共查询到20条相似文献,搜索用时 46 毫秒
1.
2.
建立了液力缓速器制动转矩计算模型并对其进行了试验修正,运用修正后的模型就制动性能对叶栅参数的敏感性进行了分析,并以制动转矩为目标,对某型液力缓速器工作轮叶片进出口角度进行优化.结果表明,修正模型的计算结果与试验结果吻合良好,优化后的液力缓速器制动性能显著提高. 相似文献
3.
本文以福伊特液力缓速器为研究对象,通过对液力缓速器的制动性能进行分析,指出影响液力缓速器制动性能的主要因素,为国内液力缓速器的研制开发提供理论依据。 相似文献
4.
液力减速器内流场的CFD数值模拟研究 总被引:2,自引:0,他引:2
用CFD数值模拟技术对液力减速器内部流场进行研究,得到了不同工况下液力减速器内流场的压力和速度分布特性与制动力矩的大小,并对结果进行处理和分析.模拟结果与试验数据的对比表明,流场计算是准确的. 相似文献
5.
6.
7.
重型车液力缓速器制动性能仿真研究 总被引:1,自引:0,他引:1
建立了液力缓速器、行车制动器和整车的数学模型,利用Matlab/simulink组建了重型车制动性能仿真模型,模型包括液力缓速器模块和行车制动系统模块两部分.对液力缓速器各挡位试验、仿真数据分析表明,两者吻合程度较好;紧急制动时的车速、制动距离仿真表明,液力缓速器参与工作时制动效果更明显,从而证明了该仿真模型的正确性. 相似文献
8.
9.
10.
随着运输行业的飞速发展,对运输车辆的运营效率的要求不断提高,导致匹配的发动机功率不断提高。由于传统制动系统受多重因素的限制,制动功效无法提高到同步水平,这对商用车自身的制动性能是非常大的考验。液力缓速器最高能吸收制动能量的90%,可以有效地辅助行车制动系统,故液力缓速器作为商用车制动辅助系统越来越受到人们关注和接受,已逐渐成为重型车辆主流配置。文章以某重卡车型匹配液力缓速器案例为背景,对缓速器布置形式、扭矩大小、冷却水路布置方式的选取进行了理论分析及计算。 相似文献
11.
12.
《Vehicle System Dynamics: International Journal of Vehicle Mechanics and Mobility》2012,50(4):573-596
An existing driver–vehicle model with neuromuscular dynamics is improved in the areas of cognitive delay, intrinsic muscle dynamics and alpha–gamma co-activation. The model is used to investigate the influence of steering torque feedback and neuromuscular dynamics on the vehicle response to lateral force disturbances. When steering torque feedback is present, it is found that the longitudinal position of the lateral disturbance has a significant influence on whether the driver’s reflex response reinforces or attenuates the effect of the disturbance. The response to angle and torque overlay inputs to the steering system is also investigated. The presence of the steering torque feedback reduced the disturbing effect of torque overlay and angle overlay inputs. Reflex action reduced the disturbing effect of a torque overlay input, but increased the disturbing effect of an angle overlay input. Experiments on a driving simulator showed that measured handwheel angle response to an angle overlay input was consistent with the response predicted by the model with reflex action. However, there was significant intra- and inter-subject variability. The results highlight the significance of a driver’s neuromuscular dynamics in determining the vehicle response to disturbances. 相似文献
13.
预应力曲线箱梁和异形箱梁的研究 总被引:7,自引:0,他引:7
近年来 ,国内外学者对曲线箱梁和异形箱梁的静力分析理论和计算方法作过大量的研究 ,但这些理论和方法在某种程度上都存在着一定的局限性 ,特别是在实际设计工作中 ,运用起来不能得心应手。为此本文在综合前人已取得经验下 ,针对桥梁结构设计中分析曲线箱梁、异形箱梁 ,经常遇到的难题进行了研究 ,建立一个较为完善的理论和方法 ,编制了等参元空间分析程序。在实际工程中进行实桥试验 ,验证了本文理论和方法的正确性。本文的研究工作更准确描述了箱梁的荷载响应 ,为设计人员提供直观的设计依据。对曲线箱梁和异形箱梁受力特性有了更一步的理解 ,并提出了新的见解 相似文献
14.
SMA是沥青码蹄脂碎石(Stone Matrix Asphal)的缩写,是一种以沥青结合料与少量的纤维稳定剂、细集料,以及较多的填料(矿粉)组成的沥青玛蹄脂,填充于间断级配粗集料骨架间隙中组成一体所形成的沥青混合料,简称SMA。该文介绍了SMA在上海的应用及其施工技术。 相似文献
15.
混凝土的推广使用已有一个世纪,目前在现代工程建设中仍占有重要的地位。而在今天,混凝土的裂缝较为普遍,在桥梁工程中裂缝几乎无所不在,尽管我们在施工中采取各种各样的措施,但收效甚微,裂缝仍然时有出现。该文指出,究其原因,人们对混凝土温度变化所产生的应力注意不够是其中之一,尤其是大体积混凝土。对此,温度应力与温度控制具有重要的意义。 相似文献
16.
利用AVL公司开发的BOOST软件可宏观地描述发动机的热力学过程且优化发动机的性能,而AVL的CRUISE软件可调用BOOST建立的发动机模型.在进行道路循环工况的仿真时,须对发动机全部工况点进行准确的标定.文中采用BOOST开发了发动机的仿真模型.通过调整节气门开度和燃烧模型参数,标定了发动机在多个转速和负荷点的转矩、功率和油耗,较好地模拟了发动机的动力性和经济性.最后基于ECE循环工况,将此模型与CRUISE进行联合仿真,分析了发动机瞬态工况的动力性、油耗和NO_x排放等参数. 相似文献
17.
J. R. Serrano F. J. Arnau V. Dolz A. Tiseira M. Lejeune N. Auffret 《International Journal of Automotive Technology》2008,9(3):277-288
This article presents a two-stage turbocharged heavy-duty diesel (HDD) engine designed to fulfil the US2007 anti-pollution
directive. This directive imposes very restrictive limits on the NOx and particle emissions of HDD engines. In this work,
the possibility of combining particle traps in the exhaust line to reduce soot emissions with very high EGR rates to reduce
NOx emissions is considered. This new generation engine implements two-stage turbocharging in order to improve the bsfc when
the engine is working on steady conditions as well as to optimize the engine transient response. After carrying out the tests,
the results were analyzed and the engine settings were adjusted to maximise its behaviour and minimise pollutant emissions.
NOx and soot emission peaks were also analyzed at engine transient conditions in order to keep them under certain levels,
and thus maintain the overall pollutant emissions to a level that is as low as possible. In summary, a double-stage turbocharging
configuration can greatly improve engine driveability (between 23% and 36% depending on engine speed), while reducing NOx
emissions during transient evolution without increasing opacity peaks beyond the stated limits. 相似文献
18.
19.
该文从研究超薄磨耗层的级配的选择入手,简单分析了超薄磨耗层的结构特点和强度形成机理,给出了几种国内外常用的超薄磨耗层级配范围,并提出了将SAC-10做为其研究的设计级配。在研究超薄磨耗层沥青混合料配合比设计的基础上,通过对SAC-10沥青混合料的马歇尔试验,确定了该沥青混合料的矿料级配和最佳沥青含量。最后采用车辙试验、浸水马歇尔和冻融劈裂试验及小梁弯曲试验等一系列试验,检测超薄磨耗层沥青混合料的各项路用性能,为在实际工程中的应用提供理论依据。 相似文献