Optimal roll control of an articulated vehicle: theory and model validation

This paper investigates optimal roll control of an experimental articulated vehicle. The test vehicle and the mathematical model used to design the control strategies are presented. The vehicle model is validated against experimental data from the test vehicle in passive configuration. The initial controller design, performed by Sampson (Sampson, D.J.M. and Cebon, D., 2003a, Achievable roll stability of heavy road vehicles. Proc. Instn. Mech. Engrs, Part D, J. Automobile Engineering, 217(4), 269–287), is reviewed and adapted for the experimental vehicle. The effect of not controlling all the axles on the vehicle is investigated and a variable vehicle speed controller is designed by interpolating between constant speed controllers. Substantial reduction in normalized load transfer is achieved for a range of manoeuvres, both in steady-state and transient conditions.     

Heavy duty vehicle rollover detection and active roll control

This paper presents the results of a comprehensive study on heavy-duty vehicle (HDV) roll stability improvement technology. The proposed rollover threat warning system uses the real-time dynamic model-based time-to-rollover (TTR) metric as a basis for online rollover detections. Its feasibility for implementation in a HDV rollover threat detection system is demonstrated through vehicle dynamic simulation studies. The research on the development of a rollover threat detection system is further enhanced in combination with an active roll control system using active suspension mechanism to improve heavy-duty trucks’ roll stability both in the static cornering and in emergency maneuvers. It has been demonstrated that the roll stability of typical heavy-duty trucks has been largely improved by the proposed active safety monitoring and control system.     

Application of observer-based fault detection in vehicle roll control

This paper describes how observer-based techniques for intelligent fault detection were applied to monitoring an active suspension control system in an experimental articulated heavy vehicle. The aim was to define a practical method for detecting faults, taking into account the nonlinearities of the vehicle. The experimental vehicle was divided conceptually into subsystems, namely the passive dynamics of the trailer, the dynamics of the hydraulic actuators, and the expected response of the closed-loop system. A linear dynamic model was designed for each subsystem. A fault detection observer was then designed for each dynamic model. The observer feedback gains were chosen to optimise estimation by the observer residual of specified errors on the output measurements. The observer residuals were then normalised and combined logically to provide a fault diagnosis. The performance of the fault detection scheme is demonstrated in the case of sensor faults and changes in the operation of the active control system.     

Automatic guidance control of an articulated all-wheel-steered vehicle

This paper presents automatic guidance control of a single-articulated all-wheel-steered vehicle being developed by the Korea Railroad Research Institute. The vehicle has an independent drive motor on each wheel except for the front axle. The guidance controller is designed so that the vehicle follows the given reference path within permissible lateral deviations. We use a three-input/three-output linearised model derived from the nonlinear dynamic model of the vehicle. For the purpose of simplifying the controller and making it tunable, we consider a decentralised control configuration. We first design a second-order decoupling compensator for the two-input/two-output system that is strongly coupled and then design a first-order controller for each decoupled feedback loop by using the characteristic ratio assignment method. The simulation results for the nonlinear dynamic model indicate that the proposed control configuration successfully achieves the design objectives.     

Enhancing roll stability of heavy vehicle by LQR active anti-roll bar control using electronic servo-valve hydraulic actuators

Rollover of heavy vehicle is an important road safety problem world-wide. Although rollovers are relatively rare events, they are usually deadly accidents when they occur. The roll stability loss is the main cause of rollover accidents in which heavy vehicles are involved. In order to improve the roll stability, most of modern heavy vehicles are equipped with passive anti-roll bars to reduce roll motion during cornering or riding on uneven roads. However these may be not sufficient to overcome critical situations. This paper introduces the active anti-roll bars made of four electronic servo-valve hydraulic actuators, which are modelled and integrated in a yaw-roll model of a single unit heavy vehicle. The control signal is the current entering the electronic servo-valve and the output is the force generated by the hydraulic actuator. The active control design is achieved solving a linear optimal control problem based on the linear quadratic regulator (LQR) approach. A comparison of several LQR controllers is provided to allow for tackling the considered multi-objective problems. Simulation results in frequency and time domains show that the use of two active anti-roll bars (front and rear axles) drastically improves the roll stability of the single unit heavy vehicle compared with the passive anti-roll bar.     

Design of a rollover index-based vehicle stability control scheme

This paper presents a rollover index (RI)-based vehicle stability control (VSC) scheme. A rollover index, which indicates an impending rollover, is developed by a roll dynamics phase plane analysis. A model-based roll estimator is designed to estimate the roll angle and roll rate of the vehicle body with lateral acceleration, yaw rate, steering angle and vehicle velocity measurements. The rollover index is computed using an estimated roll angle, estimated roll rate, measured lateral acceleration and time-to-wheel lift. A differential braking control law is designed using a direct yaw control method. The VSC threshold is determined from the rollover index. The effectiveness of the RI, the performance of the estimator and the control scheme are investigated via simulations using a validated vehicle simulator. It is shown that the proposed RI can be a good measure of the danger of rollover and the proposed RI-based VSC scheme can reduce the risk of a rollover.     

7自由度主动悬架整车模型最优控制的研究

应用汽车系统动力学理论,建立了七自由度主动悬架的动力学模型。根据线性二次型最优控制原理设计了主动悬架线性二次型(LQR)控制器,并构建了实现该控制策略的主动悬架控制仿真模型。仿真结果表明:对主动悬架进行最优控制,能够有效地降低车身垂直振动加速度、车身侧倾角加速度和俯仰角加速度。     

Optimal preview game theory approach to vehicle stability controller design

Dynamic game theory brings together different features that are keys to many situations in control design: optimisation behaviour, the presence of multiple agents/players, enduring consequences of decisions and robustness with respect to variability in the environment, etc. In the presented methodology, vehicle stability is represented by a cooperative dynamic/difference game such that its two agents (players), namely the driver and the direct yaw controller (DYC), are working together to provide more stability to the vehicle system. While the driver provides the steering wheel control, the DYC control algorithm is obtained by the Nash game theory to ensure optimal performance as well as robustness to disturbances. The common two-degrees-of-freedom vehicle-handling performance model is put into discrete form to develop the game equations of motion. To evaluate the developed control algorithm, CarSim with its built-in nonlinear vehicle model along with the Pacejka tire model is used. The control algorithm is evaluated for a lane change manoeuvre, and the optimal set of steering angle and corrective yaw moment is calculated and fed to the test vehicle. Simulation results show that the optimal preview control algorithm can significantly reduce lateral velocity, yaw rate, and roll angle, which all contribute to enhancing vehicle stability.     

Multi-performance analyses and design optimisation of hydro-pneumatic suspension system for an articulated frame-steered vehicle

This study investigates the coupled ride and directional performance characteristics of an articulated frame-steered vehicle (AFSV). A three-dimensional multi-body dynamic model of the vehicle is formulated integrating the hydro-mechanical frame steering and hydro-pneumatic suspension (HPS) systems. The model parameters are obtained from field-measured data acquired for an unsuspended AFSV prototype and a validated scaled HPS model. The HPS is implemented only at the front axle, which supports the driver cabin. The main parameters of the HPS, including the piston area, and flow areas of bleed orifices and check valves, are selected through design sensitivity analyses and optimisation, considering ride vibration, and roll- and yaw-plane stability performance measures. These include the frequency-weighted vertical vibration of the front unit, root-mean-square lateral acceleration during the sustained lateral load transfer ratio period prior to absolute rollover of the rear unit, and yaw-mode oscillation frequency following a lateral perturbation of the vehicle. The results suggested that the implementation of the HPS to the front unit alone could help preserve the directional stability limits compared to the unsuspended prototype vehicle and reduce the ride vibration exposure by nearly 30%. The results of sensitivity analyses revealed that the directional stability performance limits are only slightly affected by the HPS parameters. Further reduction in the ride vibration exposure was attained with the optimal design, irrespective of the payload variations. The vehicle operation at relatively higher speeds, however, would yield greater vibration exposure.     

Combined longitudinal and lateral control for automated vehicle guidance

This paper deals with the longitudinal and lateral control of an automotive vehicle within the framework of fully automated guidance. The automotive vehicle is a complex system characterised by highly nonlinear longitudinal and lateral coupled dynamics. Consequently, automated guidance must be simultaneously performed with longitudinal and lateral control. This work presents an automated steering strategy based on nonlinear model predictive control. A nonlinear longitudinal control strategy considering powertrain dynamics is also proposed to cope with the longitudinal speed tracking problem. Finally, a simultaneous longitudinal and lateral control strategy helps to improve the combined control performance. This whole control strategy is tested through simulations showing the effectiveness of the present approach.     

Model predictive control with constraints for a nonlinear adaptive cruise control vehicle model in transition manoeuvres

A vehicle following control law, based on the model predictive control method, to perform transition manoeuvres (TMs) for a nonlinear adaptive cruise control (ACC) vehicle is presented in this paper. The TM controller ultimately establishes a steady-state following distance behind a preceding vehicle to avoid collision, keeping account of acceleration limits, safe distance, and state constraints. The vehicle dynamics model is for continuous-time domain and captures the real dynamics of the sub-vehicle models for steady-state and transient operations. The ACC vehicle can execute the TM successfully and achieves a steady-state in the presence of complex dynamics within the constraint boundaries.     

Active roll control for rollover prevention of heavy articulated vehicles with multiple-rollover-index minimisation

This paper presents the application of a nominal control design algorithm for rollover prevention of heavy articulated vehicles with active anti-roll-bar control. This proposed methodology is based on an extension of linear quadratic regulator control for ‘state derivative-induced (control coupled) output regulation’ problems. For heavy articulated vehicles with multiple axles, a performance index with multiple rollover indices is proposed. The proposed methodology allows us to compare the usefulness of various control configurations (i.e. actuators at different axles of the vehicle) based on the interaction of this control configuration with vehicle dynamics. Application of this methodology to a specific heavy articulated vehicle with a tractor semi-trailer shows that a single active anti-roll-bar system at the trailer unit gives better performance than multiple-axle actuators at tractor and trailer together with the single lane change manoeuvre as the external disturbance. Thus, the proposed methodology of this paper not only highlights the importance of the interactions between control and vehicle dynamics in rollover prevention problems but, in fact, proposes a novel technique to exploit the benefits of these interactions judiciously.     

Coordinated control strategies for active steering,differential braking and active suspension for vehicle stability,handling and safety improvement

ABSTRACT

In this paper, a coordinated control strategy is proposed to provide an effective improvement in handling stability of the vehicle, safety, and comfortable ride for passengers. This control strategy is based on the coordination among active steering, differential braking, and active suspension systems. Two families of controllers are used for this purpose, which are the high order sliding mode and the backstepping controllers. The control strategy was tested on a full nonlinear vehicle model in the environment of MATLAB/Simulink. Rollover avoidance and yaw stability control constraints have been considered. The control system mainly focuses on yaw stability control. When rollover risk is detected, the proposed strategy controls the roll dynamics to decrease rollover propensity. Simulation results for two different critical driving scenarios, the first one is a double lane change and the other one is a J-turn manoeuvre, show the effectiveness of the coordination strategy in stabilising the vehicle, enhancing handling and reducing rollover propensity.     

Development and validation of a Kalman filter-based model for vehicle slip angle estimation

It is well known that vehicle slip angle is one of the most difficult parameters to measure on a vehicle during testing or racing activities. Moreover, the appropriate sensor is very expensive and it is often difficult to fit to a car, especially on race cars. We propose here a strategy to eliminate the need for this sensor by using a mathematical tool which gives a good estimation of the vehicle slip angle. A single-track car model, coupled with an extended Kalman filter, was used in order to achieve the result. Moreover, a tuning procedure is proposed that takes into consideration both nonlinear and saturation characteristics typical of vehicle lateral dynamics. The effectiveness of the proposed algorithm has been proven by both simulation results and real-world data.     

Inverse neuro-fuzzy MR damper model and its application in vibration control of vehicle suspension system

In this paper, a magneto-rheological (MR) damper-based semi-active controller for vehicle suspension is developed. This system consists of a linear quadratic Gauss (LQG) controller as the system controller and an adaptive neuro-fuzzy inference system (ANFIS) inverse model as the damper controller. First, a modified Bouc–Wen model is proposed to characterise the forward dynamic characteristics of the MR damper based on the experimental data. Then, an inverse MR damper model is built using ANFIS technique to determine the input current so as to gain the desired damping force. Finally, a quarter-car suspension model together with the MR damper is set up, and a semi-active controller composed of the LQG controller and the ANFIS inverse model is designed. Simulation results demonstrate that the desired force can be accurately tracked using the ANFIS technique and the semi-active controller can achieve competitive performance as that of active suspension.     

Optimal controller design for a constrained polynomial vehicle system with an input-state linearized model

This paper presents a new controller design method based on a data-mining polynomial algorithm. We show application of a polynomial data-mining algorithm, where an input-state linearized polynomial vehicle model is developed for very low speed operation and, without introducing any processes with fudge factors, control inputs of a nonlinear system are obtained in the original coordinates. We verify the developed modeling method and controller design method through numerical experiments.     

车辆主动悬架自适应模糊PID控制

针对车辆悬架系统的动态特性,将现代控制理论运用于主动悬架控制,提出一种新的控制策略———自适应模糊PID控制,并通过仿真验证了其可行性及有效性。这种新型智能控制策略为车辆主动悬架控制理论的研究提供了一条新思路。     

Adaptive neuron control using an integrated error approach with application to active suspensions

This paper proposes a new neuron control strategy for an active vehicle suspension system, with the emphasis on the study of multivariable and uncertain suspension characteristics. The novelty of this strategy is in the use of integrated error, which consists of multiple output errors in the regulated plant. By combining the integrated error approach with the traditional neuron control (TNC), integrated error neuron control (IENC) is presented. It provides a direct control to the multiple outputs of the control plant simultaneously. Taking a quarter-car model as an example, the proposed control strategy is applied and comparative simulations are carried out with various vehicle parameters and road input conditions. Simulation results prove the effectiveness and robustness of the proposed IENC method. In addition, the newly proposed neuron scheme provides a simple yet efficient new possibility for the control of a class of uncertain multivariable systems similar to an active vehicle suspension.     

线控转向系统控制技术综述

线控转向系统通过线控化、智能化可以实现个性驾驶、辅助驾驶、无人驾驶等目标,是智能网联汽车落地的关键技术,其相关动力学控制技术更是影响线控转向系统整体性能的核心技术.该文介绍了线控转向系统的基本结构类型及其动力学建模,分别对线控转向系统的路感控制技术、稳定性控制技术、容错控制技术等关键技术进行了全面概述,分析了线控转向技...     

基于统一模型的转向-悬架系统最优综合控制方法

通过对车辆底盘系统中的转向和悬架系统建立统一的数学模型,利用M atlab/S imu link仿真,结合最优控制理论,分别对被动悬架兼前轮转向系统与主动悬架兼四轮转向综合控制系统进行了对比研究。理论分析与仿真试验表明,综合控制系统下车辆的操纵稳定性和平顺性都得到了很大的提高。