignment and signal timing at the tandem intersection with pre‐signal

This paper presents an integrated model for optimizing lane assignment and signal timing at tandem intersection, which is introduced recently. The pre‐signal is utilized in the tandem intersection to reorganize the traffic flow; hence, the vehicles, regardless of whether left‐turns or through vehicles, can be discharged in all the lanes. However, the previous work does not consider the extra traffic disruption and the associated delay caused by the additional pre‐signal. In the paper, the extra delay aroused by the coordination is incorporated in a lane assignment and signal timing optimization model, and the problem is converted into a mixed‐integer non‐linear programming. A feasible directions method is hence introduced to solve the mixed‐integer non‐linear programming. The result of the optimization shows that the performance of the tandem intersection is improved and the average delay is minimized. The comparison between the tandem and the conventional configuration is presented, and the results verify that the former shows better performance than the latter. In addition, the optimal sequence corresponding to the turning proportion and the optimal lane assignment at the upstream approach of the pre‐signal are presented. Furthermore, if the number of lanes is equal in all arms, the paper proves that the average delay will be reduced if lane assignment is proportional to the turning proportion and the vehicles with low proportion are discharged in advance. Copyright © 2013 John Wiley & Sons, Ltd.     

The evaluation of active bus-priority signal routes

In an attempt to provide priority facilities for high occupancy vehicles, many cities have investigated or installed active bus priority signals at selected intersections. This paper describes one such installation at the intersection of Bell Street and Oriel Road in Heidelberg, Victoria, Australia. In particular, it describes the impact of the signals on bus performance levels and on non-priority traffic performance levels. An evaluation is performed taking account of the costs of the installation, the changes in the amount of fuel consumed and the changes in the perceived, budgeted delay of people passing through the intersection. Perceived, budgeted delay is defined so as to take account of the variability of delay and the perception of small delay changes. The evaluation at this site showed that, for various reasons, it was difficult to justify the priority signals at this isolated intersection.The evaluation is then extended to the concept of a route of bus priority signal intersections. A simple model is built to simulate the performance of such a priority route and the evaluation repeated. As a result of using perceived delay as a measure of performance, it is then shown that although the priority intersections along the route may not be individually justifiable, the priority route as a whole may show considerable net benefits. These benefits will occur given that there are greater than a critical number of priority intersections on the route. This critical number will depend on the assumptions made in the priority route model.It is concluded that re-evaluation of bus priority signal intersections along the lines suggested in the paper may yield a number of viable bus priority intersections and bus priority routes which were previously considered to be non-viable.     

The evening commute with cars and transit: Duality results and user equilibrium for the combined morning and evening peaks

This paper extends Vickrey’s (1969) commute problem for commuters wishing to pass a bottleneck for both cars and transit that share finite road capacity. In addition to this more general framework considering two modes, the paper focuses on the evening rush, when commuters travel from work to home. Commuters choose which mode to use and when to travel in order to minimize the generalized cost of their own trips, including queueing delay and penalties for deviation from a preferred schedule of arrival and departure to and from work. The user equilibrium for the isolated morning and evening commutes are shown to be asymmetric because the schedule penalty in the morning is the difference between the departure and wished curves, and the schedule penalty in the evening is the difference between the arrival and wished curves. It is shown that the system optimum in the morning and evening peaks are symmetric because queueing delay is eliminated and the optimal arrival curves are the same as the departure curves.The paper then considers both the morning and evening peaks together for a single mode bottleneck (all cars) with identical travelers that share the same wished times. For a schedule penalty function of the morning departure and evening arrival times that is positive definite and has certain properties, a user equilibrium is shown to exist in which commuters travel in the same order in both peaks. The result is used to illustrate the user equilibrium for two cases: (i) commuters have decoupled schedule preferences in the morning and evening and (ii) commuters must work a fixed shift length but have flexibility when to start. Finally, a special case is considered with cars and transit: commuters have the same wished order in the morning and evening peaks. Commuters must use the same mode in both directions, and the complete user equilibrium solution reveals the number of commuters using cars and transit and the period in the middle of each rush when transit is used.