Effects of the 80 km/h and variable speed limits on air pollution in the metropolitan area of barcelona

In 2008 the regional government of Catalonia (Spain) reduced the maximum speed limit on several stretches of congested urban motorway in the Barcelona metropolitan area to 80 km/h, while in 2009 it introduced a variable speed system on other stretches of its metropolitan motorways. We use the differences-in-differences method, which enables a policy impact to be measured under specific conditions, to assess the impact of these policies on emissions of NO_x and PM₁₀. Empirical estimation indicate that reducing the speed limit to 80 km/h causes a 1.7–3.2% increase in NO_x and 5.3–5.9% in PM₁₀. By contrast, the variable speed policy reduced NO_x and PM₁₀ pollution by 7.7–17.1% and 14.5–17.3%. As such, a variable speed policy appears to be a more effective environmental policy than reducing the speed limit to a maximum of 80 km/h.     

Estimation of nitrogen oxides emissions from petrol and diesel passenger cars by means of on-board monitoring: Effect of vehicle speed,vehicle technology,engine type on emission rates

NO_X emission rates of 13 petrol and 3 diesel passenger cars as a function of average speed from 10 to 120 km/h, emission class (pre-Euro 1 – Euro 5), engine type were investigated by on-board monitoring on roads and highways of St. Petersburg using a portative Testo XXL 300 gas analyzer. The highest level of NO_X emission 0.5–2.5 g/km was inherent to old pre-Euro 1 petrol cars without a catalytic converter. NO_X emissions rates of Euro 1 and Euro 2 petrol cars changed within 0.15–0.9 g/km, Euro 3 – 0.015–0.27 g/km, Euro 4 – 0.013–0.1 g/km, Euro 5 – 0.002–0.043 g/km. Euro 3 – Euro 4 petrol cars generally satisfied corresponding NO_X Emission Standards (ES), except cold-start period, Euro 5 petrol cars did not exceed ES. Warmed, stabilized engines of Euro 3 – Euro 5 petrol cars showed 5–10 times lower NO_X emission rates than corresponding ES in the range of speed from 20 to 90 km/h. NO_X emission rates of diesel Euro 3 and Euro 4 cars varied from 0.45 to 1.1 g/km and from 0.31 to 1.1 g/km, respectively. Two examined diesel Euro 3 and one Euro 4 passenger vehicles did not satisfy NO_X ES at real use. Euro 3 diesel cars showed 28.9 times higher NO_X emissions than Euro 3 petrol cars and Euro 4 diesel car demonstrated 17.6 times higher NO_X emissions than Euro 4 petrol cars at warmed and stabilized engine at a cruise speed ranging from 30 to 60 km/h.     

Effects of low speed limits on freeway traffic flow

Recent years have seen a renewed interest in Variable Speed Limit (VSL) strategies. New opportunities for VSL as a freeway metering mechanism or a homogenization scheme to reduce speed differences and lane changing maneuvers are being explored. This paper examines both the macroscopic and microscopic effects of different speed limits on a traffic stream, especially when adopting low speed limits. To that end, data from a VSL experiment carried out on a freeway in Spain are used. Data include vehicle counts, speeds and occupancy per lane, as well as lane changing rates for three days, each with a different fixed speed limit (80 km/h, 60 km/h, and 40 km/h). Results reveal some of the mechanisms through which VSL affects traffic performance, specifically the flow and speed distribution across lanes, as well as the ensuing lane changing maneuvers. It is confirmed that the lower the speed limit, the higher the occupancy to achieve a given flow. This result has been observed even for relatively high flows and low speed limits. For instance, a stable flow of 1942 veh/h/lane has been measured with the 40 km/h speed limit in force. The corresponding occupancy was 33%, doubling the typical occupancy for this flow in the absence of speed limits. This means that VSL strategies aiming to restrict the mainline flow on a freeway by using low speed limits will need to be applied carefully, avoiding conditions as the ones presented here, where speed limits have a reduced ability to limit flows. On the other hand, VSL strategies trying to get the most from the increased vehicle storage capacity of freeways under low speed limits might be rather promising. Additionally, results show that lower speed limits increase the speed differences across lanes for moderate demands. This, in turn, also increases the lane changing rate. This means that VSL strategies aiming to homogenize traffic and reduce lane changing activity might not be successful when adopting such low speed limits. In contrast, lower speed limits widen the range of flows under uniform lane flow distributions, so that, even for moderate to low demands, the under-utilization of any lane is avoided. These findings are useful for the development of better traffic models that are able to emulate these effects. Moreover, they are crucial for the implementation and assessment of VSL strategies and other traffic control algorithms.     

Airlines’ reaction to high-speed rail entries: Empirical study of the Northeast Asian market

We investigate the impact of the commencement of high-speed rail (HSR) services on airlines’ domestic available seats on affected routes in China, Japan, and South Korea. The study is based on a dataset covering the 1994–2012 period. We use the propensity score matching method to pair HSR affected routes with routes without HSR services. The difference-in-difference approach is used to estimate the impact of HSR entry. We find that HSR entries may, on average, lead to a more significant drop in airlines’ seat capacity in China than in Japan and Korea given similar HSR service speed. In China, HSR services with a maximum speed about 200 km/h can produce strong negative impacts on medium-haul air routes but induce more air seat capacity on long-haul routes. HSR services with a maximum speed of 300 km/h have little extra impact on medium-haul routes but a strong negative impact on long-haul routes. Finally, although HSR has a strong negative impact in Japan’s short-haul and medium-haul air markets, little impact is observed in its long-haul markets.     

Ultrafine particle infiltration into passenger vehicles. Part II: Model analysis

Experimental studies showed that infiltration and passive ventilation are important air exchange mechanisms inside vehicles but previous mathematical models did not consider either one. In this study, we incorporated infiltration and passive ventilation to advance the existing mathematical models and evaluated how different transport mechanisms affect passenger exposures at increasing speeds. Infiltration was formulated using Bernoulli’s equation and passive ventilation was derived empirically. The new model describes ultrafine particle (UFP) and carbon dioxide (CO₂) transport for a wide range of driving speed under any ventilation conditions. Unlike statistical models, this mathematical model can also provide vehicle-specific and transport mechanism-specific information. The model predictions were in a good agreement with data collected from 10 different vehicle models with an average discrepancy of less than 16% for UFPs and less than 3% for CO₂. Under outdoor air (OA) mode, when the fan is off, the model simulation showed that the infiltration and passive ventilation can substantially increase the UFP I/O (in-cabin/on-road concentrations) ratio from 0.15 at 0 km/h to 0.57 at 130 km/h. At medium fan setting, mechanical ventilation dominates and UFP I/O stays at 0.58 regardless of driving speed. Under recirculation (RC) mode, infiltration increases and the RC-mode filtration only removed 44% and 69% of the infiltrated particles at the lowest and medium fan settings, respectively. Model simulations under OA mode show that infiltration starts to occur above 115 km/h with the lowest fan setting; whereas, medium and higher fan settings prevent infiltration up to 145 km/h.     

Going fast or going green? Evidence from environmental speed limits in Norway

This paper studies the impact of speed limits on local air pollution using a series of date-specific speed limit reductions in Oslo over the 2004–2011 period. We find that lowering the speed limit from 80 to 60 km/h reduces travel speed by 5.8 km/h. However, we find no evidence of reduced air pollution as measured next to the treated roads. Our estimates suggest an annual time loss of the speed limit reductions of 66 USD per affected vehicle. Our findings imply that policy makers need to consider other actions than speed limit reductions to improve local air quality.     

Nationwide survey on the posting of minimum speed limit signs on Interstate freeways

This paper presents the results of the mail out survey conducted in the United States to unveil the current state of practice related to the posting of minimum speed limit signs on Interstate freeway system. The analysis of the survey results has revealed that half of the country (25 states) posts the minimum speed limit on Interstate freeways. The most common posting is 40 mph. There are few states that post 45 mph and 55 mph in some sections on Interstate freeways. The survey results has also discovered that many states raised the maximum speed limits on Interstate freeways as the consequence of the National Highway System (NHS) designation Act of 1995 without revising or studying the effect of the existing minimum speed limits on traffic operation. Implications for future research relates to a multi state study which will evaluate the relevance of minimum speed limits on speed variability that is created by the posting of minimum speed limit.     

A forecast air pollution model applied to a hypothetical urban road pricing scheme: An empirical study in Madrid

Reducing the air pollution from increases in traffic congestion in large cities and their surroundings is an important problem that requires changes in travel behavior. Road pricing is an effective tool for reducing air pollution, as reflected currently urban road pricing outcomes (Singapore, London, Stockholm and Milan). A survey was conducted based on establishing a hypothetical urban road pricing system in Madrid (a random sample size n = 1298). We developed a forecast air pollution model with time series analysis to evaluate the consequences of possible air pollution decreases in Madrid. Results reveal that the hypothetical road pricing for Madrid could have highly significant effects on decreasing air pollution outside of the city and in the inner city during the peak operating time periods of maximum congestion (morning peak hours from 7:00 to 10:00 and evening peak hours from 18:00 to 20:00). Furthermore, this system could have significant positive effects on a shift toward using public transport and non-motorized modes inside the hypothetical toll zone. This reveals that the system has a high capacity to motivate a decrease in air pollution and impose more sustainable behavior for public transport users.     

Regional climate impact of aerosols emitted by transportation modes and potential effects of policies on demand and emissions

The transportation system is one of the main sectors with significant climate impact. In the U.S. it is the second main emitter of carbon dioxide. Its impact in terms of emission of carbon dioxide is well recognized. But a number of aerosol species have a non-negligible impact. The radiative forcing due to these species needs to be quantified. A radiative transfer code is used. Remote sensing data is retrieved to characterize different regions. The radiative forcing efficiency for black carbon are 396 ± 200 W/m²/AOD for the ground mode and 531 ± 190 W/m²/AOD for the air transportation, under clear sky conditions. The radiative forcing due to contrail is 0.14 ± 0.06 W/m² per percent coverage. Based on the forcing from the different species emitted by each mode of transportation, policies may be envisioned. These policies may affect demand and emissions of different modes of transportation. Demand and fleet models are used to quantify these interdependencies. Depending on the fuel price of each mode, mode shifts and overall demand reduction occur, and more fuel efficient vehicles are introduced in the fleet at a faster rate. With the introduction of more fuel efficient vehicles, the effect of fuel price on demand is attenuated. An increase in fuel price of 50 cents per gallon, scaled based on the radiative forcing of each mode, results in up to 5% reduction in emissions and 6% reduction in radiative forcing. With technologies, significant reduction in climate impact may be achieved.     

How wide should be the adjacent area to an urban motorway to prevent potential health impacts from traffic emissions?

In recent years, several studies show that people who live, work or attend school near the main roadways have an increased incidence and severity of health problems that may be related with traffic emissions of air pollutants. The concentrations of near-road atmospheric pollutants vary depending on traffic patterns, environmental conditions, topography and the presence of roadside structures. In this study, the vertical and horizontal variation of nitrogen dioxide (NO₂) and benzene (C₆H₆) concentration along a major city ring motorway were analysed. The main goal of this study is to try to establish a distance from this urban motorway considered “safe” concerning the air pollutants human heath limit values and to study the influence of the different forcing factors of the near road air pollutants transport and dispersion. Statistic significant differences (p = 0.001, Kruskal–Wallis test) were observed between sub-domains for NO₂ representing different conditions of traffic emission and pollutants dispersion, but not for C₆H₆ (p = 0.335). Results also suggest significant lower concentrations recorded at 100 m away from roadway than at the roadside for all campaigns (p < 0.016 (NO₂) and p < 0.036 (C₆H₆), Mann–Whitney test). In order to have a “safe” life in homes located near motorways, the outdoor concentrations of NO₂ must not exceed 44–60.0 μg m⁻³ and C₆H₆ must not exceed 1.4–3.3 μg m⁻³. However, at 100 m away from roadway, 81.8% of NO₂ receptors exceed the annual limit value of human health protection (40 μg m⁻³) and at the roadside this value goes up to 95.5%. These findings suggest that the safe distance to an urban motorway roadside should be more at least 100 m. This distance should be further studied before being used as a reference to develop articulated urban mobility and planning policies.     

Development of a corrected average speed model for calculating carbon dioxide emissions per link unit on urban roads

The purpose of our study is to develop a “corrected average emission model,” i.e., an improved average speed model that accurately calculates CO₂ emissions on the road. When emissions from the central roads of a city are calculated, the existing average speed model only reflects the driving behavior of a vehicle that accelerates and decelerates due to signals and traffic. Therefore, we verified the accuracy of the average speed model, analyzed the causes of errors based on the instantaneous model utilizing second-by-second data from driving in a city center, and then developed a corrected model that can improve the accuracy. We collected GPS data from probe vehicles, and calculated and analyzed the average emissions and instantaneous emissions per link unit. Our results showed that the average speed model underestimated CO₂ emissions with an increase in acceleration and idle time for a speed range of 20 km/h and below, which is the speed range for traffic congestion. Based on these results, we analyzed the relationship between average emissions and instantaneous emissions according to the average speed per link unit, and we developed a model that performed better with an improved accuracy of calculated CO₂ emissions for 20 km/h and below.     

The cost of convenience; Air pollution and noise on freeway and arterial light rail station platforms in Los Angeles

Light rail transit (LRT) systems constitute one of the most sustainable public transportation modes and transit agencies have increasingly constructed LRT lines along the median of roadways to reduce land acquisition costs and traffic conflicts. Despite these conveniences, few studies have examined the air pollution and noise exposures for passengers on LRT station platforms within freeway or arterial medians. In response, we monitored particle number count (PNC) concentrations and noise levels on 17 station platforms in the Los Angeles metro system in summer 2012 and assessed differences between freeway and arterial platforms. We visited each station on average 7 times for approximately 19 min with two teams carrying a full set of instruments. As expected, impacts were higher on green line platforms in the center of a grade-separated freeway compared to blue line platforms in the center of an arterial due to being in close proximity to greater traffic volumes. Overall, freeway-arterial platform differences were 35,100 versus 20,000 particles/cm³ for PNC and 83 versus 62 dBA for noise. This average noise intensity on green line platforms was four times that on blue line stations. We also found that PNC concentrations were significantly higher at open air monitoring platform positions compared to standing under a shade canopy (about 2000 particles/cm³ higher), but that noise levels were significantly lower at open air positions compared to under canopy positions (about 3.2 dBA lower). Results identify important factors for transport planners to consider when locating and designing in-roadway LRT platforms.     

Comparative analysis of the energy consumption and CO2 emissions of 40 electric,plug-in hybrid electric,hybrid electric and internal combustion engine vehicles

This paper analyses the results of the Royal Automobile Clubhallo’s 2011 RAC Future Car Challenge, an annual motoring challenge in which participants seek to consume the least energy possible while driving a 92 km route from Brighton to London in the UK. The results reveal that the vehicle’s power train type has the largest impact on energy consumption and emissions. The traction ratio, defined as the fraction of time spent on the accelerator in relation to the driving time, and the amount of regenerative braking have a significant effect on the individual energy consumption of vehicles. In contrast, the average speed does not have a great effect on a vehicles’ energy consumption in the range 25–70 km/h.     

Effects of e-bikes on bicycle use and mode share

In Norway, as in many countries, a political goal is to increase bicycle use, and the e-bike is promising in this respect. However, concerns have been raised about mode-share effects. It has been argued that if the e-bike’s only function is in cycling becoming cycling with electric assistance, there would be no benefit to either the environment or public health. Little is yet known about the use of the e-bike, or of its potential in reducing motorized travel. In the current study, 66 randomly selected participants were given an e-bike to use for a limited period of time and the results compared with those of a control group (N = 160). E-bike cycling trips increased from 0.9 to 1.4 per day, distance from 4.8 km to 10.3 km and, as a share of all transport, from 28% to 48%, whereas with the control group there was no increase in cycling. The effect of the e-bike increased with time, indicating a learning effect among users, and was greater for female than for male cyclists. There were no differences with age. Overall, the results suggest that the e-bike is indeed practical for everyday travel.     

Experimental evaluation of the efficiency of trenches for the mitigation of train-induced vibrations

In this work, the efficiency of absorbing barriers for the mitigation of ground vibrations induced by railway traffic has been evaluated by means of two different experimental campaigns conducted in situ, along the newly-built, high-speed railway line that connects the Italian cities of Milan and Bologna. In the first stage of testing, a series of ideal barriers created from unsupported empty trenches were tested to assess the effects of barrier depth on their efficiency in reducing vertical ground accelerations. The second stage of testing was performed to investigate the efficiency of a full-scale prototype barrier, made of a 2-meter-deep trench supported by two precast reinforced concrete plates connected by steel bars, during transit of an ETR 500 train at a speed of 120 km/h.     

China’s electric car frustrations

By 2020, the vehicle population in China will likely exceed 280 million—exacerbating national energy security, urban air pollution, and traffic congestion. In response, many local and regional governments in China are pursuing an expanding array of measures to restrain growth in personal vehicle ownership and, along with the central government, reducing emissions and energy use of vehicles. One prominent strategy is the promotion of new energy vehicles, especially plug-in electric vehicles (PEVs). Large subsidies were offered—up to $27,600 (171,000 RMB) per vehicle in some regions, including almost $9200 (57,000 RMB) from the central government—which suggests that China is making a major commitment to PEVs. But sales have been meager. In 2013, only 17,600 PEVs, mostly buses and utility trucks, were sold, less than 0.1% of total civilian vehicle sales. Several factors explain the failure of PEV sales to take off: (1) protectionism by local governments; (2) uncertainty over which electric-drive vehicle technologies to promote and what consumers are willing to pay, (3) lagging investments in charging infrastructure, and (4) conservative investment behavior by automakers and battery manufacturers. The central government issued directives to local governments in late 2013 to reduce barriers to out-of-town companies, resulting in modest sales increases in early 2014, but a more coherent, broader, and effective set of policies, incentives, and strategies are needed to overcome consumer and industry resistance and the lack of charging infrastructure.     

Population exposure to ultrafine particles: Size-resolved and real-time models for highways

Prior research on ultrafine particles (UFP) emphasizes that concentrations are especially high on-highway, and that time on highways contribute disproportionately to total daily exposures. This study estimates individual and population exposure to ultra-fine particles in the Minneapolis – St. Paul (Twin Cities) metropolitan area, Minnesota. Our approach combines a real-time model of on-highway size-resolved UFP concentrations (32 bins, 5.5–600 nm); individual travel patterns, derived from GPS travel trajectories collected in 144 individual vehicles (123 h at locations with UFP estimates among 624 vehicle-hours of travel); and, loop-detector data, indicating real-time traffic conditions throughout the study area. The results provide size-resolved spatial and temporal patterns of exposure to UFP among freeway users. On-highway exposures demonstrate significant variability among users, with highest concentrations during commuting peaks and near highway interchanges. Findings from this paper could inform future epidemiological studies in on-road exposure to UFP by linking personal exposures to traffic conditions.     

Thermodynamic,environmental and economic effects of diesel and biodiesel fuels on exhaust emissions and nano-particles of a diesel engine

In this study, diesel (JIS#2) and various biodiesel fuels (BDF20, BDF50, BDF100) are used to operate the diesel engine at 100 Nm, 200 Nm and full load; while the engine speed is 1800 rpm. The system is experimentally studied, and the energy, exergy, sustainability, thermoeconomic and exergoeconomic analyses are performed to the system. The Engine Exhaust Particle Sizer is used to measure the size distribution of engine exhaust particle emissions. Also, the data of the exhaust emissions, soot, particle numbers, fuel consumptions, etc. are measured. It is found that (i) most of the exhaust emissions (except NO_x) are directly proportional to the engine load, (ii) maximum CO₂ and NO_x emissions rates are generally determined for the BDF100 biodiesel fuel; while the minimum ones are calculated for the JIS#2 diesel fuel. On the other hand, the maximum CO and HC emissions rates are generally computed for the JIS#2 diesel fuel; while the minimum ones are found for the BDF100 biodiesel fuel, (iii) fuel consumptions from maximum to minimum are BDF100 > BDF50 > BDF20 > JIS#2 at all of the engine loads, (iv) particle concentration of the JIS#2 diesel fuel is higher than the biodiesel fuels, (v) soot concentrations of the JIS#2, BDF20 and BDF50 fuels are directly proportional to the engine load; while the BDF100 is inversely proportional, (vi) system has better energy and exergy efficiency when the engine is operated with the biodiesel fuels (vii) sustainability of the fuels are BDF100 > BDF50 > BDF20 > JIS#2, (viii) thermoeconomic and exergoeconomic parameters rates from maximum to minimum are JIS#2 > BDF20 > BDF50 > BDF100.     

On the electrification of road transportation – A review of the environmental,economic, and social performance of electric two-wheelers

Electrification is widely considered as a viable strategy for reducing the oil dependency and environmental impacts of road transportation. In pursuit of this strategy, most attention has been paid to electric cars. However, substantial, yet untapped, potentials could be realized in urban areas through the large-scale introduction of electric two-wheelers. Here, we review the environmental, economic, and social performance of electric two-wheelers, demonstrating that these are generally more energy efficient and less polluting than conventionally-powered motor vehicles. Electric two-wheelers tend to decrease exposure to pollution as their environmental impacts largely result from vehicle production and electricity generation outside of urban areas. Our analysis suggests that the price of e-bikes has been decreasing at a learning rate of 8%. Despite price differentials of 5000 ± 1800 EUR₂₀₁₂ kW h⁻¹ in Europe, e-bikes are penetrating the market because they appear to offer an apparent additional use value relative to bicycles. Mid-size and large electric two-wheelers do not offer such an additional use value compared to their conventional counterparts and constitute niche products at price differentials of 700 ± 360 EUR₂₀₁₂ kW⁻¹ and 160 ± 90 EUR₂₀₁₂ kW⁻¹, respectively. The large-scale adoption of electric two-wheelers can reduce traffic noise and road congestion but may necessitate adaptations of urban infrastructure and safety regulations. A case-specific assessment as part of an integrated urban mobility planning that accounts, e.g., for the local electricity mix, infrastructure characteristics, and mode-shift behavior, should be conducted before drawing conclusions about the sustainability impacts of electric two-wheelers.