双曲壳的非线性动力分析

本文用实时动力松弛法分析了具有材料和几何非线性的双曲壳的动力响应。采用Mises屈服准则和结合应变强化规律的Prandtl-Reuss流动理论,导得适宜的弹塑性本构关系。在介绍求解运动方程方法时,特别论述了估算时间步长的问题。对不同网格尺寸和沿厚度弹塑性层数对结果精度的影响也作了讨论。并以受突加均匀外压的浅球盖壳为例进行了分析,其结果与文献中的解相当吻合。     

液舱晃荡与浮体非线性耦合运动分析(英文)

Nonlinear interactions among incident wave, tank-sloshing and floating body coupling motion are investigated. The fully nonlinear sloshing and body-surface nonlinear free surface hydrodynamics is simulated using a Non-Uniform Rational B-Spline (NURBS) higher-order panel method in time domain based on the potential theory. A robust and stable improved iterative procedure (Yan and Ma, 2007) for floating bodies is used for calculating the time derivative of velocity potential and floating body motion. An energy dissipation condition based on linear theory adopted by Huang (2011) is developed to consider flow viscosity effects of sloshing flow in nonlinear model. A two-dimensional tank model test was performed to identify its validity. The present nonlinear coupling sway motion results are subsequently compared with the corresponding Rognebakke and Faltinsen (2003)’s experimental results, showing fair agreement. Thus, the numerical approach presented in this paper is expected to be very efficient and realistic in evaluating the coupling effects of nonlinear sloshing and body motion.     

水动力效率最高的鳗鱼推进器(英文)

It is hypothesized that steady anguilliform swimming motion of aquatic animals is purely reactive such that no net vortex wake is left downstream. This is versus carangiform and tunniform swimming of fish, where vortex streams are shed from tail, fins, and body. But there the animal movements are such to produce partial vortex cancellation downstream in maximizing propulsive efficiency. In anguilliform swimming characteristic of the eel family, it is argued that the swimming motions are configured by the animal such that vortex shedding does not occur at all. However, the propulsive thrust in this case is higher order in the motion amplitude, so that relatively large coils are needed to produce relatively small thrust; the speeds of anguilliform swimmers are less than the carangiform and tunniform, which develop first order thrusts via lifting processes. Results of experimentation on live lamprey are compared to theoretical prediction which assumes the no-wake hypothesis. Two-dimensional analysis is first performed to set the concept. This is followed by three-dimensional analysis using slender-body theory. Slender-body theory has been applied by others in studying anguilliform swimming, as it is ideally suited to the geometry of the lamprey and other eel-like animals. The agreement between this new approach based on the hypothesis of wakeless swimming and the experiments is remarkably good in spite of the physical complexities.     

系泊系统非线性恢复力研究及其应用(英文)

Mooring system plays an important role in station keeping of floating offshore structures.Coupled analysis on mooring-buoy interactions has been increasingly studied in recent years.At present,chains and wire ropes are widely used in offshore engineering practice.On the basis of mooring line statics,an explicit formulation of single mooring chain/wire rope stiffness coefficients and mooring stiffness matrix of the mooring system were derived in this article,taking into account the horizontal restoring force,vertical restoring force and their coupling terms.The nonlinearity of mooring stiffness was analyzed,and the influences of various parameters,such as material,displacement,pre-tension and water depth,were investigated.Finally some application cases of the mooring stiffness in hydrodynamic calculation were presented.Data shows that this kind of stiffness can reckon in linear and nonlinear forces of mooring system.Also,the stiffness can be used in hydrodynamic analysis to get the eigenfrequency of slow drift motions.     

耦合非线性三维海洋立管的边界控制(英文)

This paper presents a design of boundary controllers implemented at the top end for global stabilization of a marine riser in a three dimensional space under environmental loadings. Based on the energy approach, nonlinear partial differential equations of motion, including bending-bending and longitudinal-bending couplings for the risers are derived. The couplings cause mutual effects between the three independent directions in the riser’s motions, and make it difficult to minimize its vibrations. The Lyapunov direct method is employed to design the boundary controller. It is shown that the proposed boundary controllers can effectively reduce the riser’s vibration. Stability analysis of the closed-loop system is performed using the Lyapunov direct method. Numerical simulations illustrate the results.     

Green-Naghdi理论的全非线性浅水波数值模拟(英文)

Green-Naghdi (G-N) theory is a fully nonlinear theory for water waves. Some researchers call it a fully nonlinear Boussinesq model. Different degrees of complexity of G-N theory are distinguished by “levels” where the higher the level, the more complicated and presumably more accurate the theory is. In the research presented here a comparison was made between two different levels of G-N theory, specifically level II and level III G-N restricted theories. A linear analytical solution for level III G-N restricted theory was given. Waves on a planar beach and shoaling waves were both simulated with these two G-N theories. It was shown for the first time that level III G-N restricted theory can also be used to predict fluid velocity in shallow water. A level III G-N restricted theory is recommended instead of a level II G-N restricted theory when simulating fully nonlinear shallow water waves.     

波导中带帽圆柱壳的声辐射快速预报(英文)

In order to predict acoustic radiation from a structure in waveguide, a method based on wave superposition is proposed, in which the free-space Green's function is used to match the strength of equivalent sources. In addition, in order to neglect the effect of sound reflection from boundaries, necessary treatment is conducted, which makes the method more efficient. Moreover, this method is combined with the sound propagation algorithms to predict the sound radiated from a cylindrical shell in waveguide. Numerical simulations show the effect of how reflections can be neglected if the distance between the structure and the boundary exceeds the maximum linear dimension of the structure. It also shows that the reflection from the bottom of the waveguide can be approximated by plane wave conditionally. The proposed method is more robust and efficient in computation, which can be used to predict the acoustic radiation in waveguide.     

舵几何参数对桨舵系统水动力性能的分析(英文)

In order to study the effects of geometric parameters of the rudder on the hydrodynamic performance of the propeller-rudder system,the surface panel method is used to build the numerical model of the steady interaction between the propeller and rudder to analyze the relevant factors.The interaction between the propeller and rudder is considered through the induced velocities,which are circumferentially averaged,so the unsteady problem is translated to steady state.An iterative calculation method is used until the hydrodynamic performance converges.Firstly,the hydrodynamic performance of the chosen propeller-rudder system is calculated,and the comparison between the calculated results and the experimental data indicates that the calculation program is reliable.Then,the variable parameters of rudder are investigated,and the calculation results show that the propeller-rudder spacing has a negative relationship with the efficiency of the propeller-rudder system,and the rudder span has an optimal match range with the propeller diameter.Futhermore,the rudder chord and thickness both have a positive correlation with the hydrodynamic performance of the propeller-rudder system.     

海上自升式平台动力分析方法研究(英文)

A jack-up platform,with its particular structure,showed obvious dynamic characteristics under complex environmental loads in extreme conditions.In this paper,taking a simplified 3-D finite element dynamic model in extreme storm conditions as research object,a transient dynamic analysis method was proposed,which was under both regular and irregular wave loads.The steps of dynamic analysis under extreme conditions were illustrated with an applied case,and the dynamic amplification factor(DAF) was calculated for each response parameter of base shear,overturning moment and hull sway.Finally,the structural response results of dynamic and static were compared and analyzed.The results indicated that the static strength analysis of the Jack-up Platforms was not enough under the dynamic loads including wave and current,further dynamic response analysis considering both computational efficiency and accuracy was necessary.     

用于海船精确驾驶的控制率动力修正研究(英文)

The objective of this work is the analytical synthesis problem for marine vehicles autopilots design.Despite numerous known methods for a solution,the mentioned problem is very complicated due to the presence of an extensive population of certain dynamical conditions,requirements and restrictions,which must be satisfied by the appropriate choice of a steering control law.The aim of this paper is to simplify the procedure of the synthesis,providing accurate steering with desirable dynamics of the control system.The approach proposed here is based on the usage of a special unified multipurpose control law structure that allows decoupling a synthesis into simpler particular optimization problems.In particular,this structure includes a dynamical corrector to support the desirable features for the vehicle’s motion under the action of sea wave disturbances.As a result,a specialized new method for the corrector design is proposed to provide an accurate steering or a trade-off between accurate steering and economical steering of the ship.This method guaranties a certain flexibility of the control law with respect to an actual environment of the sailing;its corresponding turning can be realized in real time onboard.     

关于“船舶结构中组合旋转壳的应力分析”的讨论(英文)

The authors have made an excellent contribution to the application of thetransfer matrix method in combined shells of revolution. In this connection, Iwould like to make the following suggestions for the future extension of theirwork:     

弹塑性板壳结构非线性有限元分析

本文根据塑性流动理论的基本公式，由隐式积分导出了与路径无关的变量更新算法和一致切线模量。采用单元广义应力应变直接离散塑性流动定律，构造了杂交应力单元一致切线刚度矩阵的显式表达式，编制了结构有限元程序ＳＡＦＥ，并对弹塑性非线性屈曲和极限承载能力进行分析计算，得到了一些有用的结论。     

有限元法在非线性波浪与结构物相互作用中的应用(英文)

We review recent advances in the finite element method (FEM) simulations of interactions between waves and structures. Our focus is on the potential theory with the fully nonlinear or second-order boundary condition. The present paper has six sections. A review of previous work on interactions between waves and ocean structures is presented in Section one. Section two gives the mathematical formulation. In Section three, the finite element discretization, mesh generation and the finite element linear system solution methods are described. Section four presents numerical methods including time marching schemes, computation of velocity, remeshing and smoothing techniques and numerical radiation conditions. The application of the FEM to the wave-structure interactions are presented in Section five followed by the concluding remarks in Section six.     

Sanders中长圆柱壳理论及其在海洋工程中的应用(英文)

The cylindrical shell is one of the main structural parts in ocean engineering structures.These cylinders are mostly of medium length,which means that the radius of the cross section is significantly smaller than the length of the cylindrical shell.From the viewpoint of the shell theory,they belong to the mid-long cylindrical shell category.To solve mechanical problems on this kind of structure,especially a cracked cylindrical shell,analysis based on shell theory is necessary.At present the generally used solving system for the mid-long cylindrical shell is too complicated,difficult to solve,and inapplicable to engineering.This paper introduced the Sanders’ mid-long cylindrical shell theory which reduces the difficulty of the solution process,and will be suitable for solving problems with complicated boundary conditions.On this basis,the engineering applications of this theory were discussed in conjunction with the problem of a mid-long cylindrical shell having a circumferential crack.The solution process is simple,and the closed form solution can usually be found.In practical engineering applications,it gives satisfactory precision.     

板壳结构非线性分析的数值方法

根据连续介质力学和非线性有限元理论，推导了进行板壳结构非线性分析的退化壳元的完全拉格朗日（简称Ｔ．Ｌ．）法列式，建立了材料在大变形、大应变情况的本构关系。数值算例证明了本文方法的正确性和有效性。     

流场中任意厚度阻尼复合圆柱壳的声辐射(英文)

The insertion loss of acoustic radiation of damped cylindrical shell described by 3-D elasticity Navier equations under radial harmonic applied load in fluid is presented. The classical integral transform technique, potential theory and Lamè resolution are used to derive the solutions of Navier equations. The higher precision inversion computation is introduced to solve the linear equations. Comparing with acoustic radiation of one-layer cylindrical shell, the influence of thickness, mass density, dilatational wave loss factor and Young's modulus of damping material and circumferential mode number of the cylindrical shell on the insertion loss is concluded. The theoretical model in the paper can be used to deal with the arbitrary thickness and any frequency of the coated layer in dynamic problem. The conclusions may be of theoretical reference to the application of damping material to noise and vibration control of submarines and underwater pipes.     

静水压力对壳液耦合系统频散特性的影响(英文)

The effect of hydrostatic pressure on the vibration dispersion characteristics of fluid-shell coupled structures was studied.Both fluid-loaded cylindrical shells and fluid-filled cylindrical shells were considered.Numerical analysis was applied to solve the dispersion equations for shells filled with or loaded with fluid at various hydrostatic pressures.The results for external pressure showed that non-dimensional axial wave numbers are nearly independent when the pressure is below the critical level.The in...     

大缆材料对旁靠外输系统的动力响应影响分析(英文)

In order to provide a theoretical guide for choosing the material for the hawsers for the FPSO side-by-side offloading system, which is moored by the yoke system, the 3D potential flow theory and full coupled time-domain analysis are presented to study the dynamic response of the offloading system. The Ming Zhu FPSO offloading system in the field BZ25-1 is simulated here; and four different characteristic fiber ropes are used as the material for the hawsers. To acquire an accurate hawser line tension, the polynomial fitting method is used to calculate the nonlinear stiffness of the hawsers. By comparing the hawser lines' tension and the relative motion between the FPSO and the shuttle tanker, a suitable material for the hawser lines is chosen and discussed in this paper. The results indicate that the nonlinear stiffness characteristic of the fiber rope has a small effect on the relative motion of the vessels, but the hawser lines' tension is greatly influenced by the different characteristics of the fiber ropes. The hawser lines' tension with nonlinear stiffness is in accordance with the one with the upper and lower bound linear stiffness, which proves this method of fitting the fiber ropes' nonlinear stiffness is reasonable and reliable.     

半潜平台动力定位系统模型预测控制器设计(英文)

This paper researches how to apply the advanced control technology of model predictive control(MPC) to the design of the dynamic positioning system(DPS) of a semi-submersible platform.First,a linear low-frequency motion model with three degrees of freedom was established in the context of a semi-submersible platform.Second,a model predictive controller was designed based on a model which took the constraints of the system into account.Third,simulation was carried out to demonstrate the feasibility of the controller.The results show that the model predictive controller has good performance and good at dealing with the constraints of the system.     

一种基于CFD的水动力系数计算新方法(英文)

Applications of computational fluid dynamic (CFD) to the maritime industry continue to grow with the increasing development of computers. Numerical approaches have evolved to a level of accuracy which allows them to be applied for hydrodynamic computations in industry areas. Hydrodynamic tests, especially planar-motion-mechanism (PMM) tests are simulated by CFD software -FLUENT, and all of the corresponding hydrodynamic coefficients are obtained, which satisfy the need of establishing the simulation system to evaluate maneuverability of vehicles during the autonomous underwater vehicle scheme design stage. The established simulation system performed well in tests.