Estimation of road traffic noise emissions: The influence of speed and acceleration

This paper relies on vehicle trajectory collection on a corridor, to compare different traffic representations used for the estimation of the sound power of light vehicles and the resulting sound pressure levels. Four noise emission models are tested. The error introduced when the emissions are calculated based on speeds measured at regular intervals along the road network are quantified and explained. The current noise emission models might in particular misestimate noise levels under congestion. This bias can be reduced by introducing additional traffic variables in the modeling. In addition, significant differences within the models are highlighted, especially concerning their accounting of vehicle accelerations. Models that rely on a binary representation of acceleration regimes (a vehicle or a road segment is accelerating or not) can lead to errors in practice. Models under use in Europe have a very low sensitivity to acceleration values. These results help underlying the further required improvements of dynamic road traffic noise models.     

Modelling acceleration decisions in traffic streams with weak lane discipline: A latent leader approach

Acceleration is an important driving manoeuvre that has been modelled for decades as a critical element of the microscopic traffic simulation tools. The state-of-the art acceleration models have however primarily focused on lane based traffic. In lane based traffic, every driver has a single distinct lead vehicle in the front and the acceleration of the driver is typically modelled as a function of the relative speed, position and/or type of the corresponding leader. On the contrary, in a traffic stream with weak lane discipline, the subject driver may have multiple vehicles in the front. The subject driver is therefore subjected to multiple sources of stimulus for acceleration and reacts to the stimulus from the governing leader. However, only the applied accelerations are observed in the trajectory data, and the governing leader is unobserved or latent. The state-of-the-art models therefore cannot be directly applied to traffic streams with weak lane discipline.This prompts the current research where we present a latent leader acceleration model. The model has two components: a random utility based dynamic class membership model (latent leader component) and a class-specific acceleration model (acceleration component). The parameters of the model have been calibrated using detailed trajectory data collected from Dhaka, Bangladesh. Results indicate that the probability of a given front vehicle of being the governing leader can depend on the type of the lead vehicle and the extent of lateral overlap with the subject driver. The estimation results are compared against a simpler acceleration model (where the leader is determined deterministically) and a significant improvement in the goodness-of-fit is observed. The proposed models, when implemented in microscopic traffic simulation tools, are expected to result more realistic representation of traffic streams with weak lane discipline.     

Spin glass and the interactions of congestion and emissions: An exploratory step

This paper models traffic congestion formation on highways and roads by recognizing the centrality of dynamical systems and using concepts from complexity theory as imbedded in the spin glasses analogue. Further, it explores the concept of how an increase in air pollution caused by vehicle exhaust emission can be traced to traffic congestion, specifically to the acceleration/deceleration of vehicles on the roads. First, spin glass is introduced and then by applying the two-dimensional x − y Ising model and defining a Hamiltonian (based on Edwards-Anderson and Mattis models of spin glass systems) for a system of vehicles on the road, derivations are made of the specific friction of congestion and the bulk modulus of congestion using the Gibbs-Boltzmann statistic. Similarly using the interactions of vehicles with each other and the resulting accelerations and decelerations of vehicles as the basis for exhaust emissions, derivations are made of a specificity of exhaust emissions. These are analogues to the entropy models of thermodynamics. This series of derivations serves as an analytical model for detecting incidents of congestion and increase in air pollution due to exhaust emissions in transportation systems.     

Network-wide traffic and environmental impacts of acceleration and deceleration among Eco-Driving Vehicles in different road configurations

Eco-Driving, a driver behaviour-based method, has featured in a number of national policy documents as part of CO₂ emission reduction or climate change strategies. This investigation comprises a detailed assessment of acceleration and deceleration in Eco-Driving Vehicles at different penetration levels in the vehicle fleet, under varying traffic composition and volume. The impacts of Eco-Driving on network-wide traffic and environmental performance at a number of speed-restricted road networks (30?km/h) is quantified using microsimulation. The results show that increasing levels of Eco-Driving in certain road networks result in significant environmental and traffic congestion detriments at the road network level in the presence of heavy traffic. Increases in CO₂ emissions of up to 18% were found. However, with the addition of vehicle-to-vehicle or vehicle-to-infrastructure communication technology which facilitates dynamic driving control on speed and acceleration/deceleration in vehicles, improvements in CO₂ emissions and traffic congestion are possible using Eco-Driving.     

Reducing emissions at land border crossings through queue reduction and expedited security processing

Vehicle border crossings between Mexico and the United States generate significant amounts of air pollution, which can pose health threats to personnel at the ports of entry (POEs) as well as drivers, pedestrians, and local inhabitants. Although these health risks could be substantial, there is little previous work quantifying detailed emission profiles at POEs. Using the Mariposa POE in Nogales, Arizona as a case study, light-duty and heavy-duty vehicle emissions were analyzed with the objective of identifying effective emission reduction strategies such as inspection streamlining, physical infrastructure improvements, and fuel switching. Historical traffic information as well as field data were used to establish a simulation model of vehicle movement in VISSIM. Four simulation scenarios with varied congestion levels were considered to represent real-world seasonal changes in traffic volume. Four additional simulations captured varying levels of expedited processing procedures. The VISSIM output was analyzed using the EPA’s MOVES emission simulation software for conventional air pollutants. For the highest congestion scenario, which includes a 200% increase in vehicle volume, total emissions increase by around 460% for PM_2.5 and NO_x, and 540% for CO, SO₂, GHGs, and NMHC over uncongested conditions for a two-hour period. Expedited processing and queue reduction can reduce emissions in this highest congestion scenario by as much as 16% for PM_2.5, 18% for NO_x, 20% for NMHC, 7% for SO₂ and 15% for GHGs and CO. Other potential mitigation strategies examined include fleet upgrades, fuel switching, and fuel upgrades. Adoption of some or all of these changes would not only reduce emissions at the Mariposa POE, but would have air-quality benefits for nearby populations in both the US and Mexico. Fleet-level changes could have far-reaching improvements in air quality on both sides of the border.     

Analysis of telecommuting behavior and impacts on travel demand and the environment

The discussion of whether, and to what extent, telecommuting can curb congestion in urban areas has spanned more than three decades. This study develops an integrated framework to provide the empirical evidence of the potential impacts of home-based telecommuting on travel behavior, network congestion, and air quality. In the first step, we estimate a telecommuting adoption model using a zero-inflated hierarchical ordered probit model to determine the factors associated with workers’ propensity to adopt telecommuting. Second, we implement the estimated model in the POLARIS activity-based framework to simulate the potential changes in workers’ activity-travel patterns and network congestion. Third, the MOVES mobile source emission simulator and Autonomie vehicle energy simulator are used to estimate the potential changes in vehicular emissions and fuel use in the network as a result of this policy. Different policy adoption scenarios are then tested in the proposed integrated platform. We found that compared to the current baseline situation where almost 12% of workers in Chicago region have flexible working time schedule, in the case when 50% of workers have flexible working time, telecommuting can reduce total daily vehicle miles traveled (VMT) and vehicle hours traveled (VHT) up to 0.69% and 2.09%, respectively. Considering the same comparison settings, this policy has the potential to reduce greenhouse gas and particulate matter emissions by up to 0.71% and 1.14%, respectively. In summary, our results endorse the fact that telecommuting policy has the potential to reduce network congestion and vehicular emissions specifically during rush hours.     

A field evaluation case study of the environmental and energy impacts of traffic calming

This study quantifies the energy and environmental impact of a selection of traffic calming measures using a combination of second-by-second floating-car global positioning system data and microscopic energy and emission models. It finds that traffic calming may result in negative impacts on vehicle fuel consumption and emission rates if drivers exert aggressive acceleration levels to speed up to their journeys. Consequently by eliminating sharp acceleration maneuvers significant savings in vehicle fuel consumption and emission rates are achievable through driver education. The study also demonstrates that high emitting vehicles produce CO emissions that are up to 25 times higher than normal vehicle emission levels while low emitting vehicles produce emissions that are 15–35% of normal vehicles. The relative increases in vehicle fuel consumption and emission levels associated with the sample traffic calming measures are consistent and similar for normal, low, and high emitting vehicles.     

Estimating fuel consumption and emissions based on reconstructed vehicle trajectories

Microscopic emission models are widely used in emission estimation and environment evaluation. Traditionally, microscopic traffic simulation models and probe vehicles are two sources of inputs to a microscopic emission model. However, they are not effective in reflecting all vehicles' real‐world operating conditions. Using each vehicle's spot speed data recorded by detectors, this paper provides a new method to estimate all vehicles' real‐world activities data. These data can then be used as inputs to a microscopic emission model to estimate vehicle fuel consumption and emissions. The main task is to reconstruct trajectory of each vehicle and calculate second‐by‐second speed and acceleration from the activities data. The Next Generation Simulation dataset and the Comprehensive Modal Emissions Model are used in this study to calculate and analyze the emission results for both lane‐level and link‐level. The results showed that using the proposed method for estimating vehicle fuel consumption and emissions is promising. Copyright © 2012 John Wiley & Sons, Ltd.     

Evaluating the impacts of urban corridor traffic signal optimization on vehicle emissions and fuel consumption

This study investigates the impacts of traffic signal timing optimization on vehicular fuel consumption and emissions at an urban corridor. The traffic signal optimization approach proposed integrates a TRANSIMS microscopic traffic simulator, the VT-Micro model (a microscopic emission and fuel consumption estimation model), and a genetic algorithm (GA)-based optimizer. An urban corridor consisting of four signalized intersections in Charlottesville, VA, USA, is used for a case study. The result of the case study is then compared with the best traffic signal timing plan generated by Synchro using the TRANSIMS microscopic traffic simulator. The proposed approach achieves much better performance than that of the best Synchro solution in terms of air quality, energy and mobility measures: 20% less network-wide fuel consumption, 8–20% less vehicle emissions, and nearly 27% less vehicle-hours-traveled (VHT).     

Development of simulated driving cycles for light,medium, and heavy duty trucks: Case of the Toronto Waterfront Area

Driving cycles are an important input for state-of-the-art vehicle emission models. Development of a driving cycle requires second-by-second vehicle speed for a representative set of vehicles. Current standard driving cycles cannot reflect or forecast changes in traffic conditions. This paper introduces a method to develop representative driving cycles using simulated data from a calibrated microscopic traffic simulation model of the Toronto Waterfront Area. The simulation model is calibrated to reflect road counts, link speeds, and accelerations using a multi-objective genetic algorithm. The simulation is validated by comparing simulated vs. observed passenger freeway cycles. The simulation method is applied to develop AM peak hour driving cycles for light, medium and heavy duty trucks. The demonstration reveals differences in speed, acceleration, and driver aggressiveness between driving cycles for different vehicle types. These driving cycles are compared against a range of available driving cycles, showing different traffic conditions and driving behaviors, and suggesting a need for city-specific driving cycles. Emissions from the simulated driving cycles are also compared with EPA’s Heavy Duty Urban Dynamometer Driving Schedule showing higher emission factors for the Toronto Waterfront cycles.     

Weather and road geometry impact on longitudinal driving behavior: Exploratory analysis using an empirically supported acceleration modeling framework

The objective of this paper is to quantify and characterize driver behavior under different roadway geometries and weather conditions. In order to explore how a driver perceives the rapidly changing driving surrounding (i.e. different weather conditions and road geometry configurations) and executes acceleration maneuvers accordingly, this paper extends a Prospect Theory based acceleration modeling framework. A driving simulator is utilized to conduct 76 driving experiments. Foggy weather, icy and wet roadway surfaces, horizontal and vertical curves, and different lane and shoulder widths are simulated while having participants driving behind a yellow cab at speeds/headways of their choice. After studying the driving trends observed in the different driving experiments, the extended Prospect Theory based acceleration model is calibrated using the produced trajectory data. The extended Prospect Theory based model parameters are able to reflect a change in risk-perception and acceleration maneuvering when receiving different parameterized exogenous information. The results indicate that drivers invest more attention and effort to deal with the roadway challenges compared to the effort to deal with the weather conditions. Moreover, the calibrated model is used to simulate a highway segment and observe the produced fundamental diagram. The preliminary results suggest that the model is capable of capturing driver behavior under different roadway and weather conditions leading to changes in capacity and traffic disruptions.     

Traffic and emissions impact of congestion charging in the central Beijing urban area: A simulation analysis

Congestion charging is being considered as a potential measure to address the issue of substantially increased traffic congestion and vehicle emissions in Beijing. This study assessed the impact of congestion charging on traffic and emissions in Beijing using macroscopic traffic simulation and vehicle emissions calculation. Multiple testing scenarios were developed with assumptions in different charging zone sizes, public transit service levels and charging methods. Our analysis results showed that congestion charging in Beijing may increase public transit use by approximately 13%, potentially reduce CO and HC emissions by 60–70%, and reduce NOx emissions by 35–45% within the charging zone. However, congestion charging may also result in increased travel activities and emissions outside of the charging zone and a slight increase in emissions for the entire urban area. The size of charging zone, charging method, and charging rate are key factors that directly influence the impact of congestion charging; improved public transit service needs to be considered as a complementary approach with congestion charging. This study is used by Beijing Transportation Environment and Energy Center (BTEC) as reference to support the development of Beijing’s congestion charging policy and regulation.     

A framework for estimating traffic emissions: The development of Passenger Car Emission Unit

In this study, we develop a Passenger Car Emission Unit (PCEU) framework for estimating traffic emissions. The idea is analogous to the use of Passenger Car Unit (PCU) for modeling the congestion effect of different vehicle types. In this approach, we integrate emission modeling and cost evaluation. Different emissions, typically speed-dependent, are integrated as an overall cost via their corresponding external costs. We then develop a normalization procedure to obtain a general trend that is applicable for all vehicle types, which is used to derive a standard cost curve. Different vehicle types with different emission standards are then mapped to this standard cost curve through their corresponding PCEUs that are to be calibrated. Once the standard cost curve and PCEUs have been calibrated, to estimate the overall cost of emission for a particular vehicle, we only need to multiply the corresponding PCEU of that vehicle type to the standard cost curve. We apply this PCEU approach to Hong Kong and obtain promising results. Compared with the results obtained by the full-blown emission model COPERT, the approach achieves high accuracy but obviates tedious inputs typically required for emission estimation.     

Improving fuel consumption and CO2 emissions calculations in urban areas by coupling a dynamic micro traffic model with an instantaneous emissions model

Τhis study demonstrates the combination of a microscopic traffic simulator (AIMSUN) with an instantaneous emissions model (AVL CRUISE) to investigate the impact of traffic congestion on fuel consumption on an urban arterial road. The micro traffic model was enhanced by an improved car-following law according to Morello et al. (2014) and was calibrated to replicate measured driving patterns over an urban corridor in Turin, Italy, operating under adaptive urban traffic control (UTC). The method was implemented to study the impact of congestion on fuel consumption for the category of Euro 5 diesel <1.4 l passenger cars. Free flow and congested conditions led to respective consumption differences of −25.8% and 20.9% over normal traffic. COPERT 5 rather well predicted the impact of congestion but resulted to a much lower relative reduction in free flow conditions. Start and stop system was estimated to reduce consumption by 6% and 11.9% under normal and congested conditions, respectively. Using the same modelling approach, UTC was found to have a positive impact on CO₂ emissions of 8.1% and 4.5% for normal and congested conditions, respectively, considering the Turin vehicle fleet mix for the year 2013. Overall, the study demonstrates that the combination of detailed and validated micro traffic and emissions models offers a powerful combination to study traffic and powertrain impacts on greenhouse gas and fuel consumption of on road vehicles over a city network.     

Modelling dual carriageway lane changing using neural networks

Neural networks offer a potential alternative method of modelling driver behaviour within road traffic systems. This paper explores the application of neural networks to modelling the lane-changing decisions of drivers on dual carriageways. Two approaches are considered. The first, preliminary approach uses a prediction type of neural network with a single hidden layer and the back propagation learning algorithm to model the behaviour of an individual driver. A series of consecutive time-scan traffic patterns, which describe the driver's environment and changes over time as the selected vehicle travels along a link, are input to the neural network, which then predicts the new lane and position of the vehicle. Training data are collected from a human subject using an interactive driving simulation. The trained neural network successfully exhibited the rudiments of driving behaviour in terms of lane and speed changes. A major disadvantage of this approach was the difficulty in recording real-life data, which are required to train the neural network, for individual drivers. The second approach concentrates specifically on lane changing and makes use of a learning vector quantization classification type of neural network. Input to the neural network still consists primarily of time-scan traffic patterns, but the format is changed to facilitate the possibility of data acquisition using image processing. The neural network output classifies the input data by determining the new lane for the vehicle concerned. Performance in both testing and training was very good for data generated by the rule-based driver-decision model of a microscopic simulation. Performance in testing was less satisfactory for data taken directly from a road and highlighted the need for extensive data sets for successful training.     

Optimal location of advance warning for mandatory lane change near a two-lane highway off-ramp

Improper mandatory lane change (MLC) maneuvers in the vicinity of highway off-ramp will jeopardize traffic efficiency and safety. Providing an advance warning for lane change necessity is one of the efficient methods to perform systematic lane change management, which encourages smooth MLC maneuvers occurring at proper locations to mitigate the negative effects of MLC maneuvers on traffic flow nearby off-ramp. However, the state of the art indicates the lack of rigorous methods to optimally locate this advance warning so that the maximum benefit can be obtained. This research is motivated to address this gap. Specifically, the proposed approach considers that the area downstream of the advance warning includes two zones: (i) the green zone whose traffic ensures safe and smooth lane changes without speed deceleration (S-MLC); the start point of the green zone corresponding to the location of the advance warning; (ii) the yellow zone whose traffic leads to rush lane change maneuvers with speed deceleration (D-MLC). An optimization model is proposed to search for the optimal green and yellow zones. Traffic flow theory such as Greenshield model and shock wave analysis are used to analyze the impacts of the S-MLC and D-MLC maneuvers on the traffic delay. A grid search algorithm is applied to solve the optimization model. Numerical experiments conducted on the simulation model developed in Paramics 6.9.3 indicate that the proposed optimization model can identify the optimal location to set the advance MLC warning nearby an off-ramp so that the traffic delay resulting from lane change maneuvers is minimized, and the corresponding capacity drop and traffic oscillation can be efficiently mitigated. Moreover, the experiments validated the consistency of the green and yellow zones obtained in the simulation traffic flow and from the optimization model for a given optimally located MLC advance warning under various traffic regimes. The proposed approach can be implemented by roadside mobile warning facility or on-board GPS for human-driven vehicles, or embedded into lane change aid systems to serve connected and automated vehicles. Thus it will greatly contribute to both literature and engineering practice in lane change management.     

Implications of driving style and road grade for accurate vehicle activity data and emissions estimates

Real-world vehicle operating mode data (2.5 million 1 Hz records), collected by instrumenting the vehicles of 82 volunteer drivers with OBD datalogger and GPS while they drove their routine travel routes, were analyzed to quantify vehicle emissions estimate errors due to road grade and driving style in rural, hilly Vermont. Data were collected in winter and summer for MY 1996 and newer passenger cars and trucks only. EPA MOVES2010b was used to estimate running exhaust emissions associated with measured vehicle activity. Changes in vehicle specific power (VSP) and MOVES operating mode (OpMode) due to proper accounting for real-world road grade indicated emission rate errors between 10% and 48%, depending on pollutant, chiefly because grade-related changes in VSP could shift activity by as many as six OpModes, depending on road type. The correct MOVES OpMode assignment was made only 33–55% of the time when road grade was not included in the VSP calculation. Driving style of individual drivers was difficult to assess due to unknown traffic operations data, but the largest differences between individual drivers were observed on rural restricted roads, where traffic conditions and control have minimal impact. The results suggest the importance of (1) measuring and incorporating real-world road grade in order to correctly assign MOVES emission rates; and (2) developing a driving style typology to account for differences in the MOVES emissions estimates due to driver variability.     

Contrasting the direct use of data from traffic radars and video-cameras with traffic simulation in the estimation of road emissions and PM hotspot analysis

This study investigates the effect of traffic volume and speed data on the simulation of vehicle emissions and hotspot analysis. Data from a microwave radar and video cameras were first used directly for emission modelling. They were then used as input to a traffic simulation model whereby vehicle drive cycles were extracted to estimate emissions. To reach this objective, hourly traffic data were collected from three periods including morning peak (6–9 am), midday (11–2 pm), and afternoon peak (3–6 pm) on a weekday (June 23, 2016) along a high-volume corridor in Toronto, Canada. Traffic volumes were detected by a single radar and two video cameras operated by the Southern Ontario Centre for Atmospheric Aerosol Research. Traffic volume and composition derived from the radar had lower accuracy than the video camera data and the radar performance varied by lane exhibiting poorer performance in the remote lanes. Radar speeds collected at a single point on the corridor had higher variability than simulated traffic speeds, and average speeds were closer after model calibration. Traffic emissions of nitrogen oxides (NOx) and particulate matter (PM₁₀ and PM_2.5) were estimated using radar data as well as using simulated traffic based on various speed aggregation methods. Our results illustrate the range of emission estimates (NO_x: 4.0–27.0 g; PM₁₀: 0.3–4.8 g; PM_2.5: 0.2–1.3 g) for the corridor. The estimates based on radar speeds were at least three times lower than emissions derived from simulated vehicle trajectories. Finally, the PM₁₀ and PM_2.5 near-road concentrations derived from emissions based on simulated speeds were two or three times higher than concentrations based on emissions derived using radar data. Our findings are relevant for project-level emission inventories and PM hot-spot analysis; caution must be exercised when using raw radar data for emission modeling purposes.     

Accounting for traffic speed dynamics when calculating COPERT and PHEM pollutant emissions at the urban scale

Coupling a traffic microsimulation with an emission model is a means of assessing fuel consumptions and pollutant emissions at the urban scale. Dealing with congested states requires the efficient capture of traffic dynamics and their conditioning for the emission model. Two emission models are investigated here: COPERT IV and PHEM v11. Emission calculations were performed at road segments over 6 min periods for an area of Paris covering 3 km². The resulting network fuel consumption (FC) and nitrogen oxide (NOx) emissions are then compared. This article investigates: (i) the sensitivity of COPERT to the mean speed definition, and (ii) how COPERT emission functions can be adapted to cope with vehicle dynamics related to congestion. In addition, emissions are evaluated using detailed traffic output (vehicle trajectories) paired with the instantaneous emission model, PHEM.COPERT emissions are very sensitive to mean speed definition. Using a degraded speed definition leads to an underestimation ranging from −13% to −25% for fuel consumption during congested periods (from −17% to −36% respectively for NOx emissions). Including speed distribution with COPERT leads to higher emissions, especially under congested conditions (+13% for FC and +16% for NOx). Finally, both these implementations are compared to the instantaneous modeling chain results. Performance indicators are introduced to quantify the sensitivity of the coupling to traffic dynamics. Using speed distributions, performance indicators are more or less doubled compared to traditional implementation, but remain lower than when relying on trajectories paired with the PHEM emission model.     

The significant impacts on traffic and emissions of ferrying children to school in Beijing

After having implemented numerous regulations, e.g., coercive policies on vehicle use and purchase, it is becoming increasingly difficult to find further potential to control vehicle emissions in Beijing, as the air quality is still poor. This research provides a different approach for policy-makers to reduce vehicle emissions by managing demand. We found that parents ferrying their children to and from school is an important but long-neglected contributor to traffic congestion and vehicle emissions. This phenomenon is very common in China because of the social culture. In this research, parallel tests during both the school season and the non-school season were adopted, and emissions in both seasons were calculated based on travel demand and emission models. The results revealed that emissions factors (in g/km) for criteria pollutants and CO₂ increased by over 10% during rush hours during the school season due to traffic condition deterioration compared with non-school season. Daily HC, CO, NO_x, PM and CO₂ emissions from the passenger car fleet were 8.3%, 7.8%, 6.4%, 6.3% and 6.5% higher compared with those during the non-school season, respectively. These differences are greater than the total vehicular emission reduction by other control measures in 2014 in Beijing. For policy makers, providing safe and efficient ways to ferry children would be a useful and harmonious strategy for future vehicle emission control.