Integrating a simplified emission estimation model and mesoscopic dynamic traffic simulator to efficiently evaluate emission impacts of traffic management strategies

This paper presents a computationally efficient and theoretically rigorous dynamic traffic assignment (DTA) model and its solution algorithm for a number of emerging emissions and fuel consumption related applications that require both effective microscopic and macroscopic traffic stream representations. The proposed model embeds a consistent cross-resolution traffic state representation based on Newell’s simplified kinematic wave and linear car following models. Tightly coupled with a computationally efficient emission estimation package MOVES Lite, a mesoscopic simulation-based dynamic network loading framework DTALite is adapted to evaluate traffic dynamics and vehicle emission/fuel consumption impact of different traffic management strategies.     

An integrated modeling approach for facilitating emission estimations of alternative fueled vehicles

This paper develops an integrated model for reliable estimation of daily vehicle fuel savings and emissions using an integrated traffic emission modeling approach created by incorporating the US Environmental Protection Agency’s vehicle emission model, MOVES, and the PARAMICS microscopic traffic simulation package. A case study is conducted to validate the model using a well-calibrated road network in Greenville, South Carolina. For each transportation fuel considered, both emission and fuel consumption impacts are evaluated based on market shares.     

Fuel consumption and emission modelling by power demand and a comparison with other models

Part 1 describes a fuel consumption model based upon the instantaneous power demand experienced by a vehicle, which has been developed from chassis dynamometer experiments on 177 in-use Australian vehicles. When applied to an individual vehicle, the model provides aggregate fuel consumption estimates for on-road driving which are within 2% of the actual measured fuel usage. Emission rate models for hydrocarbons and nitrogen oxides which are of the same form as the fuel consumption model are also presented. The vehicle model can be applied in any traffic situation provided on-road power demand is known. On-road instantaneous power demand is derived from the vehicle's mass, drag, velocity acceleration and road gradient. In the first part 1929 km and 2778 links of traffic driving pattern data for both urban and non-urban trips are presented. Correlations between the link power and traffic parameters are presented and it is shown that vehicle link fuel consumption and emissions can be accurately calculated from vehicle mass, engine capacity, link average velocity, link average positive inertial power, link altitude change and link trip time. In the non-urban case, link power, and hence fuel consumption and emissions, are not dependent upon positive inertial power. In Part 2 the instantaneous vehicle power demand model is used to develop fuel usage input information to evaluate a simple average velocity model and an elemental model. The performance of these two models is compared with that of the on-road power method by “driving” all three models over 2281 links and 956 km of recorded on-road velocity, acceleration and gradient data. It is shown that all three models can be made to perform well for long trips. The elemental model, however, suffers from an inability to adequately describe the fuel usage of different stop-start manoeuvres and requires some calibration in order to account for cruise speed fluctuations. For short trips, 3.5 km in length or less, the on-road power demand method is superior. Under these conditions, both the simple V̄ and elemental models are unable to adequately describe the fuel usage relating to inertial power demands. It is shown that for short trips, inertial power demand does not correlate with average velocity and may range from near zero to up to twice the total trip averaged power.     

Evaluating the impacts of urban corridor traffic signal optimization on vehicle emissions and fuel consumption

This study investigates the impacts of traffic signal timing optimization on vehicular fuel consumption and emissions at an urban corridor. The traffic signal optimization approach proposed integrates a TRANSIMS microscopic traffic simulator, the VT-Micro model (a microscopic emission and fuel consumption estimation model), and a genetic algorithm (GA)-based optimizer. An urban corridor consisting of four signalized intersections in Charlottesville, VA, USA, is used for a case study. The result of the case study is then compared with the best traffic signal timing plan generated by Synchro using the TRANSIMS microscopic traffic simulator. The proposed approach achieves much better performance than that of the best Synchro solution in terms of air quality, energy and mobility measures: 20% less network-wide fuel consumption, 8–20% less vehicle emissions, and nearly 27% less vehicle-hours-traveled (VHT).     

Improving fuel consumption and CO2 emissions calculations in urban areas by coupling a dynamic micro traffic model with an instantaneous emissions model

Τhis study demonstrates the combination of a microscopic traffic simulator (AIMSUN) with an instantaneous emissions model (AVL CRUISE) to investigate the impact of traffic congestion on fuel consumption on an urban arterial road. The micro traffic model was enhanced by an improved car-following law according to Morello et al. (2014) and was calibrated to replicate measured driving patterns over an urban corridor in Turin, Italy, operating under adaptive urban traffic control (UTC). The method was implemented to study the impact of congestion on fuel consumption for the category of Euro 5 diesel <1.4 l passenger cars. Free flow and congested conditions led to respective consumption differences of −25.8% and 20.9% over normal traffic. COPERT 5 rather well predicted the impact of congestion but resulted to a much lower relative reduction in free flow conditions. Start and stop system was estimated to reduce consumption by 6% and 11.9% under normal and congested conditions, respectively. Using the same modelling approach, UTC was found to have a positive impact on CO₂ emissions of 8.1% and 4.5% for normal and congested conditions, respectively, considering the Turin vehicle fleet mix for the year 2013. Overall, the study demonstrates that the combination of detailed and validated micro traffic and emissions models offers a powerful combination to study traffic and powertrain impacts on greenhouse gas and fuel consumption of on road vehicles over a city network.     

Mobility and environment improvement of signalized networks through Vehicle-to-Infrastructure (V2I) communications

Traffic signals, even though crucial for safe operations of busy intersections, are one of the leading causes of travel delays in urban settings, as well as the reason why billions of gallons of fuel are burned, and tons of toxic pollutants released to the atmosphere each year by idling engines. Recent advances in cellular networks and dedicated short-range communications make Vehicle-to-Infrastructure (V2I) communications a reality, as individual cars and traffic signals can now be equipped with communication and computing devices. In this paper, we first presented an integrated simulator with V2I, a car-following model and an emission model to simulate the behavior of vehicles at signalized intersections and calculate travel delays in queues, vehicle emissions, and fuel consumption. We then present a hierarchical green driving strategy based on feedback control to smooth stop-and-go traffic in signalized networks, where signals can disseminate traffic signal information and loop detector data to connected vehicles through V2I communications. In this strategy, the control variable is an individual advisory speed limit for each equipped vehicle, which is calculated from its location, signal settings, and traffic conditions. Finally, we quantify the mobility and environment improvements of the green driving strategy with respect to market penetration rates of equipped vehicles, traffic conditions, communication characteristics, location accuracy, and the car-following model itself, both in isolated and non-isolated intersections. In particular, we demonstrate savings of around 15% in travel delays and around 8% in fuel consumption and greenhouse gas emissions. Different from many existing ecodriving strategies in signalized road networks, where vehicles’ speed profiles are totally controlled, our strategy is hierarchical, since only the speed limit is provided, and vehicles still have to follow their leaders. Such a strategy is crucial for maintaining safety with mixed vehicles.     

Connectivity-based optimization of vehicle route and speed for improved fuel economy

Traditionally, vehicle route planning problem focuses on route optimization based on traffic data and surrounding environment. This paper proposes a novel extended vehicle route planning problem, called vehicle macroscopic motion planning (VMMP) problem, to optimize vehicle route and speed simultaneously using both traffic data and vehicle characteristics to improve fuel economy for a given expected trip time. The required traffic data and neighbouring vehicle dynamic parameters can be collected through the vehicle connectivity (e.g. vehicle-to-vehicle, vehicle-to-infrastructure, vehicle-to-cloud, etc.) developed rapidly in recent years. A genetic algorithm based co-optimization method, along with an adaptive real-time optimization strategy, is proposed to solve the proposed VMMP problem. It is able to provide the fuel economic route and reference speed for drivers or automated vehicles to improve the vehicle fuel economy. A co-simulation model, combining a traffic model based on SUMO (Simulation of Urban MObility) with a Simulink powertrain model, is developed to validate the proposed VMMP method. Four simulation studies, based on a real traffic network, are conducted for validating the proposed VMMP: (1) ideal traffic environment without traffic light and jam for studying the fuel economy improvement, (2) traffic environment with traffic light for validating the proposed traffic light penalty model, (3) traffic environment with traffic light and jam for validating the proposed adaptive real-time optimization strategy, and (4) investigating the effect of different powertrain platforms to fuel economy using two different vehicle platforms. Simulation results show that the proposed VMMP method is able to improve vehicle fuel economy significantly. For instance, comparing with the fastest route, the fuel economy using the proposed VMMP method is improved by up to 15%.     

Hardware-in-the-loop testbed for evaluating connected vehicle applications

Connected vehicle environment provides the groundwork of future road transportation. Researches in this area are gaining a lot of attention to improve not only traffic mobility and safety, but also vehicles’ fuel consumption and emissions. Energy optimization methods that combine traffic information are proposed, but actual testing in the field proves to be rather challenging largely due to safety and technical issues. In light of this, a Hardware-in-the-Loop-System (HiLS) testbed to evaluate the performance of connected vehicle applications is proposed. A laboratory powertrain research platform, which consists of a real engine, an engine-loading device (hydrostatic dynamometer) and a virtual powertrain model to represent a vehicle, is connected remotely to a microscopic traffic simulator (VISSIM). Vehicle dynamics and road conditions of a target vehicle in the VISSIM simulation are transmitted to the powertrain research platform through the internet, where the power demand can then be calculated. The engine then operates through an engine optimization procedure to minimize fuel consumption, while the dynamometer tracks the desired engine load based on the target vehicle information. Test results show fast data transfer at every 200 ms and good tracking of the optimized engine operating points and the desired vehicle speed. Actual fuel and emissions measurements, which otherwise could not be calculated precisely by fuel and emission maps in simulations, are achieved by the testbed. In addition, VISSIM simulation can be implemented remotely while connected to the powertrain research platform through the internet, allowing easy access to the laboratory setup.     

A platoon based cooperative eco-driving model for mixed automated and human-driven vehicles at a signalised intersection

The advancements in communication and sensing technologies can be exploited to assist the drivers in making better decisions. In this paper, we consider the design of a real-time cooperative eco-driving strategy for a group of vehicles with mixed automated vehicles (AVs) and human-driven vehicles (HVs). The lead vehicles in the platoon can receive the signal phase and timing information via vehicle-to-infrastructure (V2I) communication and the traffic states of both the preceding vehicle and current platoon via vehicle-to-vehicle (V2V) communication. We propose a receding horizon model predictive control (MPC) method to minimise the fuel consumption for platoons and drive the platoons to pass the intersection on a green phase. The method is then extended to dynamic platoon splitting and merging rules for cooperation among AVs and HVs in response to the high variation in urban traffic flow. Extensive simulation tests are also conducted to demonstrate the performance of the model in various conditions in the mixed traffic flow and different penetration rates of AVs. Our model shows that the cooperation between AVs and HVs can further smooth out the trajectory of the latter and reduce the fuel consumption of the entire traffic system, especially for the low penetration of AVs. It is noteworthy that the proposed model does not compromise the traffic efficiency and the driving comfort while achieving the eco-driving strategy.     

A field evaluation case study of the environmental and energy impacts of traffic calming

This study quantifies the energy and environmental impact of a selection of traffic calming measures using a combination of second-by-second floating-car global positioning system data and microscopic energy and emission models. It finds that traffic calming may result in negative impacts on vehicle fuel consumption and emission rates if drivers exert aggressive acceleration levels to speed up to their journeys. Consequently by eliminating sharp acceleration maneuvers significant savings in vehicle fuel consumption and emission rates are achievable through driver education. The study also demonstrates that high emitting vehicles produce CO emissions that are up to 25 times higher than normal vehicle emission levels while low emitting vehicles produce emissions that are 15–35% of normal vehicles. The relative increases in vehicle fuel consumption and emission levels associated with the sample traffic calming measures are consistent and similar for normal, low, and high emitting vehicles.     

A trajectory smoothing method at signalized intersection based on individualized variable speed limits with location optimization

Traffic signals on urban highways force vehicles to stop frequently and thus causes excessive travel delay, extra fuel consumption and emissions, and increased safety hazards. To address these issues, this paper proposes a trajectory smoothing method based on Individual Variable Speed Limits with Location Optimization (IVSL-LC) in coordination with pre-fixed traffic signals. This method dynamically imposes speed limits on some identified Target Controlled Vehicles (TCVs) with Vehicle to Infrastructures (V2I) communication ability at two IVSL points along an approaching lane. According to real-time traffic demand and signal timing information, the trajectories of each approaching vehicle are made to run smoothly without any full stop. Essentially, only TCVs’ trajectories need to be controlled and the other vehicles just follow TCVs with Gipps’ car-following model. The Dividing RECTangles (DIRECT) algorithm is used to optimize the locations of the IVSLs. Numerical simulation is conducted to compare the benchmark case without vehicle control, the individual advisory speed limits (IASL) and the proposed IVSL-LC. The result shows that compared with the benchmark, the IVSL-LC method can greatly increase traffic efficiency and reduce fuel consumption. Compared with IASL, IVSL-LC has better performance across all traffic demand levels, and the improvements are the most under high traffic demand. Finally, the results of compliance analysis show that the effect of IVSL-LC improves as the compliance rate increases.     

Stop-and-go traffic analysis: Theoretical properties,environmental impacts and oscillation mitigation

This study aims (i) to analyze theoretical properties of a recently proposed describing-function (DF) based approach (Li and Ouyang, 2011; Li et al., 2012) for traffic oscillation quantification, (ii) to adapt it for estimating fuel consumption and emission from traffic oscillation and (iii) to explore vehicle control strategies of smoothing traffic with advanced technologies. The DF approach was developed to predict traffic oscillation propagation across a platoon of vehicles following each other by a nonlinear car-following law with only the leading vehicle’s input. We first simplify the DF approach and prove a set of properties (e.g., existence and uniqueness of its solution) that assure its prediction is always consistent with observed traffic oscillation patterns. Then we integrate the DF approach with existing estimation models of fuel consumption and emission to analytically predict environmental impacts (i.e., unit-distance fuel consumption and emission) from traffic oscillation. The prediction results by the DF approach are validated with both computer simulation and field measurements. Further, we explore how to utilize advantageous features of emerging sensing, communication and control technologies, such as fast response and information sharing, to smooth traffic oscillation and reduce its environmental impacts. We extend the studied car-following law to incorporate these features and apply the DF approach to demonstrate how these features can help dampen the growth of oscillation and environmental impact measurements. For information sharing, we convert the corresponding extended car-following law into a new fixed point problem and propose a simple bisecting based algorithm to efficiently solve it. Numerical experiments show that these new car-following control strategies can effectively suppress development of oscillation amplitude and consequently mitigate fuel consumption and emission.     

Does traffic-related calibration of car-following models provide accurate estimations of vehicle emissions?

Fuel consumption or pollutant emissions can be assessed by coupling a microscopic traffic flow model with an instantaneous emission model. Traffic models are usually calibrated using goodness of fit indicators related to the traffic behavior. Thus, this paper investigates how such a calibration influences the accuracy of fuel consumption and NOx and PM estimations. Two traffic models are investigated: Newell and Gipps. It appears that the Gipps model provides the closest simulated trajectories when compared to real ones. Interestingly, a reverse ranking is observed for fuel consumption, NOx and PM emissions. For both models, the emissions of single vehicles are very sensitive to the calibration. This is confirmed by a global sensitivity analysis of the Gipps model that shows that non-optimal parameters significantly increase the variance of the outputs. Fortunately, this is no longer the case when emissions are calculated for a group of many vehicles. Indeed, the mean errors for platoons are close to 10% for the Gipps model and always lower than 4% for the Newell model. Another interesting property is that optimal parameters for each vehicle can be replaced by the mean values with no discrepancy for the Newell model and low discrepancies for the Gipps model when calculating the different emission outputs. Finally, this study presents preliminary results that show that multi-objective calibration methods are certainly the best direction for future works on the Gipps model. Indeed, the accuracy of vehicle emissions can be highly improved with negligible counterparts on the traffic model accuracy.     

Optimal vehicle speed trajectory on a signalized arterial with consideration of queue

Vehicle speed trajectory significantly impacts fuel consumption and greenhouse gas emissions, especially for trips on signalized arterials. Although a large amount of research has been conducted aiming at providing optimal speed advisory to drivers, impacts from queues at intersections are not considered. Ignoring the constraints induced by queues could result in suboptimal or infeasible solutions. In this study, a multi-stage optimal control formulation is proposed to obtain the optimal vehicle trajectory on signalized arterials, where both vehicle queue and traffic light status are considered. To facilitate the real-time update of the optimal speed trajectory, a constrained optimization model is proposed as an approximation approach, which can be solved much quicker. Numerical examples demonstrate the effectiveness of the proposed optimal control model and the solution efficiency of the proposed approach.     

A control theoretic formulation of green driving strategies based on inter-vehicle communications

Various green driving strategies have been proposed to smooth traffic flow and lower pollutant emissions and fuel consumption in stop-and-go traffic. In this paper, we present a control theoretic formulation of distributed, cooperative green driving strategies based on inter-vehicle communications (IVCs). The control variable is the advisory speed limit, which is designed to smooth a following vehicle’s speed profile without changing its average speed. We theoretically analyze the performance of a constant independent and three simple cooperative green driving strategies and present three rules for effective and robust strategies. We then develop a distributed cooperative green driving strategy, in which the advisory speed limit is first independently calculated by each individual vehicle and then averaged among green driving vehicles through IVC. By simulations with Newell’s car-following model and the Comprehensive Modal Emissions Model (CMEM), we demonstrate that such a strategy is effective and robust independently as well as cooperatively for different market penetration rates of IVC-equipped vehicles and communication delays. In particular, even when 5% of the vehicles implement the green driving strategy and the IVC communication delay is 60 s, the fuel consumption can be reduced by up to 15%. Finally we discuss some future extensions.     

Spatiotemporal intersection control in a connected and automated vehicle environment

Current research on traffic control has focused on the optimization of either traffic signals or vehicle trajectories. With the rapid development of connected and automated vehicle (CAV) technologies, vehicles equipped with dedicated short-range communications (DSRC) can communicate not only with other CAVs but also with infrastructure. Joint control of vehicle trajectories and traffic signals becomes feasible and may achieve greater benefits regarding system efficiency and environmental sustainability. Traffic control framework is expected to be extended from one dimension (either spatial or temporal) to two dimensions (spatiotemporal). This paper investigates a joint control framework for isolated intersections. The control framework is modeled as a two-stage optimization problem with signal optimization at the first stage and vehicle trajectory control at the second stage. The signal optimization is modeled as a dynamic programming (DP) problem with the objective to minimize vehicle delay. Optimal control theory is applied to the vehicle trajectory control problem with the objective to minimize fuel consumption and emissions. A simplified objective function is adopted to get analytical solutions to the optimal control problem so that the two-stage model is solved efficiently. Simulation results show that the proposed joint control framework is able to reduce both vehicle delay and emissions under a variety of demand levels compared to fixed-time and adaptive signal control when vehicle trajectories are not optimized. The reduced vehicle delay and CO₂ emissions can be as much as 24.0% and 13.8%, respectively for a simple two-phase intersection. Sensitivity analysis suggests that maximum acceleration and deceleration rates have a significant impact on the performance regarding both vehicle delay and emission reduction. Further extension to a full eight-phase intersection shows a similar pattern of delay and emission reduction by the joint control framework.     

Hierarchical control strategies for energy management of connected hybrid electric vehicles in urban roads

This paper presents a fuel efficient control strategy for a group of connected hybrid electric vehicles (HEVs) in urban road conditions. A hierarchical control architecture is proposed in this paper for every HEV, where the higher level and the lower level controller share information with each other and solve two different problems that aim at improving its fuel efficiency. The higher level controller of each HEV is considered to utilize traffic light information, through vehicle to infrastructure (V2I) communication, and state information of the vehicles in its near neighborhood, via vehicle to vehicle (V2V) communication. Apart from that, the higher level controller of each HEV uses the recuperation information from the lower level controller and provides it the optimal velocity profile by solving its problem in a model predictive control framework. Each lower level controller uses adaptive equivalent consumption minimization strategy (ECMS) for following their velocity profiles, obtained from the higher level controller, in a fuel efficient manner. In this paper, the vehicles are modeled in Autonomie software and the simulation results are provided in the paper that shows the effectiveness of the proposed control architecture.     

香港典型山区道路汽车行驶工况污染物排放研究

通过安装车载测试系统收集香港港岛山区路段正常行驶工况下尾气中的CO、NOx、HC等污染物和油耗并辅助计算机软件进行分析。研究得出,山区道路设计、地形地貌和驾驶习惯对车辆油耗以及CO、NOx和HC排放有直接关系。可以通过坡道加宽、坡道延长、减少坡道红绿灯等措施减少车辆在山区道路行驶过程中速度变化频率,从而减少油耗以及CO、NOx和HC排放。     

The impacts of connected vehicle technology on network-wide traffic operation and fuel consumption under various incident scenarios

ABSTRACT

Incidents are a major source of traffic congestion and can lead to long and unpredictable delays, deteriorating traffic operations and adverse environmental impacts. The emergence of connected vehicles and communication technologies has enabled travelers to use real-time traffic information. The ability to exchange traffic information among vehicles has tremendous potential impacts on network performance especially in the case of non-recurrent congestion. To this end, this paper utilizes a microscopic simulation model of traffic in El Paso, Texas to investigate the impacts of incidents on traffic operation and fuel consumption at different market penetration rates (MPR) of connected vehicles. Several scenarios are implemented and tested to determine the impacts of incidents on network performance in an urban area. The scenarios are defined by changing the duration of incidents and the number of lanes closed. This study also shows how communication technology affects network performance in response to congestion. The results of the study demonstrate the potential effectiveness of connected vehicle technology in improving network performance. For an incident with a duration of 900?s and MPR of 80%, total fuel consumption and total travel time decreased by approximately 20%; 26% was observed in network-wide travel time and fuel consumption at 100% MPR.     

Modeling of individual vehicle safety and fuel consumption under comprehensive external conditions

This research intends to explore external factors affecting driving safety and fuel consumption, and build a risk and fuel consumption prediction model for individual drivers based on natural driving data. Based on 120 taxi drivers’ natural driving data during 4 months, driving behavior data under various conditions of the roadway, traffic, weather, and time of day are extracted. The driver's fuel consumption is directly collected by the on-board diagnostics (OBD) unit, and safety index is calculated based on Data Threshold Violations (DTV) and Phase Plane Analysis with Limits (PPAL) considering speed, longitudinal and lateral acceleration. By using a linear mixed model explaining the fixed effect of the external conditions and the random effect of the driver, the influences of various external factors on fuel consumption and safety are analyzed and discussed. The prediction model lays a foundation for drivers' fuel consumption and risk prediction in different external conditions, which could help improve individual driving behavior for the benefit of both fuel consumption and safety.