An observed traffic pattern in long freeway queues

A simple exercise in data analysis showed that, in queued traffic, a well-defined relation exists between the flow on a homogeneous freeway segment and the segment’s vehicle accumulation. The exercise consisted of constructing cumulative vehicle arrival curves to measure the flows and densities on multiple segments of a queued freeway. At this particular site, each interchange enveloped by the queue exhibited a higher on-ramp flow than off-ramp flow and as a consequence, motorists encountered a steady improvement in traffic conditions (e.g., reduced densities and increased speeds) as they traveled from the tail of the queue to the bottleneck. This finding has practical implications for freeway traffic planning and management. Perhaps most notably, it suggests that the first-order hydrodynamic theory of traffic is adequate for describing some of the more relevant features of queue evolution. This and other practical issues are discussed in some detail.     

RENAISSANCE – A unified macroscopic model-based approach to real-time freeway network traffic surveillance

The paper presents a unified macroscopic model-based approach to real-time freeway network traffic surveillance as well as a software tool RENAISSANCE that has been recently developed to implement this approach for field applications. RENAISSANCE is designed on the basis of stochastic macroscopic freeway network traffic flow modeling, extended Kalman filtering, and a number of traffic surveillance algorithms. Fed with a limited amount of real-time traffic measurements, RENAISSANCE enables a number of freeway network traffic surveillance tasks, including traffic state estimation and short-term traffic state prediction, travel time estimation and prediction, queue tail/head/length estimation and prediction, and incident alarm. The traffic state estimation and prediction lay the operating foundation of RENAISSANCE since RENAISSANCE bases the other traffic surveillance tasks on its traffic state estimation or prediction results. The paper first introduces the utilized stochastic macroscopic freeway network traffic flow model and a real-time traffic measurement model, upon which the complete dynamic system model of RENAISSANCE is established with special attention to the handling of some important model parameters. The algorithms for the various traffic surveillance tasks addressed are described along with the functional architecture of the tool. A simulation test was conducted via application of RENAISSANCE to a hypothetical freeway network example with a sparse detector configuration, and the testing results are presented in some detail. Final conclusions and future work are outlined.     

Some observed details of freeway traffic evolution

Certain details of traffic evolution were studied along a 2 km, homogenous freeway segment located upstream of a bottleneck. By comparing (transformed) cumulative curves constructed from the vehicle counts measured at neighboring loop detectors, it was found that waves propagated through queued traffic like a random walk with predictable statistical variation. There was no observed dependency of wave speed on flow. As such, these waves neither focused nor fanned outward and shocks arose only at the interfaces between free-flowing traffic and the back of queues. Although these traffic features may have long been suspected, actual observations of this kind have hitherto not been documented. Also of note, the shocks separating queued and unqueued traffic sometimes exhibited unexpectedly long transitions between these two states. Finally, some observations presented here corroborate earlier reports that, in unqueued traffic, vehicle velocity is insensitive to flows and that forward-moving changes in traffic states therefore travel with vehicles. Taken together, these findings suggest that certain rather simple models suffice for describing traffic on homogeneous freeway segments; brief discussion of this is offered in Section 5.     

The estimation of a time-dependent OD trip table with vehicle trajectory samples

Abstract

In this paper we discuss a dynamic origin–destination (OD) estimation problem that has been used for identifying time-dependent travel demand on a road network. Even though a dynamic OD table is an indispensable data input for executing a dynamic traffic assignment, it is difficult to construct using the conventional OD construction method such as the four-step model. For this reason, a direct estimation method based on field traffic data such as link traffic counts has been used. However, the method does not account for a logical relationship between a travel demand pattern and socioeconomic attributes. In addition, the OD estimation method cannot guarantee the reliability of estimated results since the OD estimation problem has a property named the ‘underdetermined problem.’ In order to overcome such a problem, the method developed in this paper makes use of vehicle trajectory samples with link traffic counts. The new method is applied to numerical examples and shows promising capability for identifying a temporal and spatial travel demand pattern.     

Estimating median velocity instead of mean velocity at single loop detectors

Loop detectors are the preeminent vehicle detector for freeway traffic surveillance. Although single loops have been used for decades, debate continues on how to interpret the measurements. Many researchers have sought better estimates of velocity from single loops. The preceding work has emphasized techniques that use many samples of aggregate flow and occupancy to reduce the estimation error. Although rarely noted, these techniques effectively seek to reduce the bias due to long vehicles in measured occupancy. This paper presents a different approach, using a new aggregation methodology to estimate velocity and reduce the impact of long vehicles in the original traffic measurements. In contrast to conventional practice, the new estimate significantly reduces velocity estimation errors when it is not possible to control for a wide range of vehicle lengths.     

Optimization of mainline traffic via an adaptive co-ordinated ramp-metering control model with dynamic OD estimation

Frequently implemented at freeway accesses to streamline traffic, ramp-metering control strategy is often implemented during rush hours in heavily congested areas. This paper presents a novel ramp-metering control model capable of optimizing mainline traffic by providing metering rates for accesses within the control segments. Based on Payne's continuum traffic stream model, a linear dynamic model with a quadratic objective function is constructed for integrated-responsive ramp-metering control. Incorporating on-line origin–destination (OD) estimation of co-ordinated interchanges into the proposed model increases efficiency of the control. In addition, an iterative algorithm is proposed to obtain the optimal solution. Simulation results demonstrate the robustness of the proposed model and its ability to streamline freeway traffic while avoiding traffic congestion.     

User perceptions and engineering definitions of highway level of service: an exploratory statistical comparison

The level of service (LOS) concept in the Highway Capacity Manual has been used as a qualitative measure representing freeway operational conditions for over 35 years. One key element that has not been adequately addressed is how road users perceive LOS. This exploratory research examines road-user perceptions of freeway LOS by presenting study participants with a series of video clips of various traffic conditions (taken from cameras on overpasses to allow a complete view of the traffic stream) and asking them their perceptions of LOS. A random effects ordered probability model is then used to statistically link participant-recorded perceptions of LOS with measurable traffic conditions (speed, density, flow, percentage of trucks, vehicle headways) and participant characteristics. The findings suggest that the Highway Capacity Manual’s use of traffic density as a single performance measure for LOS does not accurately reflect road-user perceptions. The statistical analysis shows that a number of attributes besides traffic density determine public perceptions of LOS and that these perceptions vary depending on both traffic conditions and road-user characteristics.     

Modeling measurement errors and missing initial values in freeway dynamic origin–destination estimation systems

Most existing dynamic origin–destination (O–D) estimation approaches are grounded on the assumption that a reliable initial O–D set is available and traffic volume data from detectors are accurate. However, in most traffic systems, both types of critical information are either not available or subjected to some level of measurement errors such as traffic counts and speed measurement from sensors. To contend with those critical issues, this study presents two robust algorithms, one for estimation of an initial O–D set and the other for tackling the input measurement errors with an extended estimation algorithm. The core concept of the initial O–D estimation algorithm is to decompose the target network in a number of sub-networks based on proposed rules, and then execute the estimation of the initial O–D set iteratively with the observable information at the first time interval. To contend with the inevitable detector measurement error, this study proposes an interval-based estimation algorithm that converts each model input data as an interval with its boundaries being set based on some prior knowledge. The performance of both proposed algorithms has been tested with a simulated system, the I-95 freeway corridor between I-495 and I-695, and the results are quite promising.     

Development of simulated driving cycles for light,medium, and heavy duty trucks: Case of the Toronto Waterfront Area

Driving cycles are an important input for state-of-the-art vehicle emission models. Development of a driving cycle requires second-by-second vehicle speed for a representative set of vehicles. Current standard driving cycles cannot reflect or forecast changes in traffic conditions. This paper introduces a method to develop representative driving cycles using simulated data from a calibrated microscopic traffic simulation model of the Toronto Waterfront Area. The simulation model is calibrated to reflect road counts, link speeds, and accelerations using a multi-objective genetic algorithm. The simulation is validated by comparing simulated vs. observed passenger freeway cycles. The simulation method is applied to develop AM peak hour driving cycles for light, medium and heavy duty trucks. The demonstration reveals differences in speed, acceleration, and driver aggressiveness between driving cycles for different vehicle types. These driving cycles are compared against a range of available driving cycles, showing different traffic conditions and driving behaviors, and suggesting a need for city-specific driving cycles. Emissions from the simulated driving cycles are also compared with EPA’s Heavy Duty Urban Dynamometer Driving Schedule showing higher emission factors for the Toronto Waterfront cycles.     

Vehicle reidentification and travel time measurement on congested freeways

The paper presents an algorithm for matching individual vehicles measured at a freeway detector with the vehicles’ corresponding measurements taken earlier at another detector located upstream. Although this algorithm is potentially compatible with many vehicle detector technologies, the paper illustrates the method using existing dual-loop detectors to measure vehicle lengths. This detector technology has seen widespread deployment for velocity measurement. Since the detectors were not developed to measure vehicle length, these measurements can include significant errors. To overcome this problem, the algorithm exploits drivers’ tendencies to retain their positions within dense platoons. The otherwise complicated task of vehicle reidentification is carried out by matching these platoons rather than individual vehicles. Of course once a vehicle has been matched across neighboring detector stations, the difference in its arrival time at each station defines the vehicle’s travel time on the intervening segment.Findings from an application of the algorithm over a 1/3 mile long segment are presented herein and they indicate that a sufficient number of vehicles can be matched for the purpose of traffic surveillance. As such, the algorithm extracts travel time data without requiring the deployment of new detector technologies. In addition to the immediate impacts on traffic monitoring, the work provides a means to quantify the potential benefits of emerging detector technologies that promise to extract more detailed information from individual vehicles.     

Methods of dropping auxiliary lanes at freeway weaving segments

Auxiliary lanes connecting freeway entrance and exit ramps provide additional space for entering and exiting vehicles to change lanes. The method of dropping auxiliary lanes is critical in the design of freeway auxiliary lanes. This study investigates the performance of different methods of dropping auxiliary lanes. Case studies were conducted at two selected freeway segments with successive entrance or exit ramps in the City of Houston. Traffic simulation analysis results of these two case studies show that additional operational benefits can be achieved by extending an auxiliary lane beyond the freeway weaving segment. The study also found that if the weaving segment is followed by an entrance/exit ramp and this ramp has high traffic volume, it can be less operationally favorable to extend and terminate the auxiliary lane at this entrance/exit ramp location. Instead, dropping the auxiliary lane before this entrance/exit ramp represents a more operationally effective option.     

Exploring the impact of connected and autonomous vehicles on freeway capacity using a revised Intelligent Driver Model

ABSTRACT

Connected and autonomous vehicle (CAV) technologies are expected to change driving/vehicle behavior on freeways. This study investigates the impact of CAVs on freeway capacity using a microsimulation tool. A four-lane basic freeway segment is selected as the case study through the Caltrans Performance Measurement System (PeMS). To obtain valid results, various driving behavior parameters are calibrated to the real traffic conditions for human-driven vehicles. In particular, the calibration is conducted using genetic algorithm. A revised Intelligent Driver Model (IDM) is developed and used as the car-following model for CAVs. The simulation is conducted on the basic freeway segment under different penetration rates of CAVs and different freeway speed limits. The results show that with an increase in the market penetration rate, freeway capacity increases, and will increase significantly as the speed limit increases.     

Stochastic cell transmission model (SCTM): A stochastic dynamic traffic model for traffic state surveillance and assignment

The paper proposes a first-order macroscopic stochastic dynamic traffic model, namely the stochastic cell transmission model (SCTM), to model traffic flow density on freeway segments with stochastic demand and supply. The SCTM consists of five operational modes corresponding to different congestion levels of the freeway segment. Each mode is formulated as a discrete time bilinear stochastic system. A set of probabilistic conditions is proposed to characterize the probability of occurrence of each mode. The overall effect of the five modes is estimated by the joint traffic density which is derived from the theory of finite mixture distribution. The SCTM captures not only the mean and standard deviation (SD) of density of the traffic flow, but also the propagation of SD over time and space. The SCTM is tested with a hypothetical freeway corridor simulation and an empirical study. The simulation results are compared against the means and SDs of traffic densities obtained from the Monte Carlo Simulation (MCS) of the modified cell transmission model (MCTM). An approximately two-miles freeway segment of Interstate 210 West (I-210W) in Los Ageles, Southern California, is chosen for the empirical study. Traffic data is obtained from the Performance Measurement System (PeMS). The stochastic parameters of the SCTM are calibrated against the flow-density empirical data of I-210W. Both the SCTM and the MCS of the MCTM are tested. A discussion of the computational efficiency and the accuracy issues of the two methods is provided based on the empirical results. Both the numerical simulation results and the empirical results confirm that the SCTM is capable of accurately estimating the means and SDs of the freeway densities as compared to the MCS.     

Estimating link travel time functions for heterogeneous traffic flows on freeways

Oversized vehicles, such as trucks, significantly contribute to traffic delays on freeways. Heterogeneous traffic populations, that is, those consisting of multiple vehicles types, can exhibit more complicated travel behaviors in the operating speed and performance, depending on the traffic volume as well as the proportions of vehicle types. In order to estimate the component travel time functions for heterogeneous traffic flows on a freeway, this study develops a microscopic traffic‐simulation based four‐step method. A piecewise continuous function is proposed for each vehicle type and its parameters are estimated using the traffic data generated by a microscopic traffic simulation model. The illustrated experiments based on VISSIM model indicate that (i) in addition to traffic volume, traffic composition has significant influence on the travel time of vehicles and (ii) the respective estimations for travel time of heterogeneous flows could greatly improve their estimation accuracy. Copyright © 2016 John Wiley & Sons, Ltd.     

Examination of factors affecting freeway incident clearance times: a comparison of the generalized F model and several alternative nested models

Traffic incidents are a principal cause of congestion on urban freeways, reducing capacity and creating risks for both involved motorists and incident response personnel. As incident durations increase, the risk of secondary incidents or crashes also becomes problematic. In response to these issues, many road agencies in metropolitan areas have initiated incident management programs aimed at detecting, responding to, and clearing incidents to restore freeways to full capacity as quickly and safely as possible. This study examined those factors that impact the time required by the Michigan Department of Transportation Freeway Courtesy Patrol to clear incidents that occurred on the southeastern Michigan freeway network. These models were developed using traffic flow data, roadway geometry information, and an extensive incident inventory database. A series of parametric hazard duration models were developed, each assuming a different underlying probability distribution for the hazard function. Although each modeling framework provided results that were similar in terms of the direction of factor effects, there was significant variability in terms of the estimated magnitude of these impacts. The generalized F distribution was shown to provide the best fit to the incident clearance time data, and the use of poorer fitting distributions was shown to result in severe over‐estimation or under‐estimation of factor effects. Those factors that were found to impact incident clearance times included the time of day and month when the incident occurred, the geometric and traffic characteristics of the freeway segment, and the characteristics of each incident. Copyright © 2012 John Wiley & Sons, Ltd.     

A fuzzy-logic-based system for freeway bottleneck severity diagnosis in a sensor network

It is essential for local traffic jurisdictions to systematically spot freeway bottlenecks and proactively deploy appropriate congestion mitigation strategies. However, diagnostic results may be influenced by unreliable measurements, analysts’ subjective knowledge and day-to-day traffic pattern variations. In order to suitably address these uncertainties and imprecise data, this study proposes a fuzzy-logic-based approach for bottleneck severity diagnosis in urban sensor networks. A dynamic bottleneck identification model is first proposed to identify bottleneck locations, and a fuzzy inference approach is then proposed to systematically diagnose the severities of the identified recurring and non-recurring bottlenecks by incorporating expert knowledge of local traffic conditions. Sample data over a 1-month period on an urban freeway in Northern Virginia was used as a case study for the analysis. The results reveal that the proposed approach can reasonably determine bottleneck severities and critical links, accounting for both spatial and temporal factors in a sensor network.     

Real-time freeway traffic state estimation based on extended Kalman filter: Adaptive capabilities and real data testing

This paper reports on real data testing of a real-time freeway traffic state estimator, with a particular focus on its adaptive capabilities. The pursued general approach to the real-time adaptive estimation of complete traffic state in freeway stretches or networks is based on stochastic macroscopic traffic flow modeling and extended Kalman filtering. One major innovative feature of the traffic state estimator is the online joint estimation of important model parameters (free speed, critical density, and capacity) and traffic flow variables (flows, mean speeds, and densities), which leads to three significant advantages of the estimator: (1) avoidance of prior model calibration; (2) automatic adaptation to changing external conditions (e.g. weather and lighting conditions, traffic composition, control measures); (3) enabling of incident alarms. These three advantages are demonstrated via suitable real data testing. The achieved testing results are satisfactory and promising for subsequent applications.     

Real-time estimation of turning movement counts at signalized intersections using signal phase information

A variety of sensor technologies, such as loop detectors, traffic cameras, and radar have been developed for real-time traffic monitoring at intersections most of which are limited to providing link traffic information with few being capable of detecting turning movements. Accurate real-time information on turning movement counts at signalized intersections is a critical requirement for applications such as adaptive traffic signal control. Several attempts have been made in the past to develop algorithms for inferring turning movements at intersections from entry and exit counts; however, the estimation quality of these algorithms varies considerably. This paper introduces a method to improve accuracy and robustness of turning movement estimation at signalized intersections. The new algorithm makes use of signal phase status to minimize the underlying estimation ambiguity. A case study was conducted based on turning movement data obtained from a four-leg signalized intersection to evaluate the performance of the proposed method and compare it with two other existing well-known estimation methods. The results show that the algorithm is accurate, robust and fairly straightforward for real world implementation.     

Stochasticity of freeway operational capacity and chance-constrained ramp metering

The notion of capacity is essential to the planning, design, and operations of freeway systems. However, in the practice freeway capacity is commonly referred as a theoretical/design value without consideration of operational characteristics of freeways. This is evident from the Highway Capacity Manual (HCM) 2000 in that no influence from downstream traffic is considered in the definition of freeway capacity. In contrast to this definition, in this paper, we consider the impact of downstream traffic and define freeway operational capacity as the maximum hourly rate at which vehicles can be expected to traverse a point or a uniform section of a roadway under prevailing traffic flow conditions. Therefore freeway operational capacity is not a single value with theoretical notion. Rather, it changes under different traffic flow conditions. Specifically, this concept addresses the capacity loss during congested traffic conditions. We further study the stochasticity of freeway operational capacity by examining loop detector data at three specifically selected detector stations in the Twin Cities’ area. It is found that values of freeway operational capacity under different traffic flow conditions generally fit normal distributions. In recognition of the stochastic nature of freeway capacity, we propose a new chance-constrained ramp metering strategy, in which, constant capacity value is replaced by a probabilistic one that changes dynamically depending on real-time traffic conditions and acceptable probability of risk determined by traffic engineers. We then improve the Minnesota ZONE metering algorithm by applying the stochastic chance constraints and test the improved algorithm through microscopic traffic simulation. The evaluation results demonstrate varying degrees of system improvement depending on the acceptable level of risk defined.     

A phase-based smoothing method for accurate traffic speed estimation with floating car data

In this paper, a novel freeway traffic speed estimation method based on probe data is presented. In contrast to other traffic speed estimators, it only requires velocity data from probes and does not depend on any additional data inputs such as density or flow information. In the first step the method determines the three traffic phases free flow, synchronized flow, and Wide Moving Jam (WMJ) described by Kerner et al. in space and time. Subsequently, reported data is processed with respect to the prevailing traffic phase in order to estimate traffic velocities. This two-step approach allows incorporating empirical features of phase fronts into the estimation procedure. For instance, downstream fronts of WMJs always propagate upstream with approximately constant velocity, and downstream fronts of synchronized flow phases usually stick to bottlenecks. The second step assures the validity of measured velocities is limited to the extent of its assigned phase. Effectively, velocity information in space-time can be estimated more distinctively and the result is therefore more accurate even if the input data density is low.The accuracy of the proposed Phase-Based Smoothing Method (PSM) is evaluated using real floating car data collected during two traffic congestions on the German freeway A99 and compared to the performance of the Generalized Adaptive Smoothing Method (GASM) as well as a naive algorithm. The quantitative and qualitative results show that the PSM reconstructs the congestion pattern more accurately than the other two. A subsequent analysis of the computational efficiency and sensitivity demonstrates its practical suitability.