Urban university campus transportation and parking planning through a dynamic traffic simulation and assignment approach

Abstract

Many urban university campuses are considered major trip attractors. Considering the multimodal and complex nature of university campus transportation planning and operation, this paper proposes a dynamic traffic simulation and assignment analysis approach and demonstrates how such a methodology can be successfully applied. Central to the research is the estimation of trip origin–destinations and the calibration of a parking lot choice model. Dynamic simulation is utilized to simulate multiple modes of transportation within the transportation network while further assigning these modes with respect to various mode-specific roadway accessibilities. A multiple vehicle-class simulation analysis for planning purposes becomes a critical capability to predict how faculty and staff who once parked within the campus core choose other nearby alternate parking lots. The results highlight the effectiveness of the proposed approach in providing integrated and reliable solutions for challenging questions that face urban university campus planners and local transportation jurisdictions.     

A Framework for Developing Driving Cycles with On‐Road Driving Data

Abstract

This paper attempts to propose a framework on driving cycle development based on a thorough review of 101 transient driving cycles. A comparison of the driving cycles highlighted that Asian driving is the slowest but most aggressive while European driving is the fastest and smoothest. Further review of the cycle development methodologies identified three major elements for developing a driving cycle; test route selection, data collection and cycle construction methods. A framework was eventually proposed based on these findings and recommendations from this review. First, traffic activity patterns and quantitative statistics should be considered in determining the test routes. Speed data can be collected by using chase car method, on‐board measurement techniques or their hybrid. As for the construction of driving cycle, the matching approach has been more commonly used. It is recommended that the tendency of zero change in acceleration, which has been commonly ignored in the literature, and the application of succession probability at second‐by‐second level should be further explored. A fifth mode, creeping, is also recommended for modal analysis for characterizing urban congested driving conditions.     

Formal scientific research of traffic collision data utilizing GIS

This paper explores the tenuous link between speeding behavior and accident causation, one that has not been well established in the international literature to date. Taking advantage of established engineering conventions and formulae, we were able to set up an a priori hypothesis suitable for testing. Utilizing this formal scientific method (which GIS researchers have been criticised for not using) we establish a statistical link for this relationship. Our methodology can be used to support all police intervention strategies, including the controversial photo radar systems. The results from our research have been entered into a GIS in order to create a map for spatial display. This map illustrates the relative probability or risk of collision occurrence resulting from speeding at all intersections and interchanges within the scope of the study. It is suggested that this methodology could easily be maintained with periodic updates of data, thus creating a dynamic model from which to monitor traffic safety within the city. Furthermore, this model can be utilized to study specific strategies, allowing for the scrutiny of before, during and after effects. The study area is the entire city of Calgary, Alberta, Canada, and includes all traffic collisions occurring during the year of 1994.     

Development of a delay model for unsignalized intersections applicable to traffic assignment

Abstract

This paper develops a model for estimating unsignalized intersection delays which can be applied to traffic assignment (TA) models. Current unsignalized intersection delay models have been developed mostly for operational purposes, and demand detailed geometric data and complicated procedures to estimate delay. These difficulties result in unsignalized intersection delays being ignored or assumed as a constant in TA models.

Video and vehicle license plate number recognition methods are used to collect traffic volume data and to measure delays during peak and off-peak traffic periods at four unsignalized intersections in the city of Tehran, Iran. Data on geometric design elements are measured through field surveys. An empirical approach is used to develop a delay model as a function of influencing factors based on 5- and 15-min time intervals. The proposed model estimates delays on each approach based on total traffic volumes, rights-of-way of the subject approach and the intersection friction factor. The effect of conflicting traffic flows is considered implicitly by using the intersection friction factor. As a result, the developed delay model guarantees the convergence of TA solution methods.

A comparison between delay models performed using different time intervals shows that the coefficients of determination, R ², increases from 43.2% to 63.1% as the time interval increases from 5- to 15-min. The US Highway Capacity Manual (HCM) delay model (which is widely used in Iran) is validated using the field data and it is found that it overestimates delay, especially in the high delay ranges.     

A new approach to evaluating on-road public transport priority projects: balancing the demand for limited road-space

Despite widespread growth in on-road public transport priority schemes, road management authorities have few tools to evaluate the impacts of these schemes on all road users. This paper describes a methodology developed in Melbourne, Australia to assist the road management authority, VicRoads, evaluate trade-offs in the use of its limited road-space for new bus and tram priority projects. The approach employs traffic micro-simulation modelling to assess road-space re-allocation impacts, travel behaviour modelling to assess changes in travel patterns and a social cost benefit framework to evaluate impacts. The evaluation considers a comprehensive range of impacts including the environmental benefits of improved public transport services. Impacts on public transport reliability improvements are also considered. Although improved bus and tram reliability is a major rationale for traffic priority its use in previous evaluations is rare. The paper critiques previous approaches, describes the proposed method and explores some of the results found in its application. A major finding is that despite a more comprehensive approach to measuring the benefits of bus and tram priority, road-space reallocation is difficult to economically justify in road networks where public transport usage is low and car usage high. Strategies involving the balanced deployment of bus and tram priority measures where the allocation of time and space to PT minimises negative traffic impacts is shown to improve the overall management of road-space. A discussion of the approach is also provided including suggestions for further methodology development.

Locating inspection facilities in traffic networks: an artificial intelligence approach

Abstract

In order for traffic authorities to attempt to prevent drink driving, check truck weight limits, driver hours and service regulations, hazardous leaks from trucks, and vehicle equipment safety, we need to find answers to the following questions: (a) What should be the total number of inspection stations in the traffic network? and (b) Where should these facilities be located? This paper develops a model to determine the locations of uncapacitated inspection stations in a traffic network. We analyze two different model formulations: a single-objective optimization problem and a multi-objective optimization problem. The problems are solved by the Bee Colony Optimization (BCO) method. The BCO algorithm belongs to the class of stochastic swarm optimization methods, inspired by the foraging habits of bees in the natural environment. The BCO algorithm is able to obtain the optimal value of objective functions in all test problems. The CPU times required to find the best solutions by the BCO are found to be acceptable.     

A systematic review of route optimisation and pre-emption methods for emergency vehicles

ABSTRACT

Reducing the travel time of emergency vehicles (EVs) is an effective way to improve critical services such as ambulance, fire, and police. Route optimisation and pre-emption are powerful techniques used to reduce EV travel time. This paper presents a systematic literature review of optimisation and pre-emption techniques for routing EVs. A detailed classification of existing techniques is presented along with critical analysis and discussion. The study observes the limitations of existing routing systems and lack of real-world applications of the proposed pre-emption systems, leading to several interesting and important knowledge and implementation gaps that require further investigation. These gaps include optimisations using real-time dynamic traffic data, considering time to travel as a critical parameter within dynamic route planning algorithms, considering advanced algorithms, assessing and minimising the effects of EV routing on other traffic, and addressing safety concerns in traffic networks containing multiple EVs at the same time.     

Automatic ticketing on London underground

London Underground is currently going through a revolution in its fare collection systems. Magnetically encoded tickets are being introduced, obtainable from ticket office or self‐service machines, which are then checked automatically at start or finish of journey in the Underground's central zone. The microprocessor controlled equipment handles all accounting aspects of fare collection, because it is all part of a computer‐based network with centralized monitoring and control. The machinery was progressively installed from April 1987 to December 1988. This paper describes the history of the system, describes the new ticket and issuing machines, as well as discussing the development and project management tasks involved.     

Analysis of Work Zone Traffic Behavior for Planning Applications

Abstract

Understanding work zone traffic behavior is important for the planning and operation of work zones. The objective of this paper is to develop a mathematical model of work zone traffic flow elements by analyzing the relationships between speed, flow, and density that can be used to estimate the capacity of work zones. Traffic flow data were collected from 22 work zone sites on South Carolina interstate highways. The scatter plots of the collected data demonstrate that the relationship between speed and density does not follow Greenshields’ linear model. A non-linear hyperbolic model was developed to describe the relationship between speed and density. Using this model the capacity of a work zone was estimated to be 1550 passenger cars per hour for 2-lane to 1-lane closures. Adjustments to this capacity value to consider other types of vehicle as well as the work zone intensity are provided. Highway agencies can use this estimated capacity along with anticipated traffic demand to schedule work zone operations to avoid long periods of over-saturation.

The tapered approach to work zone lane closures used by South Carolina is similar to methods used in work zones throughout the world. The authors believe that the methodology described in this paper for modeling work zone traffic as well as estimating work zone capacity is transferable to other countries. The conversion of actual volumes to passenger car equivalents may have to be modified due to the significant differences in traffic makeup between the United States and other countries.     

Exploring the impact of connected and autonomous vehicles on freeway capacity using a revised Intelligent Driver Model

ABSTRACT

Connected and autonomous vehicle (CAV) technologies are expected to change driving/vehicle behavior on freeways. This study investigates the impact of CAVs on freeway capacity using a microsimulation tool. A four-lane basic freeway segment is selected as the case study through the Caltrans Performance Measurement System (PeMS). To obtain valid results, various driving behavior parameters are calibrated to the real traffic conditions for human-driven vehicles. In particular, the calibration is conducted using genetic algorithm. A revised Intelligent Driver Model (IDM) is developed and used as the car-following model for CAVs. The simulation is conducted on the basic freeway segment under different penetration rates of CAVs and different freeway speed limits. The results show that with an increase in the market penetration rate, freeway capacity increases, and will increase significantly as the speed limit increases.     

Applying measures of modelling quality to a national time series: a benchmark for transport demand models

ABSTRACT

In current urban planning practice, macroscopic transport demand and assignment models are essential for the evaluation of mid- and long-term land use developments and infrastructure investments. The credibility of their projections strongly depends on their ability to reproduce present day traffic volumes. Obviously, a simplified model of reality will display some shortcomings, and the effect of these is asserted by quality measures that quantify the divergence from observed traffic volumes. There is, however, only rough guidance regarding acceptable ranges of these measures. Most of the literature on this subject approach these ranges from below, by discussing measures attained by operational models and using these as a benchmark, or by using the adverse effects of modelling errors to derive a minimum quality level. On the contrary, this study suggests upper limits for quality measures by analysing year-on-year variations in traffic volumes that result from changing land use and infrastructure.     

Harmonizing heavy goods vehicle taxes in Europe: a British view

One of the biggest unresolved problems regarding the completion of the free internal transport market within the European community is the problem of harmonization of taxation on the road haulage industry. As the highest tax country, Britain might be expected to have to reduce its level of taxes as part of any harmonization.

This paper considers the current methodology of the British Department of Transport regarding the allocation of the track and external costs of road transport, in the light of developments in methodology and experience elsewhere in Western Europe and North America. We find a number of reasons for believing that, far from overstating the marginal social cost of use of roads by the road haulage industry, the current British approach actually understates it. Thus any move towards harmonizing tax levels may reduce taxes in Britain at a time when they should be increasing.     

Decision-making on Large Infrastructure Projects: The Role of the Dutch Parliament

Abstract

Validating microscopic traffic simulation models incorporates several challenges because of the inadequacy and rareness of validation data, and the complexity of the car following and lane-changing processes. In addition, validation data were usually measured in aggregate form at the link level and not at the level of the individual vehicle. The majority of model validation attempts in the literature use average link measurements of traffic characteristics. However, validation techniques based on averages of traffic variables have several limitations including possible inconsistency between the field observed and simulation-estimated variables, and as such the resulting spatial–temporal traffic stream patterns.

Due to these inconsistencies, this paper introduces a novel approach to the validation of microscopic traffic simulation models. A three-stage procedure for validating microscopic simulation models is presented. The paper describes the field measurements, experimental setup, and the simulation-based analysis of the three stages. The purpose of the first stage is to validate a benchmark simulator (NETSIM) using limited field data. The second stage examines the spatial–temporal traffic patterns extracted from the benchmark simulator versus those extracted from the simulation model to be validated (I-SIM-S). Different traffic patterns were examined accounting for various factors, such as traffic flow, link speeds, and signal timing. The third stage compares the aggregate traffic measures extracted from the subject simulator against those extracted from the benchmark simulator.     

Mobile phone use by young drivers: effects on traffic speed and headways

Abstract

This paper investigates the effects of mobile phone use while driving on traffic speed and headways, with particular focus on young drivers. For this purpose, a field survey was carried out in real road traffic conditions, in which drivers' speeds and headways were measured while using or not using a mobile phone. The survey took place within a University Campus area, allowing to distinguish between settings approximating to either free flow or interrupted flow conditions. Linear and loglinear regression methods were used to investigate the effects of mobile phone use and several other young driver characteristics, such as gender, driving experience and annual distance travelled, on vehicle speeds and headways. Separate models were developed for average free flow, interrupted flow, as well as for total average speed. Results show that mobile phone use leads to a statistically significant reduction in traffic speeds of young drivers in all types of traffic conditions. Furthermore, male and female drivers reduce their speed similarly when using a mobile phone while driving. However, male drivers using their mobile phone drive at lower speeds than female drivers not using their mobile phones. Sensitivity analysis revealed that, among all explanatory variables, the effect of mobile phone use on speed was most important. Accordingly, vehicle headways appear to increase for drivers using their mobile phone. However, this effect could not be statistically validated, due to the strong correlation between speed and headway.     

Capacity-constrained traffic forecasting model

Projecting future traffic is an important stage in any traffic and transportation planning study. Accurate traffic forecasting is vital for transportation planning, highway safety evaluation, traffic operations analysis, and geometric and pavement design among others. In view of its importance, this paper introduces a regression-based traffic forecasting methodology for a one dimensional capacity-constrained highway. Five different prediction functions are tested; the best was selected according to the accuracy of projections against historical traffic data. The three-parameter logistic function produced more accurate projections compared to other functions tested when highway capacity constraints were taken into consideration. The R ² values at various test locations ranged from 88% to 98%, indicating good prediction capability. Using the Fisher's information matrix approach, the t-statistic test showed all parameters in the logistic function were highly statistically significant. To evaluate reliability of projections, predictive intervals were calculated at a 95% level of confidence. Predictions using the logistic function were also compared to those predicted using the compound growth rate and linear regression methods. The results show that the proposed methodology generates much more reasonable projections than current practices.     

Extracting accurate location information from a highly inaccurate traffic accident dataset: A methodology based on a string matching technique

The objective of this research was to develop a model for validating traffic accident locations that would be applicable worldwide, regardless of linguistic or cultural differences. In order to achieve this, a Volunteered Geographic Information (VGI) dataset was used, the OpenStreetMap (OSM) project. To test the developed model, a total of 8550 accidents with fatal or non-fatal injuries that occurred in the City of Zagreb from 2010 to 2014 were evaluated. Traffic accident data was collected using the pen-and-paper method while the traffic accident locations were determined using Global Positioning System (GPS) receivers embedded within police vehicles. This form of data entry invariably introduces errors in both geometric and contextual attributes. To fully counteract these errors, the developed model consists of two key concepts: the Jaro–Winkler string matching technique and the Inverse Distance Weighting method. Over 66% of traffic accident locations were validated, which is an increase of 15% when compared to the classical approach. The model outlined in this paper shows a significant improvement in estimating the correct location of traffic accidents. This in turn results in a drastic decrease in resources needed to estimate the quality of accident locations.     

Managing Traffic by Privatization of Road Capacity: A Property Rights Approach

Abstract

Road congestion remains a serious problem, despite all the efforts to limit road use and to manage growing road traffic volumes. Economic approaches (such as pricing) are introduced based on traditional welfare economic theory. Although they are sometimes very successful, the magnitude of traffic issues also requires alternative and unconventional approaches. Perhaps a more innovative perspective is needed. The paper discusses an alternative economic approach starting from property rights theory. It is translated in transport systems in concepts of infrastructure capacity slot management, where slots are dynamically priced and exclusively allocated to individual users. Debates and practices regarding this approach in air traffic and rail traffic are further developed than in the field of road traffic. The paper aims to explore the potential benefits and disadvantages of the property rights approach for road traffic. Attention is paid to major institutional and technical conditions. The conclusion is that the approach theoretically has clear advantages and seems technologically feasible. Nevertheless, serious political and institutional issues have to be solved first.     

A model for the visualization and analysis of elevator traffic

ABSTRACT

Analysis of elevator traffic in high rise buildings is critical to the performance evaluation of elevator group control systems (EGCS). Elevator dispatching methods or parking algorithms in an EGCS can be designed or modified according to analyses of traffic flow. However, interpretation of traffic flow based solely on numerical data may not be explicit and transparent for EGCS experts as well as for other non-expert building administration. In this study, we present a model for visualization and analysis of elevator traffic. First, we present an alternative approach for traffic analysis which we call route visualization. In the proposed approach, we initially decompose elevator traffic into its component parts and investigate each component independently. Then, using superposition of components we obtain a reconstructed model of overall traffic. This modeling approach provides component-based traffic analysis and representation of routes with intensities through data visualization. In the second part we introduce a multi-dimensional analysis of time parameters in ECGS. This approach provides a comparative analysis of several control algorithms such as dispatch or park algorithms for different combinations of traffic components.     

Genetic algorithm-based simulation optimization of the ALINEA ramp metering system: a case study in Atlanta

ABSTRACT

This paper presents a case study of the optimal ALINEA ramp metering system model of a corridor of the metro Atlanta freeway. Based on real-world traffic data, this study estimates the origin-destination matrix for the corridor. Using a stochastic simulation-based optimization framework that combines a micro-simulation model and a genetic algorithm-based optimization module, we determine the optimal parameter values of a combined ALINEA ramp metering system with a queue flush system that minimizes total vehicle travel time. We found that the performance of ramp metering with optimized parameters, which is very sensitive possibly because bottlenecks are correlated, outperforms the no control model with its optimized parameters in terms of reducing total travel time.