共查询到20条相似文献，搜索用时 15 毫秒
2.
This contribution furthers the control framework for driver assistance systems in Part I to cooperative systems, where equipped vehicles can exchange relevant information via vehicle-to-vehicle communication to improve the awareness of the ambient situation (cooperative sensing) and to manoeuvre together under a common goal (cooperative control). To operationalize the cooperative sensing strategy, the framework is applied to the development of a multi-anticipative controller, where an equipped vehicle uses information from its direct predecessor to predict the behaviour of its pre-predecessor. To operationalize the cooperative control strategy, we design cooperative controllers for sequential equipped vehicles in a platoon, where they collaborate to optimise a joint objective. The cooperative control strategy is not restricted to cooperation between equipped vehicles. When followed by a human-driven vehicle, equipped vehicles can still exhibit cooperative behaviour by predicting the behaviour of the human-driven follower, even if the prediction is not perfect.The performance of the proposed controllers are assessed by simulating a platoon of 11 vehicles with reference to the non-cooperative controller proposed in Part I. Evaluations show that the multi-anticipative controller generates smoother behaviour in accelerating phase. By a careful choice of the running cost specification, cooperative controllers lead to smoother decelerating behaviour and more responsive and agile accelerating behaviour compared to the non-cooperative controller. The dynamic characteristics of the proposed controllers provide new insights into the potential impact of cooperative systems on traffic flow operations, particularly at the congestion head and tail. 相似文献
3.
Vehicle longitudinal control systems such as (commercially available) autonomous Adaptive Cruise Control (ACC) and its more sophisticated variant Cooperative ACC (CACC) could potentially have significant impacts on traffic flow. Accurate models of the dynamic responses of both of these systems are needed to produce realistic predictions of their effects on highway capacity and traffic flow dynamics. This paper describes the development of models of both ACC and CACC control systems that are based on real experimental data. To this end, four production vehicles were equipped with a commercial ACC system and a newly developed CACC controller. The Intelligent Driver Model (IDM) that has been widely used for ACC car-following modeling was also implemented on the production vehicles. These controllers were tested in different traffic situations in order to measure the actual responses of the vehicles. Test results indicate that: (1) the IDM controller when implemented in our experimental test vehicles does not perceptibly follow the speed changes of the preceding vehicle; (2) strings of consecutive ACC vehicles are unstable, amplifying the speed variations of preceding vehicles; and (3) strings of consecutive CACC vehicles overcome these limitations, providing smooth and stable car following responses. Simple but accurate models of the ACC and CACC vehicle following dynamics were derived from the actual measured responses of the vehicles and applied to simulations of some simple multi-vehicle car following scenarios. 相似文献
4.
This paper introduces Simulation of Intelligent TRAnsport Systems (SITRAS), a massive multi-agent simulation system in which driver-vehicle objects are modelled as autonomous agents. The simulation outputs can be used for the evaluation of Intelligent Transport Systems applications such as congestion and incident management, public transport priority and dynamic route guidance. The model concepts and specifications, and the first applications of the model in the area of incident modelling in urban arterial networks were described in previous publications. This paper presents the details of the lane changing and merging algorithms developed for the SITRAS model. These models incorporate procedures for ‘forced’ and ‘co-operative’ lane changing which are essential for lane changing under congested (and incident-affected) traffic conditions. The paper describes the algorithms and presents simulation examples to demonstrate the effects of the implemented models. The results indicate that only the forced and cooperative lane changing models can produce realistic flow-speed relationships during congested conditions. 相似文献
5.
Fully automated vehicles could have a significant share of the road network traffic in the near future. Several commercial vehicles with full-range Adaptive Cruise Control (ACC) systems or semi-autonomous functionalities are already available on the market. Many research studies aim at leveraging the potential of automated driving in order to improve the fuel efficiency of vehicles. However, in the vast majority of those, fuel efficiency is isolated to the driving dynamics between a single follower-leader pair, hence overlooking the complex nature of traffic. Consequently fuel efficiency and the efficient use of the roadway capacity are framed as conflicting objectives, leading to fuel-economy control models that adopt highly conservative driving styles.This formulation of the problem could be seen as a user-optimal approach, where in spite of delivering savings for individual vehicles, there is the side-effect of the deterioration of traffic flow. An important point that is overlooked is that the inefficient use of roadway capacity gives rise to congested traffic and traffic breakdowns, which in return increases energy costs within the system. The optimisation methods used in these studies entail high computational costs and, therefore, impose a strict constraint on the scope of problem.In this study, the use of car-following models and the limitation of the search space of optimal strategies to the parameter space of these is proposed. The proposed framework enables performing much more comprehensive optimisations and conducting more extensive tests on the collective impacts of fuel-economy driving strategies. The results show that, as conjectured, a “short-sighted” user-optimal approach is unable to deliver overall fuel efficiency. Conversely, a system-optimal formulation for fuel efficient driving is presented, and it is shown that the objectives of fuel efficiency and traffic flow are in fact not only non-conflicting, but also that they could be viewed as one when the global benefits to the network are considered. 相似文献
6.
Bin Ran Shawn Leight Ben Chang 《Transportation Research Part C: Emerging Technologies》1999,7(6):369-388
The automated highway systems (AHS) are not designed as stand-alone transportation facilities. Drivers will by necessity drive from their origins to the AHS entrance, and from the AHS exit to their final destinations. Therefore, the AHS will affect other transportation facilities, and should be integrated with all other facilities in the transportation system. Interfaces create much of the congestion for today’s transportation systems. Likewise, AHS interfaces may cause a similar problem, due to either AHS interactions with conventional systems or internal limitations from AHS merging capabilities. If these problems exist, either the AHS or the conventional road network cannot function properly. Consequently, the system as a whole may break down and the AHS could potentially become a detriment to the overall transportation system.Clearly, not enough is known about the automated merging process to determine what conditions would lead to congestion at interface points. The current macroscopic analysis techniques assume parameters that are not applicable to an AHS, and no detailed AHS merging models have been developed and validated. This paper addresses the interface problem between an AHS, and conventional roadway. Specifically, it presents a microscopic simulation model for one scenario of the automated merging maneuver. The results of the model show that for low flows and conventional highway speeds, an one-lane AHS merging section with a dedicated automated entrance ramp has many similar characteristics as a two-lane conventional freeway with or without fixed-time ramp metering. However, when the conventional freeway starts to “break down” near its capacity, the AHS continues to perform with little delay. The model also validates that the minimum ramp length requirements are a function of the merging vehicle’s speed, the mainline vehicles’ speed, and the acceleration and deceleration rates of the merging vehicle. 相似文献
7.
Adaptive Cruise Control systems have been developed and introduced into the consumer market for over a decade. Among these systems, fully-adaptive ones are required to adapt their behaviour not only to traffic conditions but also to drivers’ preferences and attitudes, as well as to the way such preferences change for the same driver in different driving sessions. This would ideally lead towards a system where an on-board electronic control unit can be asked by the driver to calibrate its own parameters while he/she manually drives for a few minutes (learning mode). After calibration, the control unit switches to the running mode where the learned driving style is applied. The learning mode can be activated by any driver of the car, for any driving session and each time he/she wishes to change the current driving behaviour of the cruise control system.The modelling framework which we propose to implement comprises four layers (sampler, profiler, tutor, performer). The sampler is responsible for human likeness and can be calibrated while in learning mode. Then, while in running mode, it works together with the other modelling layers to implement the logic. This paper presents the overall framework, with particular emphasis on the sampler and the profiler that are explained in full mathematical detail. Specification and calibration of the proposed framework are supported by the observed data, collected by means of an instrumented vehicle. The data are also used to assess the proposed framework, confirming human-like and fully-adaptive characteristics. 相似文献
8.
Variable speed limit systems where variable message signs are used to show speed limits adjusted to the prevailing road or traffic conditions are installed on motorways in many countries. The objectives of variable speed limit system installations are often to decrease the number of accidents and to increase traffic efficiency. Currently, there is an interest in exploring the potential of cooperative intelligent transport systems including communication between vehicles and/or vehicles and the infrastructure. In this paper, we study the potential benefits of introducing infrastructure to vehicle communication, autonomous vehicle control and individualized speed limits in variable speed limit systems. We do this by proposing a cooperative variable speed limit system as an extension of an existing variable speed limit system. In the proposed system, communication between the infrastructure and the vehicles is used to transmit variable speed limits to upstream vehicles before the variable message signs become visible to the drivers. The system is evaluated by the means of microscopic traffic simulation. Traffic efficiency and environmental effects are considered in the analysis. The results of the study show benefits of the infrastructure to vehicle communication, autonomous vehicle control and individualized speed limits for variable speed limit systems in the form of lower acceleration rates and thereby harmonized traffic flow and reduced exhaust emissions. 相似文献
9.
10.
Work zones on motorways necessitate the drop of one or more lanes which may lead to significant reduction of traffic flow capacity and efficiency, traffic flow disruptions, congestion creation, and increased accident risk. Real-time traffic control by use of green–red traffic signals at the motorway mainstream is proposed in order to achieve safer merging of vehicles entering the work zone and, at the same time, maximize throughput and reduce travel delays. A significant issue that had been neglected in previous research is the investigation of the impact of distance between the merge area and the traffic lights so as to achieve, in combination with the employed real-time traffic control strategy, the most efficient merging of vehicles. The control strategy applied for real-time signal operation is based on an ALINEA-like proportional–integral (PI-type) feedback regulator. In order to achieve maximum performance of the control strategy, some calibration of the regulator’s parameters may be necessary. The calibration is first conducted manually, via a typical trial-and-error procedure. In an additional investigation, the recently proposed learning/adaptive fine-tuning (AFT) algorithm is employed in order to automatically fine-tune the regulator parameters. Experiments conducted with a microscopic simulator for a hypothetical work zone infrastructure, demonstrate the potential high benefits of the control scheme. 相似文献
11.
This paper presents a thorough microscopic simulation investigation of a recently proposed methodology for highway traffic estimation with mixed traffic, i.e., traffic comprising both connected and conventional vehicles, which employs only speed measurements stemming from connected vehicles and a limited number (sufficient to guarantee observability) of flow measurements from spot sensors. The estimation scheme is tested using the commercial traffic simulator Aimsun under various penetration rates of connected vehicles, employing a traffic scenario that features congested as well as free-flow conditions. The case of mixed traffic comprising conventional and connected vehicles equipped with adaptive cruise control, which feature a systematically different car-following behavior than regular vehicles, is also considered. In both cases, it is demonstrated that the estimation results are satisfactory, even for low penetration rates. 相似文献
12.
Ludovic Leclercq Jorge A. LavalNicolas Chiabaut 《Transportation Research Part B: Methodological》2011,45(9):1302-1313
The Newell-Daganzo merge model is not only very simple but also accurately reproduces experimental findings. However, the capacity downstream of the merge is an exogenous variable in the model. This is a serious limitation for merges that behave as active bottlenecks because their downstream capacity is a direct consequence of the merging behavior. This paper proposes an analytical model that extends the Newell-Daganzo model by incorporating, endogenously, the capacity drop related to the merging process. Two cases are investigated depending on the traffic states on the on-ramp. The model properties are analyzed and a sensitivity analysis is performed to quantify the relative contribution of the each parameter in the capacity drop. Finally, the extended Newell-Daganzo model is validated with experimental data coming from an active merge bottleneck on the M6 freeway in UK. 相似文献
13.
Traffic flow optimization and driver comfort enhancement are the main contributions of an Adaptive Cruise Control (ACC) system. If communication links are added, more safety and shorter gaps can be reached performing a Cooperative-ACC (CACC). Although shortening the inter-vehicular distances directly improves traffic flow, it can cause string unstable behavior. This paper presents fractional-order-based control algorithms to enhance the car-following and string stability performance for both ACC and CACC vehicle strings, including communication temporal delay effects. The proposed controller is compared with state-of-the-art implementations, exhibiting better performance. Simulation and real experiments have been conducted for validating the approach. 相似文献
14.
Arne Kesting Martin Treiber Martin Schnhof Dirk Helbing 《Transportation Research Part C: Emerging Technologies》2008,16(6):668-683
We present an adaptive cruise control (ACC) strategy where the acceleration characteristics, that is, the driving style automatically adapts to different traffic situations. The three components of the concept are the ACC itself, implemented in the form of a car-following model, an algorithm for the automatic real-time detection of the traffic situation based on local information, and a strategy matrix to adapt the driving characteristics (that is, the parameters of the ACC controller) to the traffic conditions. Optionally, inter-vehicle and infrastructure-to-car communication can be used to improve the accuracy of determining the traffic states. Within a microscopic simulation framework, we have simulated the complete concept on a road section with an on-ramp bottleneck, using empirical loop-detector data for an afternoon rush-hour as input for the upstream boundary. We found that the ACC vehicles improve the traffic stability and the dynamic road capacity. While traffic congestion in the reference scenario was completely eliminated when simulating a proportion of 25% ACC vehicles, travel times were already significantly reduced for much lower penetration rates. The efficiency of the proposed driving strategy even for low market penetrations is a promising result for a successful application in future driver assistance systems. 相似文献
15.
Elvezia M. Cepolina 《运输规划与技术》2013,36(3):145-180
Evaluation of accessibility is of increasing importance to the design of the public realm – including both the built and moving environments and particularly the interface between them. This is of particular relevance to people who are living on the ‘margins of accessibility’, for example, elderly or disabled people. This paper discusses the interactions between a person, the environment and the activities they wish to pursue, and proposes a model that incorporates the concept of ‘capabilities’. The paper then describes how the systematization of these concepts could be tested by incorporating them in a microscopic simulation model of pedestrian activity. A worked example is used to demonstrate how the conceptual approach could yield consistent results under these circumstances. The paper concludes that the conceptual model provides a good basis for the evaluation of accessibility and that the microscopic simulation model incorporating these characteristics would be a useful way of testing pedestrian–environment interactions. 相似文献
16.
Johan Olstam Stéphane Espié Selina Måardh Jonas Jansson Jan Lundgren 《Transportation Research Part C: Emerging Technologies》2011,19(6):1185-1201
Autonomous vehicles can be used to create realistic simulations of surrounding vehicles in driving simulators. However, the use of autonomous vehicles makes it difficult to ensure reproducibility between subjects. In this paper, an effort is made to solve the problem by combining autonomous vehicles and controlled events. A controlled event can be compared to a theatre play. The aim is to achieve the same initial play conditions for each subject, which can be problematic since the traffic situation around the subject will be dependent upon each subject’s actions while driving in autonomous traffic. This paper presents an algorithm that achieves the transition from autonomous traffic to a predefined start condition for a play. The algorithm has been tested in the Swedish National Road and Transport Research Institute (VTI) driving simulator III with promising results. In most of the cases we examined the algorithm could reconstruct the specified start condition and conduct the transition from autonomous to controlled mode in a inconspicuous way. Some problems were observed regarding moving unwanted vehicles away from the closest area around the simulator vehicle, and this part of the algorithm has to be enhanced. The experiment also showed that the subjects drove faster in the presence of controlled everyday life traffic normally used in the VTI driving simulator than in autonomous traffic. 相似文献
17.
In an effort to uncover traffic conditions that trigger discharge rate reductions near active bottlenecks, this paper analyzed individual vehicle trajectories at a microscopic level and documented the findings. Based on an investigation of traffic flow involving diverse traffic situations, a driver’s tendency to take a significant headway after passing stop-and-go waves was identified as one of the influencing factors for discharge rate reduction. Conversely, the pattern of lane changers caused a transient increase in the discharge rate until the situation was relaxed after completing the lane-changing event. Although we observed a high flow from the incoming lane changers, the events ultimately caused adverse impacts on the traffic such that the disturbances generated stop-and-go waves. Based on this observation, we regard upstream lane changes and stop-and-go waves as the responsible factors for the decreased capacity at downstream of active bottlenecks. This empirical investigation also supports the resignation effect, the regressive effect, and the asymmetric behavioral models in differentiating acceleration and deceleration behaviors. 相似文献
18.
Use of traffic simulation has increased in recent decades; and this high-fidelity modelling, along with moving vehicle animation, has allowed transportation decisions to be made with better confidence. During this time, traffic engineers have been encouraged to embrace the process of calibration, in which steps are taken to reconcile simulated and field-observed performance. According to international surveys, experts, and conventional wisdom, existing (non-automated) methods of calibration have been difficult or inadequate. There has been extensive research on improved calibration methods, but many of these efforts have not produced the flexibility and practicality required by real-world engineers. With this in mind, a patent-pending (US 61/859,819) architecture for software-assisted calibration was developed to maximize practicality, flexibility, and ease-of-use. This architecture is called SASCO (i.e. Sensitivity Analysis, Self-Calibration, and Optimization). The original optimization method within SASCO was based on “directed brute force” (DBF) searching; performing exhaustive evaluation of alternatives in a discrete, user-defined search space. Simultaneous Perturbation Stochastic Approximation (SPSA) has also gained favor as an efficient method for optimizing computationally expensive, “black-box” traffic simulations, and was also implemented within SASCO. This paper uses synthetic and real-world case studies to assess the qualities of DBF and SPSA, so they can be applied in the right situations. SPSA was found to be the fastest method, which is important when calibrating numerous inputs, but DBF was more reliable. Additionally DBF was better than SPSA for sensitivity analysis, and for calibrating complex inputs. Regardless of which optimization method is selected, the SASCO architecture appears to offer a new and practice-ready level of calibration efficiency. 相似文献
19.
The capacity drop phenomenon, which reduces the maximum bottleneck discharge rate following the onset of congestion, is a critical restriction in transportation networks that produces additional traffic congestion. Consequently, preventing or reducing the occurrence of the capacity drop not only mitigates traffic congestion, but can also produce environmental and traffic safety benefits. In addressing this problem, the paper develops a novel bang-bang feedback control speed harmonization (SH) or Variable Speed Limit (VSL) algorithm, that attempts to prevent or delay the breakdown of a bottleneck and thus reduce traffic congestion. The novelty of the system lies in the fact that it is both proactive and reactive in responding to the dynamic stochastic nature of traffic. The system is proactive because it uses a calibrated fundamental diagram to initially identify the optimum throughput to maintain within the SH zone. Furthermore, the system is reactive (dynamic) because it monitors the traffic stream directly upstream of the bottleneck to adjustment the metering rate to capture the dynamic and stochastic nature of traffic. The steady-state traffic states in the vicinity of a lane-drop bottleneck before and after applying the SH algorithm is analyzed to demonstrate the effectiveness of the algorithm in alleviating the capacity drop. We demonstrate theoretically that the SH algorithm is effective in enhancing the bottleneck discharge rate. A microscopic simulation of the network using the INTEGRATION software further demonstrates the benefits of the algorithm in increasing the bottleneck discharge rate, decreasing vehicle delay, and reducing vehicle fuel consumption and CO2 emission levels. Specifically, compared with the base case without the SH algorithm, the advisory speed limit increases the bottleneck discharge rate by approximately 7%, reduces the overall system delay by approximately 20%, and reduces the system-wide fuel consumption and CO2 emission levels by 5%. 相似文献
20.
Variable speed limit (VSL) schemes are developed based on the Kinematic Wave theory to increase discharge rates at severe freeway bottlenecks induced by non-recurrent road events such as incidents or work zones while smoothing speed transition. The main control principle is to restrict upstream demand (in free-flow) progressively to achieve three important objectives: (i) to provide gradual speed transition at the tail of an event-induced queue, (ii) to clear the queue around the bottleneck, and (iii) to discharge traffic at the stable maximum flow that can be sustained at the bottleneck without breakdown. These control objectives are accomplished without imposing overly restrictive speed limits. We further provide remedies for (a) underutilized bottleneck capacity due to underestimated stable maximum flow and (b) a re-emergent queue at the bottleneck due to an overestimated stable maximum flow. We analytically formulate the reductions in total delay in terms of control parameters to provide an insight into the system performance and sensitivity. The results from the parameter analysis suggest that significant delay savings can be realized with the proposed VSL control strategies. 相似文献