A method to determine the two-point contact zone and transfer of wheel–rail forces in a turnout

A practical method to determine the zone of two contact points and the transfer of wheel–rail forces between two rails in a turnout is presented in this paper. The method is based on a wheel–rail elastic penetration assumption and used to study a turnout system for a 200 km/h high-speed railway in China. Rail profiles in a number of key sections in the turnout are identified first, and profiles in other sections are then obtained by interpolation between key sections. The track is modelled as flexible with rails and sleepers represented by beams and the interaction between the vehicle and turnout is simulated for cases of the vehicle passing the turnout. Results are mainly presented for two-point contact positions and the characteristics of the wheel–rail forces transference. It is found that the heights of the switch and crossing rail top have significant effects on the wheel–rail contact forces. Finally, the optimised top height for the crossing rails is proposed to reduce the system dynamic force in the turnout system.     

Design optimisation of switch rails in railway turnouts

Inspired by a manufacturing process of switch rails for railway turnouts, a method for the optimisation of switch rail profile geometry is presented. The switch rail profile geometry is parameterised with four design variables to define a B-spline curve for the milling tool profile, and two design variables to prescribe the deviation from the nominal vertical path of the milling tool. The optimisation problem is formulated as a multi-objective minimisation problem with objective functions based on the contact pressure and the energy dissipation in the wheel–rail contact. The front of Pareto optimal solutions is determined by applying a genetic type optimisation algorithm. The switch rail profile designs are evaluated by simulations of dynamic train–turnout interaction. It is concluded that the obtained set of Pareto optimal solutions corresponds to a rather small variation in design variables where increased profile height and increased profile shoulder protuberance are preferred for both objectives. The improvement in the objectives comes at the cost of an earlier wheel transition to the switch rail and thus increased vertical loading at a thinner rail cross-section. The performance of the optimised geometry is evaluated using a set of 120 measured wheel profiles, and it is shown that the optimised geometry reduces damage also for this large load collective. It is concluded that accurate limits on switch rail loading need to be established to determine the feasible design space for switch rail geometry optimisation.     

Study on the derailment behaviour of a railway wheelset with solid axles in a railway turnout

ABSTRACT

Dynamic wheel–rail interaction in railway turnouts is more complicated than on ordinary track. In order to evaluate the derailment behaviour of railway wheelsets in railway turnouts, this paper presents a study of dynamic wheel–rail interaction during a wheel flange climbs on the turnout rails, by applying the elasticity positioning wheelset model. A numerical model is established based on a coupled finite element method and multi-body dynamics, and applied to study the derailment behaviour of a railway wheelset in both the facing and trailing directions in a railway turnout, as well as dynamic wheel–turnout rail interaction during the wheel flange climbing on the turnout rails. The influence of the wheel–rail attack angle and the friction coefficient on the dynamic derailment behaviour is investigated through the proposed model. The results show that the derailment safety for a wheelset passing the railway turnout in facing direction is significantly lower than that for the trailing direction and the ordinary track. The possibility of derailment for the wheelset passing the railway turnout in facing and trailing directions at positive wheel–rail attack angles will increase with an increase in the attack angles, and the possibility of derailment can be reduced by decreasing the friction coefficient.     

重载75kg/m钢轨12号道岔曲尖轨加强设计方案研究

为提高尖轨承载能力,减小轮轨接触应力,增加尖轨薄弱段的耐磨性能,延长道岔使用寿命,对曲尖轨截面在横向荷载下的接触应力进行了研究;通过建立基本轨和曲尖轨的实体模型,应用有限元法,对曲尖轨各截面应力、曲尖轨均匀加宽后各截面应力以及曲尖轨缩短后各截面应力进行了分析。结果表明,尖轨截面应力随轨顶宽度的增加呈现非线性减小趋势,均匀加宽曲尖轨和缩短曲尖轨有利于尖轨的受力。结合对曲尖轨截面应力的研究,提出了尖轨加强的方案。     

Study on lateral dynamic characteristics of vehicle/turnout system

Based on Chinese No. 12 high speed, single-way swing nose rail concrete sleeper turnout, a comprehensive vehicle/turnout system coupling dynamic model has been established in this paper, and the lateral and vertical dynamic characteristics of vehicle/turnout systems have been simulated while the car passes through the turnout zone on divergence. These dynamic characteristics show that the lateral impact and vibration of the systems caused by the wheel/rail contact and irregularity are very intensive, especially at the switch zone and nose area of the turnout, and the lateral dynamics of the turnout system, such as lateral stability, vibrating responses, impacting and the allowable passing velocity force between the wheelsets and the switch rails are much more complicated than that of the vertical ones.     

Study on lateral dynamic characteristics of vehicle/turnout system

Based on Chinese No. 12 high speed, single-way swing nose rail concrete sleeper turnout, a comprehensive vehicle/turnout system coupling dynamic model has been established in this paper, and the lateral and vertical dynamic characteristics of vehicle/turnout systems have been simulated while the car passes through the turnout zone on divergence. These dynamic characteristics show that the lateral impact and vibration of the systems caused by the wheel/rail contact and irregularity are very intensive, especially at the switch zone and nose area of the turnout, and the lateral dynamics of the turnout system, such as lateral stability, vibrating responses, impacting and the allowable passing velocity force between the wheelsets and the switch rails are much more complicated than that of the vertical ones.     

Stochastic analysis of dynamic interaction between train and railway turnout

The performance of a railway turnout (switch and crossing) is influenced by a large number of input parameters of the complex train–turnout system. To reach a robust design that performs well for different traffic situations, random distributions (scatter) of these inputs need to be accounted for in the design process. Stochastic analysis methods are integrated with a simulation model of the dynamic interaction between train and turnout. For a given nominal layout of the turnout, using design of experiments methodology and a two-level fractional factorial screening design, four parameters (axle load, wheel–rail friction coefficient, and wheel and rail profiles) are identified to be the most significant. These parameters are further investigated using a three-level full factorial design and stochastic analysis. The random distributions of transverse wheel profile and set of transverse rail profiles along the switch panel are accounted for by the Karhunen–Loève expansion technique. The influence of the random distributions of the input parameters on the statistical outputs of wheel–rail contact forces, wear and rolling contact fatigue is assessed using Latin hypercube sampling to generate a number of stochastic load realizations.     

Dynamic vehicle–track interaction in switches and crossings and the influence of rail pad stiffness – field measurements and validation of a simulation model

A model for simulation of dynamic interaction between a railway vehicle and a turnout (switch and crossing, S&C) is validated versus field measurements. In particular, the implementation and accuracy of viscously damped track models with different complexities are assessed. The validation data come from full-scale field measurements of dynamic track stiffness and wheel–rail contact forces in a demonstrator turnout that was installed as part of the INNOTRACK project with funding from the European Union Sixth Framework Programme. Vertical track stiffness at nominal wheel loads, in the frequency range up to 20?Hz, was measured using a rolling stiffness measurement vehicle (RSMV). Vertical and lateral wheel–rail contact forces were measured by an instrumented wheel set mounted in a freight car featuring Y25 bogies. The measurements were performed for traffic in both the through and diverging routes, and in the facing and trailing moves. The full set of test runs was repeated with different types of rail pad to investigate the influence of rail pad stiffness on track stiffness and contact forces. It is concluded that impact loads on the crossing can be reduced by using more resilient rail pads. To allow for vehicle dynamics simulations at low computational cost, the track models are discretised space-variant mass–spring–damper models that are moving with each wheel set of the vehicle model. Acceptable agreement between simulated and measured vertical contact forces at the crossing can be obtained when the standard GENSYS track model is extended with one ballast/subgrade mass under each rail. This model can be tuned to capture the large phase delay in dynamic track stiffness at low frequencies, as measured by the RSMV, while remaining sufficiently resilient at higher frequencies.     

Effect of curved track support failure on vehicle derailment

In order to investigate the effect of curved track support failure on railway vehicle derailment, a coupled vehicle–track dynamic model is put forward. In the model, the vehicle and the structure under rails are, respectively, modelled as a multi-body system, and the rail is modelled with a Timoshenko beam rested on the discrete sleepers. The lateral, vertical, and torsional deformations of the beam are taken into account. The model also considers the effect of the discrete support by sleepers on the coupling dynamics of the vehicle and track. The sleepers are assumed to move backward at a constant speed to simulate the vehicle running along the track at the same speed. In the calculation of the coupled vehicle and track dynamics, the normal forces of the wheels/rails are calculated using the Hertzian contact theory and their creep forces are determined with the nonlinear creep theory by Shen et al [Z.Y. Shen, J.K. Hedrick, and J.A. Elkins, A comparison of alternative creep-force models for rail vehicle dynamic analysis, Proceedings of the 8th IAVSD Symposium, Cambridge, MA, 1984, pp. 591–605]. The motion equations of the vehicle/track are solved by means of an explicit integration method. The failure of the components of the curved track is simulated by changing the track stiffness and damping along the track. The cases where zero to six supports of the curved rails fail are considered. The transient derailment coefficients are calculated. They are, respectively, the ratio of the wheel/rail lateral force to the vertical force and the wheel load reduction. The contact points of the wheels/rails are in detail analysed and used to evaluate the risk of the vehicle derailment. Also, the present work investigates the effect of friction coefficient, axle load and vehicle speed on the derailments under the condition of track failure. The numerical results obtained indicate that the failure of track supports has a great influence on the whole vehicle running safety.     

Numerical analysis of the dynamic interaction between wheel set and turnout crossing using the explicit finite element method

A three-dimensional (3-D) explicit dynamic finite element (FE) model is developed to simulate the impact of the wheel on the crossing nose. The model consists of a wheel set moving over the turnout crossing. Realistic wheel, wing rail and crossing geometries have been used in the model. Using this model the dynamic responses of the system such as the contact forces between the wheel and the crossing, crossing nose displacements and accelerations, stresses in rail material as well as in sleepers and ballast can be obtained. Detailed analysis of the wheel set and crossing interaction using the local contact stress state in the rail is possible as well, which provides a good basis for prediction of the long-term behaviour of the crossing (fatigue analysis). In order to tune and validate the FE model field measurements conducted on several turnouts in the railway network in the Netherlands are used here. The parametric study including variations of the crossing nose geometries performed here demonstrates the capabilities of the developed model. The results of the validation and parametric study are presented and discussed.     

Simulation of dynamic interaction between train and railway turnout

Dynamic train–track interaction is more complex in railway turnouts (switches and crossings) than that in ordinary tangent or curved tracks. Multiple contacts between wheel and rail are common, and severe impact loads with broad frequency contents are induced, when nominal wheel–rail contact conditions are disturbed because of the continuous variation in rail profiles and the discontinuities in the crossing panel. The absence of transition curves at the entry and exit of the turnout, and the cant deficiency, leads to large wheel–rail contact forces and passenger discomfort when the train is switching into the turnout track. Two alternative multibody system (MBS) models of dynamic interaction between train and a standard turnout design are developed. The first model is derived using a commercial MBS software. The second model is based on a multibody dynamics formulation, which may account for the structural flexibility of train and track components (based on finite element models and coordinate reduction methods). The variation in rail profile is accounted for by sampling the cross-section of each rail at several positions along the turnout. Contact between the back of the wheel flange and the check rail, when the wheelset is steered through the crossing, is considered. Good agreement in results from the two models is observed when the track model is taken as rigid.     

A dynamic wheel–rail impact analysis of railway track under wheel flat by finite element analysis

Wheel–rail interaction is one of the most important research topics in railway engineering. It involves track impact response, track vibration and track safety. Track structure failures caused by wheel–rail impact forces can lead to significant economic loss for track owners through damage to rails and to the sleepers beneath. Wheel–rail impact forces occur because of imperfections in the wheels or rails such as wheel flats, irregular wheel profiles, rail corrugations and differences in the heights of rails connected at a welded joint. A wheel flat can cause a large dynamic impact force as well as a forced vibration with a high frequency, which can cause damage to the track structure. In the present work, a three-dimensional finite element (FE) model for the impact analysis induced by the wheel flat is developed by the use of the FE analysis (FEA) software package ANSYS and validated by another validated simulation. The effect of wheel flats on impact forces is thoroughly investigated. It is found that the presence of a wheel flat will significantly increase the dynamic impact force on both rail and sleeper. The impact force will monotonically increase with the size of wheel flats. The relationships between the impact force and the wheel flat size are explored from this FEA and they are important for track engineers to improve their understanding of the design and maintenance of the track system.     

Mathematical modelling of train–turnout interaction

The paper proposes a mathematical model of train–turnout interaction in the mid-frequency range (0–500 Hz). The model accounts for the effects of rail profile variation along the track and of local variation of track flexibility. The proposed approach is able to represent the condition of one wheel being simultaneously in contact with more than one rail, allowing the accurate prediction of the effect of wheels being transferred from one rail to another when passing over the switch toe and the crossing nose. Comprehensive results of train–turnout interaction during the negotiation of the main and the branch lines are presented, including the effect of wear of wheel/rail profiles and presence of track misalignment. In the final part of the paper, comparisons are performed between the results of numerical simulations and line measurements performed on two different turnouts for urban railway lines, showing a good agreement between experimental and numerical results.     

Influence of uneven rail irregularities on the dynamic response of the railway track using a three-dimensional model of the vehicle–track system

A mathematical model of the vehicle–track interaction is developed to investigate the coupled behaviour of vehicle–track system, in the presence of uneven irregularities at left/right rails. The railway vehicle is simplified as a 3D multi-rigid-body model, and the track is treated as the two parallel beams on a layered discrete support system. Besides the car-body, the bogies and the wheel sets, the sleepers are assumed to have roll degree of freedom, in order to simulate the in-plane rotation of the components. The wheel–rail interface is treated using a nonlinear Hertzian contact model, coupling the mathematical equations of the vehicle–track systems. The dynamic interaction of the entire system is numerically studied in time domain, employing Newmark's integration method. The track irregularity spectra of both the left/right rails are taken into account, as the inputs of dynamic excitations. The dynamic responses of the track system induced by such irregularities are obtained, particularly in terms of the vertical (bounce) and roll displacements. The numerical model of the present research is validated using several benchmark models reported in the literature, for both the smooth and unsmooth track conditions. Four sample profiles of the measured rail irregularities are considered as the case studies of excitation sources, examining their influences on the dynamic behaviour of the coupled system. The results of numerical simulations demonstrate that the motion of track system is significantly influenced by the presence of uneven irregularities in left/right rails. Dynamic response of the sleepers in the roll direction becomes more sensitive to the rail irregularities, as the unevenness severity of the parallel profiles (quantitative difference between left and right rail spectra) is increased. The severe geometric deformation of the track in the bounce–pitch–roll directions is mainly related to such profile unevenness (cross-level) in left/right rails.     

Switch Panel wear loading – a parametric study regarding governing train operational factors

The acting forces and resulting material degradation at the running surfaces of wheels and rail are determined by vehicle, track, interface and operational characteristics. To effectively manage the experienced wear, plastic deformation and crack development at wheels and rail, the interaction between vehicle and track demands a system approach both in maintenance and in design. This requires insight into the impact of train operational parameters on rail- and wheel degradation, in particular at switches and crossings due to the complex dynamic behaviour of a railway vehicle at a turnout. A parametric study was carried out by means of vehicle-track simulations within the VAMPIRE® multibody simulation software, performing a sensitivity analysis regarding operational factors and their impact on expected switch panel wear loading. Additionally, theoretical concepts were cross-checked with operational practices by means of a case study in response to a dramatic change in lateral rail wear development at specific switches in Dutch track. Data from train operation, track maintenance and track inspection were analysed, providing further insight into the operational dependencies. From the simulations performed in this study, it was found that switch rail lateral wear loading at the diverging route of a 1:9 type turnout is significantly influenced by the level of wheel–rail friction and to a lesser extent by the direction of travel (facing or trailing). The influence of other investigated parameters, being vehicle speed, traction, gauge widening and track layout is found to be small. Findings from the case study further confirm the simulation outcome. This research clearly demonstrates the contribution flange lubrication can have in preventing abnormal lateral wear at locations where the wheel–rail interface is heavily loaded.     

Coupling Model of Vertical and Lateral Vehicle/Track Interactions

A new dynamic model of vehicle/track interaction is presented. The model considers the vehicle and the track as a whole system and couples the vertical interaction with the lateral interaction. The vehicle subsystem is modeled as a multi-body system with 37 degrees of freedom, which runs on the track with a constant velocity. The track substructure is modeled as a discretely supported system of elastic beams representing the rails, sleepers and ballasts. The normal contact forces between wheels and rails are described by Hertzian nonlinear elastic contact theory and the tangential wheel/ rail forces are decided by the creep theory. Numerical results are compared with those of conventional dynamic models of railway vehicles. Applications of the coupling model to the investigation of safety limits against derailment due to the track twist and the combined alignment and cross-level irregularities are reported at the end of the paper.     

Inverse identification of wheel–rail contact forces based on observation of wheel disc strains: an evaluation of three numerical algorithms

In this paper, three numerical algorithms for the identification of wheel–rail contact forces based on measured wheel disc strains on an instrumented railway wheelset are discussed and compared. The three algorithms include one approach resting on static calibration, one that is applying a Kalman filter and the third is exploiting an inverse identification scheme. To demonstrate and evaluate the alternative methods, two load cases including periodic excitation by sinusoidal wheel–rail irregularities and transient excitation by an insulated rail joint are considered. Based on a previously presented vehicle–track interaction model in the time domain, load scenarios are defined by taking the calculated vertical wheel–rail contact forces as the reference force to be re-identified by the proposed algorithms. The reference contact forces are applied on a finite element model of the wheel to generate synthetic observation data, that is, radial strains at the positions of the strain gauges, serving as input to the identification procedures. It is concluded that the inverse identification scheme leads to superior accuracy at higher computational cost. If on-line implementation and evaluation is required, the Kalman filter generates better accuracy than the static calibration approach.     

The impact of structural flexibilities of wheelsets and rails on the hunting behaviour of a railway vehicle

The hunting motion of a passenger coach is investigated using a multibody system in which the wheelsets and the rails can be modelled as flexible bodies. By comparing the results for different model variants, in which the structural flexibilities of the wheelsets and of the rails are either taken into account or neglected, the impact of the flexibilities is analysed. It turns out that the flexibilities of both the wheelsets and the rails have a significant impact on the hunting behaviour by increasing the lateral motions of the wheelsets and lowering the critical speed. In order to investigate the impact of the flexibilities under different operating conditions, the calculations are carried out for track geometries using different rail profiles (60E1, 60E2) and different rail cants (1:40, 1:20) and for different values for the friction coefficient (0.25…0.4) at the wheel–rail contact. The results show that the influence of the flexibilities is the strongest for high lateral forces, which occur e.g. for contact geometries leading to high hunting frequencies and for high values of the friction coefficient. The results also show in some cases a strong impact of the flexibilities on the position of the wheel–rail contact on the running surface of the rail, which is of particular interest with respect to wear simulation.