Flamelet combustion model for stratified EGR distribution in a diesel engine

Numerous research has been devoted to finding a method to simultaneously reduce NOx and soot emissions from diesel engines. In-cylinder EGR stratification is a technique that simultaneously reduces NOx and soot using a nonuniform EGR distribution in the combustion chamber. To study the potential of in-cylinder EGR stratification, a new combustion model is required that considers the non-uniform EGR distribution and the chemical kinetics. In this study, a new combustion model, the Flamelet for Stratified EGR (FSE) model, was developed to consider the non-uniform in-cylinder gas distribution based on chemical kinetics. The concept of the FSE model is based on using multiple flamelets with the multizone concept. To describe the non-uniform gas distribution, the combustion chamber is divided into several zones by oxygen concentration at the start of injection. Then, the flamelet equations are solved at the boundary of each zone. The final species mass fraction of each cell is calculated using linear interpolation between two results from the boundaries. In this paper, the FSE model was validated under in-cylinder EGR stratification conditions, and then, the potential of in-cylinder EGR stratification was studied by using the FSE model. The effect of in-cylinder EGR stratification was verified under various injection timing, engine speed, and road conditions with optimized engine geometries. The results shows simultaneous NOx and soot reductions under the stratified EGR condition.     

Study of strategy for model-based cooperative control of EGR and VGT in a diesel engine

There is a mutual influence between the effects of controlling exhaust gas recirculation (EGR) and a variable geometry turbocharger (VGT). This paper presents an approach through the application of a control system CAD program and rapid prototyping tools to improve transient operating states by referring to a model-based exhaust recirculation and variable geometry turbocharger control algorithm. The operation model for estimating the state conditions of EGR and a VGT was built on the controller. Simulation and experimental results demonstrating the effectiveness of optimized transient control are also described.     

Pressure model based coordinated control of VGT and dual-loop EGR in a diesel engine air-path system

This paper describes a pressure-model-based coordinated control method of a variable geometry turbine (VGT) and dual-loop exhaust gas recirculation (EGR) in a diesel engine air-path system. Conventionally, air fraction or burnt gas fraction states are controlled for the control of dual-loop EGR systems, but fraction control is not practical since sensors for fractions are not available on production engines. In fact, there is still great controversy over how best to select control outputs for dual-loop EGR systems. In this paper, pressure and mass flow states are chosen as control outputs without fraction states considering the availability and reliability of sensors. A coordinated controller based on the simple control-oriented model is designed with practical aspects, which is applicable for simultaneous operations of high pressure (HP) EGR, low pressure (LP) EGR, and VGT. In addition, the controller adopts the method of input-output linearization using back-stepping to solve the chronic problems of conventional pressure-based controllers such as coupling effects between operations of HP EGR, and VGT. The control performance is verified by simulation based on the proven GT-POWER model of a heavy-duty 6000cc diesel engine air-path.     

Investigation on the flow and heat transfer characteristics of diesel engine EGR coolers

An important goal in diesel engine research is the development of a means to reduce the emissions of nitrogen oxides (NOx). The use of a cooled exhaust gas recirculation (EGR) system is one of the most effective techniques currently available for reducing nitrogen oxides. Since PM (Particulate Matter) fouling reduces the efficiency of an EGR cooler, a tradeoff exists between the amount of NOx and PM emissions, especially at high engine loads. In the present study, we performed engine dynamometer experiments and numerical analyses to investigate how the internal shape of an EGR cooler affects the heat exchanger efficiency. Heat exchanger efficiencies were examined for plain and spiral EGR coolers. The temperature and pressure distributions inside these EGR coolers were obtained in three dimensions using the numerical package program FLUENT.     

Numerical study of a light-duty diesel engine with a dual-loop EGR system under frequent engine operating conditions using the doe method

Exhaust gas recirculation (EGR) is an emission control technology that allows for a significant reduction in NOx emissions from light- and heavy-duty diesel engines. The primary effects of EGR are a lower flame temperature and a lower oxygen concentration of the working fluid in the combustion chamber. A high pressure loop (HPL) EGR is characterized by a fast response, especially at lower speeds, but is only applicable if the turbine upstream pressure is sufficiently higher than the boost pressure. On the contrary, for the low pressure loop (LPL) EGR, a positive differential pressure between the turbine outlet and the compressor inlet is generally available. However, a LPL EGR is characterized by a slow response, especially at low and moderate speeds. In this study, of the future types of EGR systems, the dual-loop EGR system (which has the combined features of the high-pressure loop EGR and the low-pressure loop EGR) was developed and was optimized under five selected operating conditions using a commercial engine simulation program (GT-POWER) and the DOE method. Finally, significant improvements in the engine exhaust emissions and performance were obtained by controlling several major variables.     

Effects of split injection,oxygen enriched air and heavy EGR on soot emissions in a diesel engine

The effects of split injection, oxygen enriched air, and heavy exhaust gas recirculation (EGR) on soot emissions in a direct injection diesel engine were studied using the KIVA-3V code. When split injection is applied, the second injection of fuel into a cylinder results in two separate stoichiometric zones, which helps soot oxidation. As a result, soot emissions are decreased. When oxygen enriched air is applied together with split injection, a higher concentration of oxygen causes higher temperatures in the cylinder. The increase in temperature promotes the growth reaction of acetylene with soot. However, it does not improve acetylene formation during the second injection of fuel. As more acetylene is consumed in the growth reaction with soot, the concentration of acetylene in the cylinder is decreased, which leads to a decrease in soot formation and thus soot emissions. A combination of split injection, a high concentration of oxygen, and a high EGR ratio shows the best results in terms of diesel emissions. In this paper, the split injection scheme of 75.8.25, in which 75% of total fuel is injected in the first pulse, followed by 8°CA of dwell time, and 25% of fuel is injected in the second pulse, with an oxygen concentration of 23% in volume and an EGR ratio of 30% shows a 45% reduction in soot emissions, with the same NOx emissions as in single injection.     

Combustion and emission characteristics of BD20 reformed by ultrasonic energy for different injection delay and EGR rate in a diesel engine

The purpose of this study is to understand the operational characteristics of a diesel engine that uses BD20 reformed by ultrasonic energy irradiation. In particular we study the effects of tuning injection delay and EGR rate. BD containing about 10% oxygen has attracted attention due to soaring crude oil prices and environmental pollution. This oxygen decreases soot by promoting combustion, but it also increases NOx. To solve this problem, injection timing may be delayed or an EGR system may be applied. These adjustments normally lower engine power and increase exhaust emission but, in using fuel reformed by ultrasonic energy irradiation (which is changed physically and chemically to promote combustion), we may hope to circumvent this problem. To control the duration of the ultrasonic energy irradiation, the capacity of the chamber in an ultrasonic energy fuel supply system was tested at 550cc and 1100cc capacities. As for the results of the experiment, we could identify the optimum EGR rate by investigating the engine performance and the characteristics of exhaust emissions according to the injection timing and the EGR rate while ultrasonically irradiated BD20 was fed to a commercial diesel engine. With UBD20 (at an injection timing of BTDC 16°), the optimum EGR rate, giving satisfactory engine performance and exhaust emissions characteristics, was in the range of 15∼20%.     

Effects of diesel fuel characteristics on spray and combustion in a diesel engine

Fuel properties play a dominant role in the spray, mixture formation and combustion process, and are a key to emission control and efficiency optimization. This paper deals with the influence of the fuel properties on the spray and combustion characteristics in a high-pressure and temperature chamber. Light diesel fuel spray and combustion images were taken by using a high-speed video camera and analyzed by their penetration and evaporation characteristics in comparison with current diesel fuel. Then, a single-cylinder DI engine was used to investigate combustion and exhaust characteristics. The mixture formation of the light diesel fuel is faster than that of the current fuel depending on physical properties like boiling point, density, viscosity and surface tension. Engine test results show that smoke is reduced without an increase in other emissions.     

Model based burnt gas fraction controller design of diesel engine with VGT/Dual loop EGR system

-Recently, regulation of NOx and PM emission in diesel engines has become stricter and the EGR system has been expanded into a dual loop EGR system to increase EGR rate as well as to utilize exhaust gas strategically. In terms of engine combustion characteristics, burnt gas fraction is becoming an important factor of solving the NOx and PM emission reduction problem more efficiently but conventional controller focused only pressure and air flow rate targets. Unlike the previous studies, this paper describes a model based burnt gas fraction control structure for a diesel engine with a dual loop EGR and a turbocharger. Feedforward control inputs based on burnt gas fraction states aids in the precise control of diesel engines, especially in transient states by considering coupled behavior within the system. For the controller validation, a control oriented reduced order model of a diesel engine air management system is established to simplify the control input computation and its stability is proved by analysing the internal dynamics stability. Then, a sliding mode controller is designed and controller robustness at certain operating points is validated using an HiLS bench.     

柴油一天然气双燃料发动机介绍

本文通过对双燃料系统进行原理、系统优缺点介绍,经济性进行分析,认为双燃料发动机比柴油发动机有更大的推广潜力,使人们对双燃料重卡相对于柴油重卡有有比较深刻的认识。     

国内柴油机企业的竞争与变局--2005年柴油机市场分析

12005年商用车市场走势特征及影响因素分析据中国汽车工业协会最新统计,从柴油化率来看,2005年我国重卡为99%、中卡98%、轻卡89%;大客91%、中客97%、轻客35%。因此可以说,商用车,尤其是中、重卡(相对于中、重卡来讲,大、中型客车的市场份额很小)的市场走向决定了柴油机的市场走     

柴油机的预防维修与检查

成都公交从1995年开始大量使用柴油机,先后装车的有杭发6120、朝柴6102、上柴D6114A、上柴D6114B、玉柴和大柴柴油机,至现在使用了上柴T6114ZLQ4B。多年以来对柴油机的维修除了定期保养外,对故障均是采取了视情修理,即用坏了再卸下维修。这种局面不仅造成维修费用的浪费,也耽误了营运车辆的正常生产。经过多年的实践,我认为完全可以对柴油机进行预防性检查与维修。     

Efficiency and ecological characteristics of a VCR diesel engine

Compression ratio (CR) is a design parameter with highest influence on efficiency, emission and engine characteristics. In conventional internal combustion (IC) engines, the compression ratio is fixed and their performance is, therefore, a compromise between conflicting requirements. One fundamental problem is that drive units in the vehicles must successfully operate at variable speed and loads and in different ambient conditions. If a diesel engine has a fixed CR, a minimal value must be chosen that can achieve a reliable self-ignition when starting the engine in cold start conditions. In diesel engines, variable compression ratio (VCR) provides control of peak cylinder pressure, improves cold start ability and low load operation, enabling the multi-fuel capability, increase of fuel economy and reduction of emissions. By application of VCR and other mechanisms, the optimal regime fields are extended to the prime requirements: consumption, power, emission, noise, etc., and/or the possibility of the engine to operate with different fuels is extended. An experimental Diesel engine has been developed at the Faculty of Engineering, University of Kragujevac. The changes of CR are realized by changing the piston chamber diameter. Detailed engine tests were performed at the Laboratory for IC engines. Special attention has been given to decrease of fuel consumption and exhaust emissions. An optimal field of CR variation has been determined depending on the given objectives: minimal fuel consumption, minimal nitric oxides, and particulate matter emissions, etc.     

增压柴油机排气再循环（EGR）控制系统的设计

因为某柴油机NOx排放超过国Ⅲ标准,根据据发动机EGR控制系统的要求和特点,为了控制氮氧化物的排放,设计了EGR控制系统的硬件以及控制软件,通过发动机排放13工况试验,结果表明效果良好。     

Operating strategy for gasoline/diesel dual-fuel premixed compression ignition in a light-duty diesel engine

Environmental problems have become a major issue for diesel engine development. Although emission aftertreatment systems such as DPFs (diesel particulate filters), LNTs (lean NOx traps) and SCR (selective catalytic reduction) have been used in diesel vehicles, the manufacturing cost increase caused by this equipment can be hard to be control. Thus, it is better for engine emissions to be reduced by improving the combustion system. A dual-fuel combustion concept is a recommended method to improve a combustion system and effectively reduce emissions. Low reactivity fuel including gasoline and natural gas, which was supplied to the intake port by the FPI (port fuel injector), improved the premixed air-fuel mixture conditions before ignition. Additionally, a small amount of high reactivity fuel, in this case diesel, was injected into the cylinder directly as an ignition source. This dual-fuel combustion promises lower levels of NOx (nitrogen oxide) and PM (particulate matter) emissions due to the elimination of local rich regions in the cylinder. However, it is challenging to control the dual-fuel combustion because the combustion stability and efficiency deteriorate due to the lack of ignition source and reactivity. Thus, it is important to establish an appropriate dual-fuel operating strategy to achieve stable, high efficiency and low emission operation. As a result of this research, a detailed operating method of dual-fuel PCI (premixed compression ignition) was introduced in detail at a low speed and low load condition by using a single cylinder diesel engine. Engine operating parameters including the gasoline ratio, a diesel injection strategy consisting of multiple injectors and timing, the EGR (exhaust gas recirculation) rate and the intake pressure were controlled to satisfy the low ISNOx (indicated specific NOx) and PM emissions levels (0.21 g/kWh and 0.1 FSN, 0.040 g/kWh, respectively) as per the EURO-6 regulation without any after-treatment systems. The results emphasized that a well-constructed dual-fuel PCI operating strategy showed low NOx and PM emissions and high GIE (gross indicated fuel conversion efficiency) with excellent combustion stability.     

Influence of pilot injection on combustion characteristics and emissions in a DI diesel engine fueled with diesel and DME

This work experimentally investigates how the dwell time between pilot injection and main injection influences combustion and emissions characteristics (NOx, CO, THC and smoke) in a single-cylinder DI diesel engine. The experiments were conducted using two fuel injection systems according to the fuel type, diesel or dimethyl ether (DME), due to the different fuel characteristics. The injection strategy is accomplished by varying the dwell time (10°CA, 16°CA and 22°CA) between injections at five main injection timings (?4°CA aTDC, ?2°CA aTDC, 0°CA aTDC, 2°CA aTDC and 4°CA aTDC). Results from pilot-main injection conditions are compared with those shown in single injection conditions to better demonstrate the potential of pilot injection. It was found that pilot injection is highly effective for lowering heat-release rates with smooth pressure traces regardless of the fuel type. Pilot injection also offers high potential to maintain or increase the BMEP; even the combustion-timing is retarded to suppress the NOx emission formation. Overall, NOx emission formation was suppressed more by the combustion phasing retard effect, and not the pilot injection effect considered in this study. Comparison of the emissions for different fuel types shows that CO and HC emissions have low values below 100 ppm for DME operation in both single injection and pilot-main injection. However, NOx emission is slightly higher in the earlier main injection timings (?4°CA aTDC, ?2°CA aTDC) than diesel injections. Pilot injection was found to be more effective with DME for reducing the amount of NOx emission with combustion retardation, which indicates a level of NOx emission similar to that of diesel. Although the diesel pilot-main injection conditions show higher smoke emission than single-injection condition, DME has little smoke emission regardless of injection strategy.     

Model-based optimization of parameters for a diesel engine SCR system

A Selective Catalytic Reduction (SCR) system simulation model for diesel engines was established based on MATLAB/Simulink. The model includes four subsystems: signal acquisition, DEF (Diesel Exhaust Fluid) dosing control, catalytic chemistry reaction and NO_X emissions reduction. The SCR control strategy was optimized based on ETC simulation results. Simulation and test results indicate that the model developed in this paper can predict ETC NO_X emissions accurately.     

柴油机掺烧液化石油气装置的开发与研究

面对污染日益严重的城市环境,本文提出了将柴油公交车改装成为柴油掺烧液化石油气的方案.该方案对于资金短缺,石油气资源相对丰富的城市而言,不失为一种极为切实可行的选择.文中对该方案的核心装置--柴油掺烧液化石油气装置的工作原理、可行性实验、技术指标、和成本核算等项内容进行了深入得分析.